Advertisement
Quick Links
Keep this User's Guide at hand for quick reference at any time it may be required.
Read "SAFETY NOTES" first, then set up this kit.
Provide this User's Guide along with this kit when you transfer to the third party.
N8143-56F/56E Rack Conversion Kit
Preface
This product is mechanical parts for installing NEC Express server into 19-inch rack system.
Read this document and the manual of the NEC Express server to understand installation
method before installing this product to the server.
SAFTY NOTES
Follow instructions given in this document for proper installation and safe use of the server.
Refer to the User's guide of the NEC Express server regarding the safety indications.
Install this kit only to the server which define as optional parts.
Failure to follow these instructions may cause the server to operate
incorrectly and/or personal injury or damages of surrounding servers to
occur.
More than two persons are required to carry or install the rack.
Failure to follow this instruction may cause the rack to fall to result in
personal injury and/or breakage of surrounding servers.
Read this document and the manual of the NEC Express server to
understand installation method before installing this product to the
server. Failure to follow these instructions may cause the server to
operate incorrectly and/or personal injury or damages of surrounding
servers to occur.
Attach cables not to contact the slide rail assembly and neighboring
units. Failure to follow these instructions may cause the server to
operate incorrectly and/or personal injury or damages of surrounding
servers to occur.
Do not disassemble, repair, or modify the server. Otherwise, an electric
shock or fire may be caused.
User's Guide
‚P
856-122660-101-A Rev.1.2
Advertisement
Related Manuals for NEC N8143-56F/56E
Summary of Contents for NEC N8143-56F/56E
- Page 1 N8143-56F/56E Rack Conversion Kit User’s Guide Preface This product is mechanical parts for installing NEC Express server into 19-inch rack system. Read this document and the manual of the NEC Express server to understand installation method before installing this product to the server.
- Page 2 Chapter 1 Preparation for Installation This chapter describes preparations required for installing the server on a 19-inch rack step by step. Step 1 Unpacking The rack conversion kit contains the following components. Make sure that everything listed below are inside and no damage is observed after unpacking. 13,14 ‚Q...
-
Page 3: Table Of Contents
Part Name Notes Front Cover Slide Rail Assembly Cable Arm Arm Bracket Arm Stopper EIA Mounting Flange to Rear Arm Support (1) Mounting Flange : 700_743mm EIA Mounting Flange to Rear Arm Support (2) Mounting Flange : 743_900mm Foot Cover Device Cover For 5.25”... - Page 4 Chapter 2 Installation This chapter describes the procedures for installing the rack mountable server into a 19-inch rack. Step 1 Convert from tower type to rack-mount type Pull the hinge pin out. Then slide the front bezel to remove it from the other hinge pin and remove the front bezel.
-
Page 5: Front Cover
Fix the HDD cover (1 or 2) with the screw (D) to the inside of front cover. ( Do not attach the HDD cover into Hot Plug SCSI HDD (6slots) model. ) Fixed HDD (4slots) model Fix HDD cover (1) with four screws (D) Front Cover HDD Cover (1) Hot Plug ATA HDD (4slots) model... -
Page 6: Slide Rail Assembly
Step2 Mounting the server into the rack (1) Fully slide the rails out until they lock in place. And while pressing down on the release lever, slide the rails to remove the inner rail. Slide Rail Assembly Outer Rail Inner Rail Release Lever Fix the inner rail with eight screws (A) to both sides of the server. - Page 7 Loosen three screws for fixing the rear mounting bracket in order to move the rear mounting bracket. Repeat this step for the other rail. Rear Mounting Slide Rail Assembly Outer Rail Screws for Rear Mounting bracket (5) Place slide rail assemblies to the mounting flanges of the rack. Attach the washer to the screw (B) and then fix both sides of slide rails with eight screws (B).
- Page 8 (7) Slide two slide rails out from the rack until they were locked. And then with three or more persons assisting you, lift the server and align the inner rails attached to the both side of the server with the extended rails. (8) Insert the inner rails into the extended slide rails and push the server into the rack until it stops.
-
Page 9: Arm Bracket
Step 3 Installing the cable arm and cables (1) Fix the arm bracket with two screws (D) to the back of the server. Server Arm Bracket When the distance between the front mounting flange and the rear mounting flange is about 743mm, align one end of the cable arm with the outside of the core nuts installed to the rear of the rack frame and secure it with the two screws (B). - Page 10 (3) When the distance is from 700mm to 742mm, use the arm support (1) to adjust the position of cable arm. (4) When the distance is from 745mm to 900mm, use the arm support (2) to adjust the position of cable arm.. Arm Support (2) Arm Support (1) Cable Arm...
- Page 11 (6) Check to see that no excess force is applied to the cable arm by pulling out the server and pushing it back in. And this cable arm is rotated to backside for connection of cables and exchange of the power supply unit. Check to see that no excess force is applied to the cable arm by rotating it.
-
Page 12: Arm Stopper
Check to see that no excess force is applied to cables by pulling out the server and pushing it back in. And this cable arm is rotated to backside for connection of cables and exchange of the power supply unit. Check to see that no excess force is applied to cables by rotating it. -
Page 13: Model Name Label
(1) Stick the model name label corresponding to each model on the front cover. (2) Stick the icon label corresponding to each model on the front cover. Icon Label Model Name Label 10mm 10mm For NEC Express5800/120Lg For NEC Express5800/120Lh For NEC Express5800/120Ef For NEC Express5800/120Eg Model Name Label For NEC Express5800/120Lg... - Page 14 Chapter 3 Operation Step 1 Attaching/Removing the arm stopper This cable arm is rotated to backside for connection of external cables and exchange of the power supply unit. This step describes the procedures for rotating the cable arm to backside. Loosen the screw (D) and slide the arm stopper to upside and then remove the arm stopper.
- Page 15 Step 2 Sliding the server out from the rack It is necessary to slide the server out from the rack when doing maintenance of the internal components. This step describes the procedures for sliding the server out from the rack. Note sufficiently that your fingers may not be caught between a rail and other mechanical parts or cut by a rail at installation or removal of the server from the rack.