Lun Configurations On The Raid Storage Systems - HP XP P9500 Configuration Manual

Example 6 Using Raidscan to display TID and LUN for Fibre Channel devices
C:\>raidscan -pd hd6 -x drivescan hd6
Harddisk 6... Port[ 2] PhId[ 4] TId[ 3] Lun[
Port[CL1-J] Ser#[
HORC = SMPL
RAID5[Group
PORT# /ALPA/C,TID#,LU#.Num(LDEV#....)...P/S, Status,Fence,LDEV#,P-Seq#,P-LDEV#
CL1-J / e2/4,
CL1-J / e2/4,
CL1-J / e2/4,
CL1-J / e2/4,
CL1-J / e2/4,
CL1-J / e2/4,
CL1-J / e2/4,
Specified device is LDEV# 0014
In this case, the target ID indicated by the raidscan command must be used in the configuration
definition file. This can be accomplished using either of the following two methods:
Using default conversion table. Use the TID# and LU# indicated by the raidscan command in
the HORCM configuration definition file (TID=29 LUN=5 in
display TID and LUN for Fibre Channel
Changing default conversion table. Change the default conversion table using the
HORCMFCTBL environmental variable (see
default Fibre conversion
the default Fibre conversion
Example 7 Using HORCMFCTBL to change the default Fibre conversion table
C:\> set HORCMFCTBL=X
C:\> horcmstart ...
:
:
Result of "set HORCMFCTBL=X" command:
C:\>raidscan -pd hd6 -x drivescan hd6
Harddisk 6... Port[ 2] PhId[ 4] TId[ 3] Lun[
PORT# /ALPA/C,TID#,LU#.Num(LDEV#....)...P/S,Status,Fence,LDEV#,P-Seq#,P-LDEV#
CL1-J /
CL1-J /
CL1-J /
CL1-J /
CL1-J /
CL1-J /
CL1-J /
Specified device is LDEV# 0014

LUN configurations on the RAID storage systems

The RAID storage systems (XP1024/XP128 Disk Array and later) manage the LUN configuration
on a port through the LUN security as shown in the following figure.
52 Fibre-to-SCSI address conversion
30053] LDEV#[
HOMRCF[MU#0 = SMPL MU#1 = SMPL MU#2 = SMPL]
1- 2] SSID = 0x0004
29, 0.1(9).............SMPL
29, 1.1(10)............SMPL
29, 2.1(11)............SMPL
29, 3.1(12)............SMPL
29, 4.1(13)............SMPL
29, 5.1(14)............SMPL
29, 6.1(15)............SMPL
table") (TID=3 LUN=5 in
table").
Port[CL1-J] Ser#[
HORC = SMPL HOMRCF[MU#0 = SMPL MU#1 = SMPL MU#2 = SMPL]
RAID5[Group 1- 2] SSID = 0x0004
e2/0, 3, 0.1(9).............SMPL
e2/0, 3, 1.1(10)............SMPL
e2/0, 3, 2.1(11)............SMPL
e2/0, 3, 3.1(12)............SMPL
e2/0, 3, 4.1(13)............SMPL
e2/0, 3, 5.1(14)............SMPL
e2/0, 3, 6.1(15)............SMPL
5] [HITACHI ] [OPEN-3
14(0x00E)]
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
devices").
Example 7 "Using HORCMFCTBL to change the
Example 7 "Using HORCMFCTBL to change
'X' is fibre conversion table number.
Start of HORCM.
5] [HITACHI
30053] LDEV#[ 14(0x00E)]
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
---- ------ ----, -----
]
----
----
----
----
----
----
----
Example 6 "Using Raidscan to
] [OPEN-3 ]
----
----
----
----
----
----
----