Polycom SpectraLink 6000 System Installation Manual
Outdoor base station
Hide thumbs
Also See for SpectraLink 6000 System:
- Owner's manual (74 pages) ,
- Maintenance and diagnostics (58 pages) ,
- Facility preparation (41 pages)
Related Manuals for Polycom SpectraLink 6000 System
Summary of Contents for Polycom SpectraLink 6000 System
-
Page 1: Base Station
Installing the Outdoor Base Station SpectraLink 6000 System July 2008 Edition 1725-36127-001 Version F... -
Page 2: Copyright Notice
All rights reserved under the herein shall be deemed to be a warranty International and pan-American by Polycom for any purpose, or give rise copyright Conventions. to any liability of Polycom whatsoever. No part of this manual, or the software... -
Page 3: About This Guide
This document covers the installation of the Outdoor Base Station in a variety of situations. It supplements the installation documentation for the SpectraLink 6000 System using either the SpectraLink 6300 MCU or the SpectraLink 6100 MCU. Polycom Corporation Model Numbers... - Page 4 Installing the Outdoor Base Station For Technical Support: technicalsupport@polycom.com For Knowledge Base: http://www.polycom.com/usa/en/support/voice/voice.html For Return Material Authorization: rmacoordinator@polycom.com 1725-36127-001-F.doc...
-
Page 5: Table Of Contents
Contents About this Guide ..........3 Polycom Corporation Model Numbers Related Documents Contacting Polycom Installing Flush Against a Wall or Hard Ceiling ..6 Installing on an I-Beam ........8 Installing on a Light Pole or Electrical Pole ..10 1725-36127-001-F.doc... -
Page 6: Installing Flush Against A Wall Or Hard Ceiling
Installing Flush Against a Wall or Hard Ceiling Items provided: Outdoor enclosure, Base Station Items needed: 4 anchor bolts (length and type depends on wall or ceiling material Base Station is being mounted to) 1. Mark and drill four holes into the wall or ceiling, using the mounting flanges of the outdoor enclosure as a guide. - Page 7 Installing Flush Against a Wall or Hard Ceiling 4. Crimp an RJ45 onto the Base Station cable using the same wiring guide as the indoor Base Station. 5. Plug the RJ45 into the RJ48C connector. Mounting hole RJ48C connector 6. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the wall or ceiling.
-
Page 8: Installing On An I-Beam
Installing on an I-Beam Items provided : Outdoor enclosure, Base Station Items needed : 4 – “Caddy” or “B-Line” 3/8” Beam Clamps 4 – 1/2” long 1/4” x 20 bolts 4 – 2” long 1/4” x 20 bolts 4 – 1/4” x 20 nuts 1. - Page 9 Installing on an I-Beam 7. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the I-beam. The Base Station should fit tightly between the foam blocks. 8. Screw the outdoor enclosure lid back onto the enclosure. 1725-36127-001-F.doc...
-
Page 10: Installing On A Light Pole Or Electrical Pole
Installing on a Light Pole or Electrical Pole Items provided: Outdoor enclosure, Base Station Items needed: 4 - “Caddy” or “B-Line” 3/8” beam clamps 2 - EOG 100 or equivalent band clamps 1. Attach one band to the top flange of the outdoor enclosure using two beam clamps (see the figure below). - Page 11 Installing on a Light Pole or an Electrical Pole 7. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the pole. The Base Station should fit tightly between the foam blocks. 8.
- Page 12 PN: 1725-36127-001-F.doc...
Need help?
Do you have a question about the SpectraLink 6000 System and is the answer not in the manual?
Questions and answers