Important Safety Instructions For Use Of The Cordless Circular Saw - Hitachi C18DLP4 - 18V Li-Ion 6-1/2" Circular Saw Safety Instructions And Instruction Manual

English
21. Never operate without all guards in place.
Never operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of
a guard or safety feature, be sure to replace the
guard or safety feature before resuming operation
of the tool.
22. Use right tool.
Don't force small tool or attachment to do the job
of a heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
23. Never use a power tool for applications other than
those specified.
Never use a power tool for applications other than
those specified in the Instruction Manual.
24. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
Never allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
25. Definitions for symbols.
V ............... volts
— .............. direct current
---
n .............. no load speed
o
---/min ...... revolutions or reciprocation per
minute
26. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
27. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
28. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
29. Never use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a Hitachi authorized service center.
30. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
31. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
6
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dried thoroughly.
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE CORDLESS CIRCULAR SAW
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of the cordless circular
saw. To avoid these risks, follow these basic safety
instructions:
1. Wear ear plugs when using the tool for extended
periods. Prolonged exposure to high intensity
noise can cause hearing loss.
2. Never wedge or tie lower guard open. Check
operation of lower guard before each use. Do not
use if lower guard does not close briskly over saw
blade.
CAUTION:
If saw is dropped, safety cover may be bent
restricting full return.
3. For this mode, the saw blades range should be
from 165 mm to 160 mm.
4. Never place hands or other body parts near the
saw blade during operation. Hold the circular saw
by its handle only.
5. Because the cordless circular saw operates by
battery power, be aware of the fact that it can begin
to operate at any time.
6. Wear eye and ear protection at all times.
7. When working at elevated locations, clear the area
of other people and aware of conditions below you.
8. It is important to support the work properly and to
hold the saw firmly to prevent loss of control which
could cause personal injury.
9. Guard against kickback: Kickback occurs when the
saw stalls rapidly and is driven back towards the
operator. Release switch immediately if blade
binds or saw stalls.
• Keep blades sharp.
• Support the panel near the cut.
• Use guide when ripping.
• Don't force tool.
• Stay alert exercise control
• Don't remove saw from work during a cut while
the blade is moving.
10. In operating, keep hold main body firmly.
11. Keep the light ON during cutting operation only.
If it is lit ON in other cases, the main body switch
can be inadvertently turned ON, resulting in
unexpected accidents.