Related Manuals for Hoshizaki JWE-2400CUA-L-25B
Summary of Contents for Hoshizaki JWE-2400CUA-L-25B
- Page 1 JWE-2400CUA-L-25B DISHWASHER JWE-2400CUA-R-25B INSTALLATION MANUAL FOR QUALIFIED INSTALLER ONLY L2J002111 (011911)
- Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write, or send an e-mail message to the Hoshizaki Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
IMPORTANT This manual should be read carefully before the product is installed and operated. Only qualified service technicians should install, service, and maintain the product. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that may be necessary. - Page 4 [e] ADJUSTMENT ------------------------------------------------------------------------------------ 17 [f] LOWER WASH SPRAY ARM PRESSURE AND FLOW RATE ----------------------- 17 9. RELOCATION ----------------------------------------------------------------------------------------- 18...
-
Page 5: Important Safety Information
Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. -
Page 6: Moving
1. MOVING WARNING Top Panel When handling the unit (unloading from pallet, moving, installing), do not hold the service panel or top panel, or the service Service Panel panel will open. Hold the parts indicated by arrows only. * Do not remove the shipping tape securing the service panel until the end of installation. * Be careful not to damage the piping projecting from the bottom of the unit. -
Page 7: [A] Shipping Tape
7KH ORFDWLRQ VKRXOG SURYLGH D ¿UP DQG OHYHO IRXQGDWLRQ IRU WKH XQLW WR DYRLG the risk of water leaks or injury caused by overturn or fall. 6. Avoid a site where dripping is not allowed. The unit may drip water onto the ÀRRU $PELHQW WHPSHUDWXUH VKRXOG EH ZLWKLQ WR ƒ) WR ƒ& 2SHUDWLRQ RI the unit for extended periods outside of this normal temperature range may... -
Page 8: [B] Checks Before Installation
[b] CHECKS BEFORE INSTALLATION 1) Check the exterior including the front panel and service panel for damage. &KHFN WKH LQWHUQDO SDUWV LQFOXGLQJ WKH VSUD\ DUPV DQG ¿OWHUV IRU GDPDJH RU FORJJLQJ 3) The accessories except the rack are provided in the carton. Check that all the DFFHVVRULHV OLVWHG LQ WKH LQVWUXFWLRQ PDQXDO VHH ³ >G@ $&&(6625,(6´ DUH LQFOXGHG and not damaged. -
Page 9: [E] Connection To A Dishtable
the plastic bag, and tie it with the opening facing down. 5H¿W WKH IURQW SDQHO LQ LWV FRUUHFW SRVLWLRQ Cable Cover (S) [accessory] 2SHUDWLRQ %R[ Top Panel Bolt (stainless Cable Cover (S) steel 4x8) * Remove from Hook top panel Square Hole Cable Cover (L) 2SHUDWLRQ %R[... -
Page 10: [F] Splash Guard
3) Hook the dishtable on the wash tank. Drill a hole Dishtable in the wash tank to match the mounting hole in the dishtable. Drill a hole Dishwasher IMPORTANT To prevent possible corrosion, do not leave any shavings after drilling the hole in the wash tank. -
Page 11: Ventilation
2) Put the cable of the accessory table limit switch through the cable hole in the dishtable, and secure the switch with the bolts provided. 8.1" (206mm) 0.8" (20mm) Three 0.24" (6mm) Cable Hole Mounting Holes 1.34" (34mm) 4.5" 3.6" (114mm) (91mm) 2.93"... -
Page 12: Water Supply And Drain Connections
3. To use a gas water heater, thoroughly read its instruction manual. Ensure adequate air intake and exhaust systems and exhaust hoods in accordance with applicable national, state, and local regulations for the type and capacity of the heater to prevent dangerous conditions due to lack of oxygen and toxic gas generation. -
Page 13: [D] Strainer
([WHUQDO ¿OWHUV DQG VWUDLQHUV PD\ EH UHTXLUHG GHSHQGLQJ RQ ZDWHU TXDOLW\ &RQWDFW \RXU local Hoshizaki distributor for recommendations. * Sediment, silica, chlorides or other dissolved solids may lead to a recommendation for SDUWLFXODWH ¿OWUDWLRQ RU UHYHUVH RVPRVLV WUHDWPHQW... -
