Download Print this page

Advertisement

D-Link
DVG-1402S
2Voice + 4SW VoIP Router
Manual
Building Networks for People
Version B.1

Advertisement

   Also See for D-Link 2Voice + 4SW VoIP Router DVG-1402S

   Related Manuals for D-Link 2Voice + 4SW VoIP Router DVG-1402S

   Summary of Contents for D-Link 2Voice + 4SW VoIP Router DVG-1402S

  • Page 1

    D-Link DVG-1402S 2Voice + 4SW VoIP Router Manual Building Networks for People Version B.1...

  • Page 2: Table Of Contents

    Contents Package Contents......................3 Introduction ........................4 Rear Panel Connections....................5 Front Panel LEDs ......................6 Features ........................... 7 Installation ........................8 Using the Configuration Wizard ..................9 Home > WAN....................... 9 Home > WAN......................10 Home > WAN > Static IP Address ................12 Home >...

  • Page 3

    Home > VoIP > Manage Features > Reject Incoming Call........31 Home > VoIP > Manage Features > Block Outgoing Call ......... 32 Home > DHCP ......................33 Home > Proxy DNS ....................35 Advanced > Virtual Server ..................36 Advanced >...

  • Page 4: Package Contents

    Package Contents • D-Link DVG-1402S Router • Power Adapter - AC 12V, 1.2A • Manual and Warranty on CD • Quick Installation Guide • Ethernet Cable (All the Ethernet ports on DVG-1402S are Auto-MDIX) Note: Using a power supply with a different voltage rating than the one included with the DVG-1402S will cause damage and void the warranty for this product.

  • Page 5: Introduction

    Introduction The D-Link DVG-1402S High-Speed VoIP Router Links traditional telephony networks to IP networks with conventional telephony devices such as analog phones or fax machines. It can reduce long distance phone charges and deliver toll-quality voice communication over the IP network. This gateway provides two loop start Foreign Exchange Subscriber (FXS) ports and four LAN ports.

  • Page 6: Rear Panel Connections

    Rear Panel Connections Phone Auto MDI/MDIX Factory Reset Connections LAN Ports Button Connect to Connect the Pressing this your phones Ethernet cable button will using from computers restore the router standard on your LAN to to its factory phone these ports. default settings.

  • Page 7: Front Panel Leds

    Front Panel LEDs Status LED WAN LED Phone LEDs A blinking LED An active LED The Hook LED will indicates the indicates a link light when a DVG-1402S is has been telephone is off the functioning established. A hook. A blinking LED properly.

  • Page 8: Features

    Features • 1 NWay 10/100BASE-TX Fast Ethernet port for WAN-connection • 4 NWay 10/100BASE-TX Fast Ethernet port for LAN-connection • 2 Foreign Exchange Subscriber (FXS) POTS ports (RJ-11 Jacks) • Voice Activity Detection (VAD) /Comfort Noise Generation (CNG) • Silence suppression to reduce bandwidth consumption. •...

  • Page 9: Installation

    Connect the Cable or DSL modem to the DVG-1402S VoIP Router (see the printed Quick Installation Guide included with your router.) Install the D-Link DFE-530TX+ adapter into a desktop computer. The four Ethernet LAN ports of the DVG-1402S are Auto MDI/MDIX and will work with both Straight-Through and Cross-over cable.

  • Page 10: Using The Configuration Wizard

    Using the Configuration Wizard Whenever you want to configure 192.168.15.1 your network or the DVG-1402S, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of the DVG-1402S. The DVG-1402S default IP Address is shown to the right: •...

  • Page 11: Home > Wan

    Home > WAN Dynamic Choose Dynamic IP Address to obtain IP Address information automatically from your ISP. This option should be selected if your ISP has not supplied you with an IP address. This option is commonly used for Cable modem services. Host Name The Host Name is optional but may be required by some ISPs.

  • Page 12

    MAC address on the Broadband Router. You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP.

  • Page 13: Home > Wan > Static Ip Address

    Home > WAN > Static IP Address Static IP Address Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP.

