JVC BD-X200E Instructions Manual page 68

Synchronous Recording
Recording Video & Audio From a Non-Linear Editor (continued)
1. Registering the In Point, Out Point, and Chapter Marks
Use the keyboard to directly enter the In Point, Out Point, and chapter marks.
Registering chapter marks : In order to register chapter marks using the REMOTE CONTROL screen, it will first of all be necessary
REMOTE CONTROL SCREEN ( DV SLAVE )
00:00:00:00
EXIT IN POINT
: : :
h m s f
00:00:00:00
1 2
4 00:25:00:00 5
7 00:40:00:00 8
CHAPTER MANUAL
ADJ
BITRATE 8.0 Mbps
EDL LOAD
TC CANCEL
REMOTE CONTROL SCREEN ( DV SLAVE )
EXIT IN POINT 00:00:00:00
OUT POINT
: : : : : : :
h m s f h m s f h
1 00:00:00:00 2 00:15:00:00 3 00:20:00:00
4 00:25:00:00 5 00:30:00:00 6 00:35:00:00
7 00:40:00:00 8 00:45:00:00 9 00:50:00:00
TC INPUT :
CHAPTER MANUAL
ADJ BITRATE 8.0 Mbps DISC REMAIN
FINALIZE
EDL LOAD
TC CANCEL
EDL LOAD
2. Deleting the In Point, Out Point, and Chapter Marks
REMOTE CONTROL SCREEN ( DV SLAVE )
IN POINT 00:00:00:00
EXIT
: : :
h m s f
1 00:00:00:00 2
4 5
00:25:00:00
7 00:40:00:00 8
CHAPTER MANUAL
ADJ 8.0 Mbps
BITRATE
EDL LOAD
w
TC CANCEL
E-66
to set CHAPTER CREATION from the RECORDER MENU (2/2) screen to MANUAL. If this parameter
is set to AUTO, chapter marks will be automatically setup at specific intervals. The current setting for
CHAPTER CREATION is indicated in this screen's CHAPTER field.
q
OUT POINT 00:10:00:00
: : : : : :
h m s f h m s f
00:15:00:00 00:20:00:00
3
00:30:00:00 6 00:35:00:00
00:45:00:00 9 00:50:00:00
: : :
TC INPUT
000 min
DISC REMAIN
FINALIZE
w
Saving & Loading Time-Code Settings
Once settings have been made, they can be saved on your BD-X200. Even if a different
screen is opened or the power is turned off, stored data can then be loaded by selecting
00:10:00:00
EDL LOAD from the REMOTE CONTROL screen and pressing the Set button.
: :
m s f
If CHAPTER CREATION from the RECORDER MENU (2/2) screen is set to AUTO, it will
not be possible to select EDL LOAD on the REMOTE CONTROL screen.
: :
Whenever an external edit list (EDL) is read or time-code registration is started without
000 min
performing EDL LOAD, the settings will be updated accordingly. As a result, even if EDL
LOAD is selected in such a case, the previous data will not be reloaded.
Refer to page 68 for more details regarding the loading of external EDL.
q
OUT POINT 00:10:00:00
: : : : : :
h m s f h m s f
00:15:00:00 3 00:20:00:00
6
00:30:00:00 00:35:00:00
00:45:00:00 9 00:50:00:00
: : :
TC INPUT
000 min
DISC REMAIN
FINALIZE
Procedure
q Use the arrow keys (†, ©, ∞, and √) to select the point to be
registered (i.e., the In Point or Out Point), and then press the
Enter key.
w Select the TC INPUT button using the cursor keys and input a
time code (hours: minutes: seconds: frames) into the TC input
w
field using the keyboard.
e Press the Enter key.
The time code will be registered for the selected point.
If both IN point and OUT point are not selected, the time code
will be registered as a chapter point
When a time code is registered for a chapter mark, the chapter
list will be sorted from the smallest time-code values, and the
newly registered point will be highlighted.
q Use the cursor buttons (t, 8, 7, and 6) to select the point to
be deleted (i.e., the In Point, Out Point, or a chapter mark from
the chapter list), and then press the SET button.
w Use the cursor buttons (t, 8, 7, and 6) to select TC CANCEL
and press the SET button.
The selected point (i.e., In Point, Out Point, or a chapter mark
from the chapter list) will be deleted.
Whenever a chapter mark is deleted, the chapter list will be
sorted.