JUKI SC-910N Instruction Manual page 35

4 On-tmng of solenod for condensaton sttch (when condensaton sttch s performed by 1 sttch.)
(Functon settng No. 65)
Starting timing of solenoid for condensation of 1 stitch can be corrected by angle at the unit of 10˚.
6 5
5 On-tmng of solenod for condensaton sttch (when condensaton sttches are performed by 2 sttches
or more.) (Functon settng No. 66)
Starting time of solenoid for condensation of 2 stitches or more can be corrected by angle at the unit of 10˚.
6 6
6 Needle thread release functon (Functon settng No. 28)
Ths functon sets the number of sttches untl the clamped needle thread s held after the start of sewng
2 8
7 Thread draw-out/return solenod (Functon settng No. 89)
Ths functon sets whether the moton of draw-out/return solenod (LZ) s performed or prohbted.
8 9
8 Number of sttches of tenson release moton at the sewng start (Functon settng No. 100)
This function sets the number of stitches to make the tension release solenoid actuate at the sewing start.
1 0 0
!1 Neutral automatic presser lifting function (with AK device only) (Functionsetting No. 21)
Ths functon can automatcally lft the presser foot when the pedal s n the neutral poston.
Automatc lftng tme of the pedal depends on the automatc lftng tme after thread trmmng and when
the presser foot s automatcally lowered, t s automatcally lfted at the second neutral poston after t has
come off the neutral poston once.
2 1
!2 Function of changeover of compensating switch on the operation panel function (Function setting No. 22)
Functon of compensaton swtch on the operaton panel of CP-170 or IP-110 can be changed over to nee-
dle up / down compensatng sttchng or one sttch compensatng sttchng.
2 2
!3 Thread trimming motion condition (Function setting No. 25)
This function makes the thread trimming motion ineffective when depressing the back part of the pedal af-
ter DOWN detection position has been off by turning handwheel by hand or the like.
2 5
!4 Function of setting the holding force after stop (Function setting No. 26)
Functon to prevent the ncreased amount of reverse rotaton after stop when the machne has been used for
a long tme and the machne head torque has become lght. When the set value s ncreased, the preventon
effect becomes large. However, when the set value s excessvely ncreased, on the contrary, there s a dan-
ger that the machine normally rotates. Adjust the function while checking the motion of the needle bar.
2 6
!5 Function of setting the reaction force at the time of retry (Function setting No. 27)
Ths functon changes the magntude of the reversng force before movng to the retry moton.
2 7
Adjustng range
– 1 5
– 36 to 0 <1 / 10˚>
Adjustng range
– 1 5
– 36 to 0 <1 / 10˚>
Settng range : 0 to 30 sttches
1
0 : Moton s neffectve.
0
1 : Functon s effectve.
Settng range : 0 to 9 sttches
0
0 : off Functon of neutral automatc presser lftng s not operatve.
0
1 : on Selecton of functon of neutral automatc presser lftng
0 : Needle up / down compensatng sttchng
0
1 : One sttch compensatng sttchng
0 : Thread trmmng moton s effectve.
1
1 : Thread trmmng moton s prohbted.
Settng range : 0 to 9
0
Settng range : 1 to 100
5 0
1 : Less reversng force to 100 : More reversng force
– 33 –