  • Page 14

    Input the primary DNS (Domain Name Server) IP address provided by your ISP This is an optional DNS Address entry to be used if the primary Secondary DNS DNS Fails. Address Upstream Bandwidth The upstream bandwidth can be set for the type of packets that the will be sent.

  • Page 15: Home > Wan > Pppoe

    Home > WAN > PPPoE Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used services. PPPoE Choose this option if your ISP uses PPPoE. (Most DSL users will select this option.) Password Enter The PPPoE user name provided to you by your ISP.

  • Page 16

    provided by your ISP Secondary DNS This is an optional DNS Address entry to be used if the primary Address DNS fails. The upstream bandwidth can be set to suit the type of packets Upstream that the connection will be sending. The bandwidth can be Bandwidth maximized for voice packets and limited for data that requires less throughput.

  • Page 17: Home > Lan

    Home > LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DVG-1402S and may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.

  • Page 18: Home > Voip

    Home > VoIP All of the screens necessary to setup and configure the router to handle VoIP traffic are accessed from the screen shown below. To access any of the individual configuration screens, click on the corresponding radio-button and that screen will appear.

  • Page 19

    Home > VoIP > Server Configuration The Router can be configured to handle voice signals over the Internet Protocol (Voice over IP − VoIP). The screen shown to the right, along with those on the following pages are used to configure your router to communicate with the devices that will send and receive telephone calls over...

  • Page 20

    Server FQDN Use this drop-down menu to Enable or Disable the Server Fully Qualified Domain Name (FQDN) function. This is disabled when the SIP URL domain name is different from the SIP proxy server domain name. The phone will then use the domain name in Domain Name field as part of SIP URL but send and receive SIP messages through the SIP proxy server defined in the Service Domain field.

  • Page 21: Home > Voip > Provisioning

    Home > VoIP > Provisioning Provisioning is a function that automatically updates your DVG-1402S’s VoIP configuration by using a TFTP server located on the Internet. If you have accesses to such a service, you will need to know the URL and Proxy Address of the Provisioning Server.

  • Page 23: Home > Voip > Stun Configuration

    Home > VoIP > STUN Configuration Simple Traversal of UDP over NAT (STUN) − is a protocol which enables a VoIP device, such as this router or an IP phone, to detect the presence and type of NAT behind which the phone is placed.

  • Page 24: Home > Voip > User Agent

    Home > VoIP > User Agent The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Same Phone Number Use this field to Enable or Disable the use of the same telephone number for the User Agent as for the Server Agent. Index Use this field to assign line 1 or line 2 telephone sockets (on the back of the router) to the information entered in the User...

  • Page 25: Home > Voip > Peer To Peer

    Home > VoIP > Peer to Peer The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Phone Number The telephone number assigned to this entry User IP Address Enter the IP address of the remote peer in this field. Port Enter the UDP port number the remote peer will use to make the connection in this field...

  • Page 26: Home > Voip > Telephony

    Home > VoIP > Telephony The Router can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VoIP). Index Use this field to assign line 1 or line 2 telephone sockets (on the back of the router) to the information entered in the User Agent.

  • Page 27: Home > Voip > Speed Dial

    Home > VoIP > Speed Dial The Router can be configured to dial a specified telephone number when you enter a numerical dial code. For example, you could assign 22 to the telephone number 555-1234. Then you can dial that telephone number by entering 22.

  • Page 28: Home > Voip > Misc

    Home > VoIP > Misc. Instead of adding additional lines to handle different telephone numbers, distinctive rings can be set to allow more than one telephone number to reach the same line. Calls coming in on different numbers on the same line can be identified by their distinctive ring pattern.

  • Page 29: Home > Voip > Misc. > Ring Cadence

    Home > VoIP > Misc. > Ring Cadence By using the Ring Cadence window, you can set up to 8 distinct ring patterns. The ring pattern of each distinct ring can be configured by setting the On and Off time. The amount of times that the ring pattern will repeat itself can also be set.

  • Page 30: Home > Voip > Misc. > Ring Default Rule

    Home > VoIP > Misc. > Ring Default Rule The Ring Default Rule is set for inbound callers that are not defined by the Ring Rule. One Ring Default Rule can be set for each VoIP port. Use this pull-down menu to select a Ring Cadence for the Ring Ring Cadence Default Rule.