Page 14: [E] Hot Water Supply Connection
[e] HOT WATER SUPPLY CONNECTION WARNING To reduce the risk of burns, the hot water supply line must be thermally LQVXODWHG +RW ZDWHU DURXQG ƒ) ƒ& ZLOO ÀRZ LQVLGH * Where there is a risk of water hammer, it is recommended to install a water hammer arrestor between the dishwasher and water heater. -
Page 15: Electrical Connection
* If the drain pipe running from side to side at the bottom is long and coming out from under the unit, the drain pipe weight may cause deformation of the wash tank bottom. In such case, insert the accessory hook - drain into the square hole in the bottom of the unit, secure with the bolt provided, and use a band to hold the drain pipe. - Page 16 (OHFWULFDO 6SHFL¿FDWLRQV $OVR 5HIHU WR WKH 'LVKZDVKHU 1DPHSODWH AC Supply Voltage Maximum Breaker/Fuse Size Minimum Circuit Ampacity Dishwasher 70A Dishwasher 70A 208 - 230V / 60Hz / 3Ph Booster Tank 80A Booster Tank 80A * Usually an electrical permit and services of a licensed electrician are required. * The maximum allowable voltage variation is ±10 percent of the nameplate rating.
-
Page 17: Phase Reversal Check
5) Connect the terminals to the terminal blocks. Check the wire colors against the wiring label attached inside the front panel to prevent miswiring. The terminal block on the left is for the dishwasher, and the one on the right is for the booster tank. 6) Reattach the control box cover and the front panel. -
Page 18: Detergent/Rinse Aid Feeder
Any feeders provided by a detergent supplier must be installed as described below. For electrical and plumbing connections, follow the instructions in this manual and the manual supplied with the feeder. Consult with the detergent supplier or an authorized Hoshizaki service company for further details. -
Page 19: [C] Rinse Aid Inlet
1RWH 'R QRW LQVWDOO WKH GHWHUJHQW LQOHW WR WKH ULQVH VSUD\ DUP VLGH ,I WKH GHWHUJHQW LQOHW cannot be installed to the side of the tank, drill a mounting hole in the entrance of the wash compartment or the back of the top panel. Within This Area Rinse Spray Arm Mounting Hole... -
Page 20: Trial Run
IMPORTANT 1. Be sure to use detergent and rinse aid feeders with protective fuses. 2. Ensure the power supply capacity of 208 to 230V AC, 1A or less, and use insulated terminals to connect the feeders to the terminal block. 7KH ULQVH DLG IHHGHU LV QRW VLJQDOHG WR VWDUW GXULQJ WKH DXWR ¿OO F\FOH HYHQ LI the rinse pump runs. -
Page 21: [B] Preparing Hot Water Supply
[b] PREPARING HOT WATER SUPPLY 1) If the optional drain valve for low temperature conditions is installed, close the drain valve provided to prevent freezing. 2SHQ WKH ZDWHU VXSSO\ YDOYH 3) Follow the instructions in the water heater’s instruction manual. [c] FINAL CHECKS 1) Are independent three-phase 208 to 230V disconnects used? 2) Is the voltage tap switch on the right side of the control box set to the proper voltage? -
Page 22: [D] After Trial Run
[e] ADJUSTMENT If any adjustment is required to the wash or rinse cycle time or temperature setting, contact an authorized Hoshizaki service company. [f] LOWER WASH SPRAY ARM PRESSURE AND FLOW RATE 7KH SUHVVXUH DQG ÀRZ UDWH RI WKH ORZHU ZDVK VSUD\ DUP DUH DGMXVWDEOH LQ WKUHH OHYHOV E\ the damper located on the lower wash pipe. - Page 23 Lower Wash Pipe Damper Screw Lower Wash Spray Arm Damper Damper Scale: Lower Wash Spray High Arm Jet Force: 9. RELOCATION WARNING 1. Make sure the power supply is off before making any electrical connections to prevent possible electric shock. Lockout/Tagout to prevent the power from being turned back on inadvertently.