Advertisement
Setting Oven
Controls
Setting
Self Clean
(cont'd.)
As soon as Self Clean
becomes
active,
a motor
driven
lock
mechanism
will begin
locking
the oven door automatically,
door
Loc will appear
in the display
(Figure
52). DO NOT open the
oven door when door Loc is displayed
(allow
15 seconds
for the
lock mechanism
to lock the oven).
Once the oven door has locked,
CLn will appear
in the display
indicating
Self Clean
has started
(Figure 53).
Figure 52:
Door locking
Figure 53:
Oven
in clean mode
Figure 54:
Oven too hot for
Figure 55:
Door opens when
door to unlock
oven has cooled
When
Self Clean
is finished
1.
CIn message
will turn off and Hot will appear
in display
window
(Figure 54).
2.
Once the oven has cooled
down
(about
1 hour) and Hot is
no longer
displayed,
the door Opn
message
will appear
(Figure 55). When
this message
turns off the oven door may
be opened.
Use caution
when opening
the oven door after
self-cleaning.
The oven may still be VERY HOT and can cause
burns. To avoid
possible
burns stand to the side of the oven
when opening
the oven door to allow
hot air or steam to escape.
3.
When
the oven interior
has completely
cooled,
wipe
away
any residue or powdered
ash with a damp
cloth or paper
towel.
Important
note.
The kitchen
area should
be well ventilated
using an open
window,
ventilation
fan or exhaust
hood
during
the 1st self-
clean cycle to help eliminate
the normal
odors
associated
with the 1st self-clean
cycle.
When
the clean time finishes the oven door will remain
locked
until the range has cooled
sufficiently.
In addition
to
the clean time that was programmed,
you must allow about
1 additional
hour for the oven to cool before
you will be
able to open
the oven door.
The Self Clean function
will not operate
whenever
a radiant
surface
element
is ON
or the oven lockout
is active.
Setting Delay Start Self Clean
To start a delay Self Clean
with default
clean time of 3 hours
and a start time of 9:00
o'clock:
1.
Be sure the clock is set with the correct
time of day, the oven
is empty
and ALL oven racks are removed.
Be sure oven
door is completely
closed.
2.
Press Delay Start.
3.
4.
5.
6.
Using numeric
keypad
enter 9 00.
Press
to accept.
STAK[
J
Press Self Clean.
Press
START"
If it becomes
necessary to stop Self Clean
when active:
1.
Press s_p •
2.
If Self Clean
has heated
the oven to a high temperature,
allow
enough
time for the oven to cool and the door Opn
message
to appear
(Figure 55). When
this message
turns
OFF the oven may be opened.
3.
Before
restarting
Self Clean,
be sure to read important
notes below.
Important
note.
•
When
Self Clean
function
is active
you may check
the
amount
of clean time remaining
by pressing
Self Clean
once.
If your control
is set with the default
12 hour display
mode,
the Delay
Self Clean
can only be set to start up to 11 hours
and 59 minutes
in advance.
To set a Delay Start Self Clean
to begin 12 or more hours (maximum
is 23 hours and 59
minutes)
in advance,
be sure to set the control
for 24 hour
display
mode.
If Self Clean
was active
and then interrupted
by a power
failure
or cancelled
before
the oven was thoroughly
cleaned,
it may be necessary
to run another
self-clean
cycle
again.
If the oven temperature
was high enough
when inter-
rupted
your oven control
may not allow
another
self-clean
cycle to be set for up to 4 hours after the interruption.
34
Advertisement
