Table of Contents
Advertisement
A U T O M A T I C
T R A N S M I S S I O N
R E M O T E
S T A R T E R
AS-2510 TW
Installation Guide
A note concerning the battery inside the transmitter:
Depending on the usage of the transmitter, the battery can last anywhere between 3 to 6
months. When the battery is low, it the transmitter will emit two beeps in a repetitive
cycle. At that point you should replace your battery with a new one. That is why we
recommend that you keep a spare battery somewhere handy such as the glove
compartment.
Notice
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of
the product, be that either damage to the vehicle itself or to the Unit. This Unit must be installed by a certified
technician using all safety devices supplied. Please note that this guide has been written for properly trained
Autostart technicians: a certain level of skills and knowledge is therefore assumed. Please review the
Installation Guide carefully before beginning any work.
Warning
automatic
This Remote Car Starter is designed for vehicles with an
Transmission only. Before
installing the Unit, test that the vehicle does not start when the Gear Select Lever is in the "Drive" position. If it
starts in gear, install a manual-transmission remote starter system instead.
DOC .1.00
– November 5, 2003
Gp CA Lp
Manufactured in Canada by Autostart
Advertisement
Table of Contents
Related Manuals for Autostart AS-2510 TW
Summary of Contents for Autostart AS-2510 TW
- Page 1 Unit. This Unit must be installed by a certified technician using all safety devices supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
-
Page 2: Table Of Contents
– Remote Car Starter Control Unit – FM long-range Transceiver – multi-channel 5-button Remote Control – plug-in L.E.D. – six-pin 14 AWG Harness (Ignition Harness) – five-pin 18 AWG Harness (Main Harness) – twelve-pin 22 AWG Harness (Accessories Harness) P. 2 Installation Guide AS-2510 TW... -
Page 3: Installation Points To Remember
Make sure that all the switches and controls operate properly. Verify that the vehicle starts and idles properly. Make sure that all safety equipment is installed: the Valet Button (if provided), the Hood Switch and the Warning Label. AS-2510 TW Installation Guide P. 3... -
Page 4: Harness Description
B+ connection on the Battery. Connect to the Ignition wire of the vehicle. The source wire should (+) Ignition YELLOW have +12 V with the Ignition Key in the IGNITION ON (RUN) output (30 A) positions. CRANK P. 4 Installation Guide AS-2510 TW... - Page 5 YELLOW Light output Note: ensure that the voltage does not decrease or increase when the dimmer control switch is turned. If the voltage goes up or down, find another Parking Light wire. AS-2510 TW Installation Guide P. 5...
-
Page 6: 12-Pin Accessories Harness
ORANGE sec after release of the buttons. output toggles (max. 30 sec.). LOCK UNLOCK ON / OFF toggles (max. 60 sec.). LOCK UNLOCK ON / OFF 4. Priority Door Access (2 press of UNLOCK P. 6 Installation Guide AS-2510 TW... - Page 7 GROUND wire, make sure they are diode isolated from one OUT WHEN RUNNING another: feedback may otherwise occur, causing damage to the vehicle. GREY (–) N/A This pin is not used. Leave it empty. AS-2510 TW Installation Guide P. 7...
- Page 8 2-Pin Harness Wire Colour Function Description BLUE/ (–) N/A This pin is not used. Leave it empty. WHITE (–) Parking YELLOW 500 mA negative Parking Light output. Light output P. 8 Installation Guide AS-2510 TW...
-
Page 9: Flashing The Hood Pin Switch
20 seconds to select a sub-menu. If you do not select a sub-menu within 20 seconds, the Remote Car Starter will exit Programming Mode and you will have to flash the Hood Pin switch once again. AS-2510 TW Installation Guide P. 9... -
Page 10: The Programming Assistance Button
The Remote Car Starter is equipped with three custom programming Modes that allow the installer to custom-fit the system outputs according to installation requirements. The Programming Options are designed to facilitate interfacing with all vehicle types. (See section Table of Programming Options later in this Guide.) P. 10 Installation Guide AS-2510 TW... -
Page 11: Programming Options
FUNCTION 2 – Secure Lock OPTION 1* Secure Lock (1-sec. Disarm pulse) DISABLED OPTION 2 Secure Lock in Smart Mode ENABLED OPTION 3 Secure Lock (1/2-sec. Disarm pulse) DISABLED OPTION 4 Secure Lock in Standard Mode ENABLED AS-2510 TW Installation Guide P. 11... - Page 12 1-sec. output when button is pressed for 3 sec. with Ignition TRUNK or under remote run OPTION 2* Constant output while the button is pressed TRUNK OPTION 3 Output with Disarm and Rearm pulses P. 12 Installation Guide AS-2510 TW...
-
Page 13: Tach Programming
4. Once the Engine is running idle, press the Brake Pedal and keep it down until you hear the Parking Lights Output flash 5 times. – Release the Brake Pedal: Tach Programming is now complete. Table 5: Multi-speed Tach Programming AS-2510 TW Installation Guide P. 13... -
Page 14: Automatic Tach Programming
A system reset will set the Remote Car Starter back to the default values: 30 ms. Testing Before putting back the vehicle together, it is recommended to check that the system operates properly. The following testing procedures should be used to verify proper P. 14 Installation Guide AS-2510 TW... -
Page 15: Closing Up
Always make all your connections before plugging in the Remote Car Starter, and be sure to test all functions properly before closing up the installation. Make sure the Warning Label is applied on a visible place under the Hood. AS-2510 TW Installation Guide P. 15... -
Page 16: Supplementary Information
Doors. 4 seconds after shutdown, Secure Lock will re-lock all Doors (arming the system once again). Please note that most OEM systems will not rearm the Alarm while the Engine is running, but will still lock the Doors. P. 16 Installation Guide AS-2510 TW... -
Page 17: Smart Secure Lock
1. Flash the Hood Pin switch (see Table 1) – Once inside Programming Mode, you have 13 seconds to complete the next step. AS-2510 TW Installation Guide P. 17... -
Page 18: Events Logging
4 x = Brakes 5 x = No Tach Cut-off 6 x = Hood 7 x = Engine Running, no Ignition detected, or Tach before Start Note: “ ” stands for one flash of the Parking Lights P. 18 Installation Guide AS-2510 TW... -
Page 19: Diagnostics - Parking Light Flash Table
If the unit gives irregular signals (1 to 10 flashes followed by a pause, Irregular followed by further flashes), the system is playing back Start Failure Codes. This occurs when the Hood Pin-switch is pressed three times. Constant Panic Mode triggered. flashes up to 30 sec. AS-2510 TW Installation Guide P. 19...