Page 1
R R O O P P O O T T Model P-600 ® Owners Manual Table of Contents Assembly Instructions……………………..…………………………..……..2-11 Use and Operation of Your PROSPOTfitness® Product….………………..12-16 Periodic Maintenance of your PROSPOTfitness® Product……………….… 17 Parts List…………………………………………………….…………….…18-19 Trouble-Shooting……………………………………………………………..20-21 Warranty & Contact Information……………………………………….…….…22...
Page 2
6’x 6’. The barbell is approximately 7’ long. Locate your PROSPOTfitness® P-600 away from any source of water. Do not allow any liquid to be near the machine or spilled on any electrical part. Do not insert any object into the electrical box.
Page 3
Instructions for Assembly of the ProSpotfitness® P-600 Step #1 MAIN FRAME ASSEMBLY 1. Place the Base Rails (6,7) opposite each other in the center of the assembly area as shown in the illustration. Place Lower Frame Cross Brace (14) between the two Base Rails (6,7) so that the side, pre-drilled holes of the Base Rails align with the holes of the Lower Frame Cross Brace.
Page 4
STEP #2 – SENSOR WEIGHT BAR INSTALLATION 1. Standing in front of the ProSpot Fitness P-600, slide one end and then the other end of the Sensor Weight Bar (37) into the Knuckles (55,56,57). Ensure that barbell cables are not crossed or twisted. Slide the Knuckles onto the bar until they rest snugly against the pre-installed Sensor Retaining Collars (50,51).
Page 5
7. Place Side Weight Stack Covers (73) so that the holes on the cover align with the holes on the tabs of the Upper Frame and bottom Side Base Rails (6,7). Secure with bolts #113, flat washers #136 and nuts #130. 8.
Page 12
!!Read!! This Page Before Using Your ProSpotfitness ® Product Safe Use of Your ProSpotfitness® Product CAUTION: This machine involves the risk of possible injury by its user. THE FOLLOWING RULES SHOULD BE CARFULLY FOLLOWED: • Consult a physician or other healthcare provider before beginning an exercise program.
Page 13
Push in the push-release lever with your thumb and move the Spot Blocks so that they are touching the top of the slider locking block (the black block with the ProSpot Fitness® logo on it). Release the push-release lever to lock the Spot Block in place.
Page 14
Make certain the barbell is level before loading weight plates. Level the barbell by raising up one end of the barbell until it is level. (The P-600 is equipped with a ratcheting feature that allows the barbell to be manually raised from side-to-side.) Or, level the barbell by grasping it with both hands, making sure the fingertips make contact with the touch sensor strip.
Page 15
Frames can be positioned for use either together or singly. See Exercise List for a few specific exercise suggestions. Place barbell into the notched grooves on top of the P-600. This secures the barbell and keeps it out of the way during cable use.
Page 17
Maintenance of ProSpotfitness® Product Our products are made of durable materials and have been factory tested to assure proper function and reliability. Along with our Equipment Warranty, this gives the owner of our product the confidence of a long lasting relationship with ProSpotfitness® Inc. Our systems are designed in a way to allow easy replacement of parts both mechanical and electrical if the need should ever arise.
Page 18
ProSpotfitness® PHL-600 Parts list Description Description Item # Quan. Item # Quan. Right Front Guide Post Weight Bar Sensor Retaining Collar Btm. Half Left Front Guide Post Sensor Collar Brass Contact Pin Front Guide Post Upright Support Plate Sensor Collar Brass Contact Pin Spring Right Rear Locking Post Sensor Collar Set screw M6...
Page 19
Description Description Item # Quan. Item # Quan. Side Weight Stack Pulley Bracket 151 Rear Cover (For Optional Weight Stack) Side Weight Stack Cable Rear Cover Link Plate Weight Stack Cable Jam Nut 1/2"-13 Cable Pull Handle 104 Plastic Insert Cap 63.5mm 157 Snap Link 105 Logo Foot End Cap 63.5mm 158 Round Link Ring...
Page 20
Trouble-Shooting How the Patented ProSpot System works: Starting from the Computer Brain, a signal is sent from the left & right side, thru the L & R Grey Base Frame Wire Harness (white lead), to the Spiral Cord Harness (brown lead), to the Slider Block Cable Knuckle connector, to inside Barbell Cable to the Sensor on the Barbell.
Page 21
a. If no contact, adjust Sensor Collar closer. (See Weight Bar / Cable-Knuckle Assembly Diagram) Trouble Shooting (con't) Symptom: Sensor Weight Bar will not unlock. Solution: 1. Remove #10 Inspection covers on both sides to gain access to #93 Spiral cord wire Harness.
Page 22
1325 Oakbrook Drive, Suite E Norcross, GA 30093 Office (770) 446-9299 (770)-446-7213 Contacting ProSpot Fitness Technical Support: Our Service Department can be reached M-F 9-5 pm EST. Or e-mail us: support@prospotfitness.com If ordering replacement parts, please refer to the Owners Manual for part numbers and description.