  • Page 31: Home > Voip > Misc. > Ring Rule

    Home > VoIP > Misc. > Ring Rule You can use the Ring Rule window to assign Caller IDs to frequently received inbound calls. Any call that has been assigned a caller ID will have its ID number displayed on the receiver’s caller display.

  • Page 32: Home > Voip > Manage Features > Reject Incoming Call

    Home > VoIP > Manage Features > Reject Incoming Call You can configure the router to reject incoming calls from particular telephone numbers by entering the telephone number in the screen shown below. Name Enter a name to identify the current entry. PhoneNum Enter the telephone number you want to block incoming calls from.

  • Page 33: Home > Voip > Manage Features > Block Outgoing Call

    Home > VoIP > Manage Features > Block Outgoing Call You can configure the router to reject outgoing calls from particular telephone numbers by entering the telephone number in the screen shown below. Name Enter a name to identify the current entry. PhoneNum Enter the telephone number you want to block outgoing calls to.

  • Page 34: Home > Dhcp

    Home > DHCP Dynamic Host Configuration Protocol (DHCP) allows the gateway to automatically obtain the IP address from a DHCP server on the service provider’s network. The service provider assigns a global IP address from a pool of addresses available to the service provider.

  • Page 35

    as HTTP or FTP. First, the user must enable the Static DHCP function by clicking the corresponding Enabled radio button. Next the user must enter the host name and the IP address for that computer by entering the last numbers into the space provided in the IP Address field.

  • Page 36: Home > Proxy Dns

    Home > Proxy DNS State Use this drop down menu to enable or disable the Proxy DNS. Proxy DNS IP Address Enter the IP Address of the Proxy DNS.

  • Page 37: Advanced > Virtual Server

    Advanced > Virtual Server To view the following window, click on the Advanced tab at the top of the window and then click the Virtual Server button to the left. The Virtual Server will allow remote users access to various services outside of their LAN through a public IP address, such as FTP (File Transfer Protocol) or HTTPS (Secure Web).

  • Page 38

    These external services may be modified by clicking its corresponding edit icon, or they may be deleted by clicking the corresponding delete icon. Though there are seven fields available to configure the Virtual Server, in most cases, only the IP address of the Virtual Server will be needed for implementation.

  • Page 39: Advanced > Filters

    Advanced > Filters Packet filtering is a basic security measure that should be used on any network that is exposed to a security risk. A packet filter system examines data packets and scrutinizes them in order to control network access. Filtering rules determine whether packets are...

  • Page 40: Advanced > Filters > Ip Filters

    passed through the Router from either side of the gateway. The rules are created and controlled by the network administrator and can be precisely defined. These rules are used to block access to the LAN from outside the network and/or to deny access to the WAN from within the network.

  • Page 41: Advanced > Filters > Mac Filters

    Protocol The protocol associated with this IP filter. The user may choose between TCP, UDP or Both. IP Address An IP address or range of IP addresses that will be denied access to the Internet. Subnet Mask The subnet mask that corresponds to the IP address above. Start Port/End Port A port or range of ports that will be denied access to the Internet.

  • Page 42: Advanced > Firewall

    Advanced > Firewall This Router comes equipped with a firewall. The Firewall configuration screen allows the Router to enforce specific predefined policies intended to protect against certain common types of attacks. To configure the Router’s firewall, click the Advanced tab at the top of the screen and then the Firewall tab to the left.

  • Page 43: Advanced > Rip

    Advanced > Routing > RIP Configuration RIP − Routing Information Protocol − specifies how routers exchange information. With RIP, routers occasionally exchange entire routing tables. You can select RIPv1 or RIPv2 by clicking the radio button under the Version heading, and then select On or Off by clicking the radio button under the State heading.

  • Page 44: Advanced > Routing

    Advanced > Routing > Static Route The Routing table, shown to the right, allows you to enter static routes between computers on both the WAN (Internet) and your LAN. IP Address Enter the IP Address of the subnet or device where packets are to be routed.

