Main Frame Assembly - ProSpot Fitness P-500 Owner's Manual

STEP # 1: MAIN FRAME ASSEMBLY
1.
Place the two Base Rails (1 & 2) opposite each other in the center of the assembly area as shown in the
lllustration. Place the Lower Cross Brace (3) between the two Base Rails (1 & 2) so that the side pre-drilled holes
of the Base Rails (1 & 2) align with the end holes of the Lower Cross Brace (3).
2.
Carefully thread the Cross Brace Wire Harness (8) through the corresponding side pre-drilled holes of the Base
Rails (1 & 2) then pull the Wire Harness (8) out of the top holes of the Base Rails (1 & 2).
3.
Attach the two Base Rails (1 & 2) to the Lower Cross Brace (3) using two Cross Brace Backing Plates (13), four
bolts (22), eight washers ('18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
4.
Attach the Right Upright Guidepost Assembly (7, 10, 23\ to the Right Base Rail (2) using two Upright Support
Plates (6), four bolts (22), eight washers (18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
5.
Attach the Left Upright Guidepost Assembly (9, 12, 23) to the Left Base Rail (1) using two Upright Suppurt Plates
(6), four bolts (22), eight washers (18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
6.
Slide the VKR Sliding Adjuster ('111) up onto the left one of Rear Uprights (4) as shown. Pull the handle on the
screw down pull pin (68) previously installed. This will allow the VKR Sliding Adjuster (11'l) to slide up. Release
the pin to lock in place and secure by turning knob clockwise.
7. Attach the VKR Frame (59) to the VKR Sliding Adjuster (111) using two bolts (110) four washers (18) and two
nuts (20) as shown. Tighten the bolts securely.
8.
Attach the left Rear Upright (4) to the Lower Cross Brace (3) and lhe Cross Brace Backlng Plate (13) attached on
the Left Base Rail (1) using two bolts (22), four washers (18) and two nuts (20) as shown. HAND TIGHTEN the
bolts at this time.
9.
Slide the Chin-up Bar Sliding Adjuster (1 12) up onto the right one of Rear Uprights (4) as shown Pull the handle
on the screw down pull pin (68) previously installed. This will allow the Chin-up Baf S id ng Adtuster (1 '12) to slide
up. Release the pin to lock in place and secure by turning knob clockwise.
10. Attach the Chin-up Bar(61) tothe Chin-up BarSliding Adjuster (1 1 2) using two bolts ( 1 1 0) fourwashers ('18) and
two nuts (20) as shown. Tighten the bolts securely.
1 1 . Attach the right Rear Upright (4) to the Lower Cross Brace (3) and the Cross Brace Backrng Plate (13) attached
on the Right Base Rail (2) using two bolts (22), four washers (18) and two nuts (20) as sholvn HAND TIcHTEN
the bolts at this time.
12. Plug together both of the Cross Rail Wire Harness (8) to lower ends of the Spiral Signal Cables (46) located just
under the perforated Slider Shields on back of the Screen Panels (23).
'13. Attach one Pulley
Support Frame (17) to the Left Upright Guide Post (12) using two bolts (22). four washers (18)
and two nuts (20). HAND TIGHTEN the bolts at this time.
'14. Carefully thread the Left Weight Bar Knuckle (44) up through
the rectangular cutout in the Pulley Support Frame
(17). Carefully flex the Left Weight Bar Cables (24) so that the cables are between the iwo puliey support plates
and insert into the grooves of each corresponding pulleys. Be sure that the cables are straight and uncrossed
and pulleys move smoothly.
15. Attach the two small plastic pipes (15) to the Pulley Support Frame (17) using two bolts (34). four washers (38)
and two nuts (35) as shown. Tighten the bolts securely.
16. Repeat steps 11-13 on the right side of the PROSPOTlirrressrM
P-500.
'17. Attach the two Rear Uprights (4) and the Top Beam (60) to the two Pulley
Support Frames (17) using four bolts
(28), eight washers (18) and four nuts (20) as shown. HAND TIGHTEN the bolts at this time.
18. Attach the Pec Deck Support Post (16) and the Electronic Box Locating Plate (5) to the Lower Cross Brace (3)
using two bolts (22), four washers (18) and two nuts (20) as shown. HAND TIGHTEN the bolts at this time.
19. Attach the Pec Deck Support Post (16) to the Top Beam (60) using a bolt (51), two washers (18) and a nut (20)
as shown. HAND TIGHTEN the bolts at this time.
20. Tighten all bolts and nuts used for assembly in previous steps.
21. Insert both of the Guide Rods (77) into each of the Guide Rod Cups (74) located on the lower end of the Pec
Deck Support Post (16). Slide the Weight Stacks (67) onto the Guide Rods (77) and carefully slide them to the
bottom. Slide the Weight Top Plate Assembly (63, 70) onto the Guide Rods (77) and guide them down so that
they rest on top of the Weight Stacks (67). Insert two Allen bolts (71) into the threaded holes in the Guide Rod
Cup Pockets of the Pec Deck Support Post (16). Tighten securely.