Synexis Ts2 Stationary Transmitter, Synexis C8, C10, C20, C30, Chp Chargers - Beyerdynamic Synexis Operating Instructions Manual

Synexis – Important Safety Instructions
1.2

Synexis TS2 stationary transmitter, Synexis C8, C10, C20, C30, CHP chargers

Location
• The equipment must be set up so that the mains switch, mains plug and all connections on the rear of the device are easily accessible.
• If you transport the equipment to another location take care to ensure that it is adequately secured and can never be damaged by being
dropped or by impacts on the equipment.
Fire hazard
• Never place naked flames (e.g. candles) near the equipment.
Humidity / heat sources
• Never expose the equipment to rain or a high level of humidity. For this reason do not install it in the immediate vicinity of swimming pools,
showers, damp basement rooms or other areas with unusually high atmospheric humidity.
• Never place objects containing liquid (e.g. vases or drinking glasses) on the equipment. Liquids in the equipment could cause a short circuit.
• Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
Connection – Synexis TS2 stationary transmitter, Synexis CHP, C20 charger
• The device can only be powered with the supplied external power adapter connected to a power outlet.
Connection - Synexis C8, C10, C30 chargers
• The equipment must be connected to a mains socket that has an earth contact.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
• Lay all connection cables so that they do not present a trip hazard.
• Whenever working on the equipment switch off all inputs and outputs to the power supply.
• Check whether the connection figures comply with the existing mains supply. Serious damage could occur due to connecting the system to
the wrong power supply. An incorrect mains voltage could damage the equipment or cause an electric shock.
• Please note that different operating voltages require the use of different types of power cable and plugs.
Please refer to the following table:
Voltage Power plug according to standard
110 - 125 V UL817 and CSA C 22.2 no 42.
220 - 230 V CEE 7 page VII, SR section 107-2-D1/IEC 83 page C4.
240 V BS 1363 (1984): "Specification for 13A fused plugs and
switched and un-switched socket outlets."
• If the equipment causes a blown fuse or a short circuit, disconnect it from the mains and have it checked and repaired.
• Do not hold the mains cable with wet hands. There must be no water or dust on the contact pins. In both cases you could receive an
electric shock.
• The mains cable must be firmly connected. If it is loose there is a fire hazard.
• Always pull out the mains cable from the mains and/or from the equipment by the plug – never by the cable. The cable could be damaged and
cause an electric shock or fire.
• Do not use the equipment if the mains plug is damaged.
• If you connect defective or unsuitable accessories, the equipment could be damaged. Only use connection cables available from or
recommended by beyerdynamic.
• Do not connect more than six Synexis C8 or C10 chargers in one daisy chain.
Switching off - Synexis C8, C10, C30 chargers
• In order to switch off the device disconnect the power plug from the power socket.
Disconnect - Synexis C8, C10, C30 chargers
• For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
Ventilation - Synexis C8, C10, C20, C30 chargers
• Do not insert objects into the ventilation grilles or other openings. You could damage the equipment and/or injure yourself.
Maintenance
• Only clean the equipment with a slightly damp or dry cloth. Never use solvents as these damage the surface.
Trouble shooting and servicing
• Do not open the equipment without authorisation. You could receive an electric shock. There are no user-serviceable parts inside.
• Leave all service work to authorised expert personnel.
5