Function Setting List - JUKI SC-910N Instruction Manual

5. Function setting list

No Item
1 Soft start The number of sttches to be sewn at a low speed when the soft-
functon
start functon s used at the start of sewng.
0 : Soft-start functon s not operatve.
2 Materal end Materal end sensor functon (used n case of wthout panel).
sensor functon 0 : Materal end detecton functon s not operatve.
1 : After detectng materal end, the specfed number of
3 Thread trmmng Thread trmmng functon by materal end sensor (used n case
functon by of wthout panel).
materal end 0 : Automatc thread trmmng functon after detecton of ma-
sensor
1 : After detectng materal end, the specfed number of
4 Number of Number of sttches for materal end sensor (used n case of wth-
sttches for
out panel).
materal end
Number of sttches from detecton of materal end to stop of the
sensor
sewng machne.
5 Flicker reducing Flicker reducing function (If the hand lamp flickers).
functon
0 : Flicker reducing function is not operative.
1 : Less effectve / 8 : Hghly effectve
6 Bobbn thread Bobbn thread countng functon
countng
0 : Bobbn thread countng functon s not operatve.
functon
1 : Bobbn thread countng functon s operatve.
7 Unt of bobbn Unt of bobbn thread countng down
thread countng
0 : Count/10 sttches
*
down
1 : Count/15 sttches
2 : Count/20 sttches
8 Number of Sewng speed of reverse feed sttchng
rotaton of
*
reverse feed
sttchng
9 Thread Thread trmmng prohbtng functon (used n case of wthout panel).
trmmng
0 : Thread trmmng prohbtng functon s not operatve.
prohbtng
1 : Thread trmmng s prohbted.
functon
10 Settng of Poston of needle bar s specfed when the sewng machne
needle bar stop
stops.
poston when
0 : Predetermned lowest poston
the sewng
1 : Predetermned hghest poston
machne stops.
11 Click sound Click sound of key switch mounted on PSC is specified.
of key switch
0 : Click is not operative.
mounted on
1 : Click is operative.
PSC
12 Optnal swtch Swtchng of functon of optonal swtch.
functon 0 : No functon
selecton
1 : Needle up/down compensatng sttchng
2 : Back compensating stitching
3 : Functon of cancelng once reverse feed sttchng at the
4 : Thread trmmng functon
5 : Presser foot lftng functon
6 : One sttch compensatng sttchng
7 : Functon of smultaneously cancelng reverse feed sttch-
8 : Functon of neutral presser foot lftng changeover
13 Functon of Functon of prohbtng start of the sewng machne by bobbn thread countng
prohbtng start
0 : When countng s out (-1 or less) Functon of prohbtng
of the sewng
machne by
1 : When countng s out (-1 or less) Functon of prohbtng
bobbn thread
*
counter
2 : When countng s out (-1 or less), the sewng machne
14 Sewng counter Countng functon of sewng (number of completon of process)
0 : Sewng counter functon s not operatve.
1 : Sewng counter functon s operatve.
15 Number of tmes Number of tmes of detecton of run-out of bobbn thread reman-
of detecton of ng amount
run-out of bobbn
*
thread remanng
amount 1 to 19 : Number of tmes durng whch the sgnal s not made
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer's Manual and follow the instructions.
(Descriptions of setting in this list are the standard values at the time of delivery of DDL-9000A.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
Descrpton
sttches (No. 4) wll be sewn, and the sewng machne wll
stop.
teral end s not operatve.
sttches (No. 4) wll be sewn, and the sewng machne wll
stop and perform automatc thread trmmng.
(Output of solenod s prohbted. : Thread trmmer and wper)
end of sewng
ng at the start and end of sewng
start of the sewng machne s not operatve.
start of the sewng machne after thread trmmng s op-
eratve.
stops once. Functon of prohbtng start of the sewng
machne after thread trmmng s operatve.
0 : Functon of bobbn thread remanng amount s not
operatve.
even f run-out of bobbn thread remanng amount s
detected.
Settng range
0 to 9
(Sttches)
0/1
0/1
0 to 19
(Sttches)
0 to 8
0/1
0 to 2
150 to 3,000
(r.p.m.)
0/1
0/1
0/1
0 to 8
0 to 2
0/1
0 to 19
– 24 –
Indcaton of functon settng Ref. page
1 0
31
2 0
3 0
4 5
5 0
31
6 1
31
7 0
8 1 9 0 0
9 0
31
1 0 0
31
1 1 1 31
1 2 0
32
1 3 0
1 4 1
32
1 5 1