POSIFLEX FT-6315 User Manual
POSIFLEX FT-6315 User Manual

POSIFLEX FT-6315 User Manual

Fan free touch control desktop pos terminal

Advertisement

FT-6315
Fan Free Touch Control
Desktop POS Terminal
User's Manual
Rev.: Original
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this
manual. However, Posiflex will assume no liability for any technical inaccuracies or
editorial or other errors or omissions contained herein, nor for direct, indirect,
incidental, consequential or otherwise damages, including without limitation loss of
data or profits, resulting from the furnishing, performance, or use of this material.
This information is provided "as is" and Posiflex expressly disclaims any warranties,
expressed, implied or statutory, including without limitation implied warranties of
merchantability or fitness for particular purpose, good title and against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technologies, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from
web
sites:
http://www.posiflex.com
or
http://www.posiflex.com.tw
or
http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data
resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2007
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 16600900010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FT-6315 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for POSIFLEX FT-6315

  • Page 1 FT-6315 Fan Free Touch Control Desktop POS Terminal User’s Manual Rev.: Original FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class...
  • Page 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery and maybe also a sealed type Lead acid battery if the UPS battery option is ordered.
  • Page 3: Product Pictures

    INTRODUCTION PRODUCT PICTURES Front Views Detail inside front cover Side Views Part 3...
  • Page 4: Parts Identification

    Rear Views Detail inside back cover Please note that the picture for inside front and back cover is for reference only. The actual layout may disagree from this picture if there is any difference in model or options selected or in the system revision. Please follow the actual layout for cable connections in this case.
  • Page 5: Product Features

    13. LCD panel tilt adjust button 14. Power switch button 15. Acoustic vent 16. Back cover release button 17. Reserved back cover lockup screw hole 18. Back cover 19. External power connector for power adaptor 20. Power adaptor 21. Internal power connector 22.
  • Page 6 Brightness control by 2 push buttons in front side of base Durable resistive type touch panel that endures 35 million touches min. at same spot (leading edge Infra Red type optional) Spill proof water resistant structure allowing easy cleaning Easy maintenance construction Various I/O ports supported, including: 1.
  • Page 7 Option Items: Note: The underlined items in the following list means that option must be set prior to shipment from the factory. The rest items can be set by the dealers. DDR SDRAM memory expansion up to 2GB RS232 interface Infra-Red type touch panel durable for 50 million touches min.
  • Page 8: Installation Guides

    NON-USER-INSTALLABLE OPTIONS When the FT-6315 system is ordered with options like expanded system memory or side mount upgrade kit, the option(s) is (are) already installed in the system delivered. Therefore, no more installation is required.
  • Page 9 Use the cable supplied with the cash drawer (Part No. 21863018010) for connection to the CR port in FT-6315 system. This cable has a 6-pole plug at one end and an 8-pole plug at the other. The 8-pole plug should be inserted into the connector marked: “signal cable from POS Printer”...
  • Page 10: Side Mount Upgrade Kit

    INSTALLING BASE MOUNT KIT (OPTION) When the FT-6315 series is ordered with the base mount upgrade kit like customer display PD-2603/2603U, PD-308/308U or PD-7623 option, the customer display together with the pole for installing them to rear of base will be delivered in separate package from the system unit.
  • Page 11: Barcode Scanner (Option)

    Gently arrange the excessive length of this cable back in the hole and screw-fit it back to the position originally occupied by the cover as in the right picture. Please reserve the cover if there is chance to have the side mount kit removed in the future.
  • Page 12: Connecting Ac Power

    CONNECTING AC POWER The power supply operating voltage must be checked to support the city power supply specification and switch selected if necessary. This must be done WITHOUT any connection to the AC power. The operating voltage selection switch is located close to the power input connector in the main connection area inside the back cable cover.
  • Page 13 a system without preloaded OS is highly discouraged. Posiflex shall not be responsible for any technical support to questions arisen due to non-preloaded Part 13...
  • Page 14: Application Environment

    USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit at ALL times for the installation.
  • Page 15: Power On/Off

    connected there but found inoperable by such messages. Emergency treatment: The battery is constructed maintenance free and leakproof. It is well protected in FT system as long as the ambient temperature remains below 30 C and the ventilation of the FT system remains free. However, should any accident happen and the sulfuric acid from the battery spills on skin or clothing, wash immediately with water.
  • Page 16 LED will keep on flashing for few seconds before steady till the AC supply is stable. Power ON/OFF control The FT-6315 system implements electronic power control, such that the main power to the system may be controlled by many methods as below: 1. Hardware power switch 2.
  • Page 17: Display Issues

    Display Utility Driver The end user of the FT-6315 terminals is not supposed to install the utility drivers personally. If an optional preloaded OS is ordered, the required Part 17...
  • Page 18: Serial Ports - Com1/2/3/4

    driver will be already installed in the preloaded OS. However, the driver will always be available over our web site: http://www.posiflex.com FRONT COVER & OTHER INDICATORS At left part on the front side of base unit, there is a front cover. Pick it up at the bottom notch and the CF memory card reader slot and an USB port for user’s convenience will be accessible.
  • Page 19 Mouse Emulation The touch panel in FT system uses USB interface as standard. Only the optional InfraRed type touch panel of FT-6315 uses RS232 interface. When the touch driver is properly installed, this touch panel works exactly like a standard mouse for both interfaces. However, if the system is running under safe mode, most drivers are disabled in this mode and the touch panel calibration is therefore not guaranteed.
  • Page 20 enabled for Modem Ring Up or select the “Resume by Alarm” for Alarm Clock Wake Up. Save the configuration and exit the CMOS setup program. The Preset Power On Control will then be ready after a normal power off. For LAN wakeup, an operating caller system connected through LAN to the system is required.

Table of Contents