Table of Contents
Advertisement
2
RESET BUTTON
..
See "Motor
Specifications and
Electrica
Requirements"
section.
"Motor
Safety
Protection."
NOTE:
When bevel crosscutting, attach facing so that it
extends to the right of the miter gauge and use the miter
gauge in the groove to the right of the blade.
3
ELEVATION
HANDWHEEL...
elevates or lowers the
blade. Turn clockwise
to elevate..,
counterclockwise
to lower.
NOTE:
WHEN THE BLADE
IS TILTED
TO 45 ° , IT
CANNOT
BE LOWERED
ALL
THE
WAY BELOW
THE TABLE. IT WILL PROJECT APPROX. 1/2 IN
4
TILT
HANDWHEEL
...
tilts
the blade for bevel
cutting.
Turn
clockwise
to
tilt
toward
left
...
counterclockwise to tilt toward right.
When the blade is tilted to the LEFT as far as it will go,
it should be at 45 ° to the table and the bevel pointer
should point 45 °.
NOTE:
There are LIMIT
STOPS inside the saw which
prevent the blade from tilting beyond 45 ° to the LEFT
and g0° to the RIGHT.
(See "Adjustments"
section
"Blade Tilt. or Squareness of Blade to Table").
7
5
RIP FENCE
...
is locked in place by tightening the
lock knob. To move the fence, oose_ the lock knob
and grasp the fence with one hand at the front.
8
Holes are provided in the rip fence for attaching a wood
facing when using the dado head, or molding head.
\
\
\
\
BLADEGUARD
must always he in place and working
properly
for
all thru-sawing cuts. That is, all cuts
whereby
the
blade cuts completely
through
the
workpiece.
To remove the guard for special operations, loosen the
wmgscrews and move spreader awm/ from saw and lift
upwards. DO NOT DISTURB
THE SETTING
OF THE
REX NUTS.
When replacing
the guard, make sure the spreader is
moved toward
front
of saw so that wingscrews are at
end
of
slots.
TIGHTEN
THE
WlNGSCREW_S
SECURELY.
TABLE INSERT is removable for removing or installing
blades or other cutting tools..
Select a piece of smooth straight wood appro×, 3/4 in,
thick and the same size as the rip fence.
Attach
it to the fence with
three
Round Head # f0
Wood Screws 2 in, long. To remove the facing, loosen
the screws, slide the facing forward and pull the screws
throu_
the round holes.
ANTIKICK BACK
PAWLS
WOOD FACING
\
# 1o WOOD SCREWS
6
MITER
GAUGE
..
head is locked in position
for
crosscutting
or mitering
by tighting
the lock
knob,
ALWAYS
LOCK IT SECURELY
WHEN IN USE.
Notches are provided in the miter gauge for attaching
an AUXILIARY
FACING
to make it easier to cut long
pieces, Be positive facing does not interfere
with the
proper operation
of the sawblade guard.
Select a suitable piece of smooth straight wood..,
drill
two holes through it and attach it with screws.
WARNING:
FOR YOUR OWN SAFETY,
TURN SWITCH
"OFF"
AND
REMOVE
PLUG FROM POWER SOURCE
OUTLET BEFORE REMOVING
INSERT.
A, Lower the blade below the table surface.
B. Loosen screw.
C.
Lift antikickback pawls.
D. Lift insert from front end, and pull toward front of
saw.
NEVER
OPERATE
THE SAW WITHOUT
THE PROPER
INSERT
IN
PLACE.
USE
THE SAW BLADE
INSERT
WHEN
SAWING
.,.
USE THE COMBINATION
DADO
MOLDING
INSERT WHEN DADOING
OR MOLDING.
\
16
Hide quick links:
Advertisement
Table of Contents