  • Page 45: Advanced > Nat > Nat Configuration

    Advanced > NAT > NAT Configuration Network Address Translation (NAT) is a method by which the router translates between the IP address your ISP assigns to your account and the IP addresses assigned to the PCs on your LAN. NAT Interface IP Address This field displays the current IP address of the LAN side of the router.

  • Page 46: Advanced > Nat > Dynamic Nat

    Advanced > NAT > Dynamic NAT Network Address Translation (NAT) is a method by which the router translates between the IP address your ISP assigns to your account and the IP addresses assigned to the PCs on your LAN. The Dynamic NAT entries are displayed below the Dynamic NAT...

  • Page 47: Advanced > Nat > Static Nat

    Advanced > NAT > Static NAT Network Address Translation (NAT) is a method by which the router translates between the IP address your ISP assigns to your account and the IP addresses assigned to the PCs on your LAN. Index This is an index number that will be used to identify this NAT table entry Local IP Address...

  • Page 48: Tools > Admin

    Tools > Admin At this page, the DVG-1402S administrator can change the system password. There are two accounts that can access the Broadband Router’s Web-Management interface. They are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes.

  • Page 49: Tools > System

    Tools > System Backup Click Backup to backup the configuration file to your local hard drive. Restore Configuration To restore the configuration file click on Browse to search the File local hard drive and locate the configuration file to be used for the configuration restoration.

  • Page 50: Tools > Firmware

    Tools > Firmware You can update both the software and firmware of the Router. Please check the D-Link Support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site. Software Update Enter the TFTP server address.

  • Page 51: Tools > Snmp

    Tools > SNMP This menu can be accessed directly by clicking on the SNMP button or hyperlink in the Tools setup menu. Simple Network Management Protocol (SNMP) is an OSI Layer 7 Application designed specifically for managing and monitoring network devices. SNMP enables network management stations to read and modify the settings of...

  • Page 52: Tools > Time

    Tools > Time The system time is the time used by the DVG-1402S for scheduling services. You can manually set the time, connect to a NTP (network time protocol) server or synchronize the time on the router with your PC. If an NTP server is set, you will only need to set the time zone (in the set up wizard).

  • Page 53: Status > Device Info

    Status > Device Info This page displays current information for the DVG-1402S. It will display LAN, WAN, Disk Information statistics. This window will show the DVG-1402S’s working status: IP Address: WAN/Public IP Address Subnet Mask: WAN/Public Subnet Mask Default Gateway: WAN/Public Gateway IP Address LAN MAC Address: MAC address of the DVG-1402S IP Address: LAN/Private IP Address of the DVG-1402S Subnet Mask: LAN/Private Subnet Mask of the DVG-1402S...

  • Page 54: Status > Stats

    Status > Stats The Broadband Router keeps a running log of events and activities occurring on the Router. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Settings. The screen above displays the Traffic Statistics. Here you can view the amount of packets that pass through the DVG-1402S on both the WAN and the LAN ports.

  • Page 55: Status > Diagnostics

    Status > Diagnostics The Diagnostics window allows users to test the functionality of the router by executing a ping test. Enter the IP address of the Ping Target and then click Test.

  • Page 56: Help

    Help The Help tab will give basic information referring to various screens locted in the Router. To view a specific section, click on its hyperlinked name. A new window of information will appear.

  • Page 57: Technical Specifications

    Technical Specifications Standards IEEE 802.3 IEEE 802.3u VPN Pass Through/ Multi-Sessions PPTP L2TP I PSec Device Management Web-Based- Internet Explorer v6 or later; Netscape Navigator v6 or later; or other Java-enabled browsers DHCP Server and Client Advanced Firewall Features NAT with VPN Passthrough (Network Address Translation) MAC Filtering IP Filtering URL Filtering...

  • Page 58

    Status Physical Dimensions: L = 7.56 inches (192mm) W = 4.65 inches (118mm) H = 1.22 inches (31 mm) Power Input: Ext. Power Supply DC 12V, 1.5A Weight: 10.8 oz. (0.3kg) Warranty: 3 year (depends on D-Link global warranty policy)

  • Page 59: Technical Support

    Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.

Comments to this Manuals

Symbols: 0
Latest comments: