Page 2 Company. The information contained in this document is subject to change without notice. NEXT Hewlett-Packard makes no warranty of any kind with regard to this printed material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Page 3 YPOGRAPHICAL ONVENTIONS The following typographical conventions are used in this manual: Emphasis: Denotes important information. : Keys on the jukebox. Keycap NEXT Computer Output: Information displayed in the display window and screen menu items that you can select. WARNING:Warnings call attention to a procedure or practice that could result in personal injury if not correctly performed. PREVIOUS Do not proceed until you fully understand an meet the required conditions.
Page 4 ANUAL This user’s guide includes: NEXT Chapter 1 set-up information for the HP SureStore Optical 125ex optical jukebox Chapter 2 information about choosing and using optical disks PREVIOUS Chapter 3 features description, operating instructions, and troubleshooting information Appendix A supplies and customer support JUMP Appendix B operating this jukebox on a SCSI bus...
Page 5 ONTENTS &RQWHQWV &RQWHQWV ETTING UP THE UKEBOX SING PTICAL ISKS...
Page 6 ONTENTS PERATING THE UKEBOX...
Page 7 ONTENTS A: S PPENDIX UPPLIES AND USTOMER UPPORT B: O SCSI B PPENDIX PERATING UKEBOX ON A...
Page 8 ONTENTS C: S PPENDIX AFETY AND EGULATORY NFORMATION...
Page 9 ONTENTS...
Page 10: Table Of Contents
IGURES Figures Rear Panel Features ........1-4 Figure 1-1: The Mailslot Shipping Bracket .
Page 11 ABLES Tables Configurations ..........3-23 Information Logs .
Page 12 ETTING UP THE UKEBOX 1Setting up the Jukebox ETTING P THE UKEBOX This chapter tells you how to connect the jukebox to your computer. Follow the unpacking instructions printed on the outside of the shipping carton before you complete the steps given in this chapter. NEXT NOTE: “Jukebox”...
Page 13 ETTING UP THE UKEBOX HAT YOU NEED FOR SETTING UP THE JUKEBOX • power cord (included) • SCSI terminator (included) • 68-pin, high density SCSI cable of desired length NEXT • single-ended or low-voltage differential SCSI host adapter with at least two available addresses (at least three avail- able addresses if you are installing one jukebox with two drives).
Page 14 ETTING UP THE UKEBOX HOOSING A OCATION Before setting up your jukebox, choose the proper environment based on the following recommendations: • temperature range between 65-75º F (18-24º C). The maximum operating temperature range is 50-104º F (10-40º) • away from sources of particulate contamination such as printers, scanners, frequently-used doors and walkways, NEXT supplies that collect dust, and smoke-filled rooms.
Page 15: Figure 1-1: Rear Panel Features
ETTING UP THE UKEBOX DENTIFYING ANEL EATURES Refer to Figure 1-1 and the text on the next page to identify parts and learn their functions. Figure 1-1: Rear Panel Features NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 16 ETTING UP THE UKEBOX The numbers below correspond to the numbers in Figure 1-1 on the previous page. Table 1-1: Power receptacle Used to connect the power cord to the jukebox. Standby/on switch The ON position applies power to the robotics and electronics in the jukebox.
Page 17 ETTING UP THE UKEBOX EMOVING THE AILSLOT HIPPING RACKET AND HECKING EMOVAL OF THE HIPPING CREW The jukebox is shipped with a plastic bracket inserted into the mailslot to prevent damage to the mailslot during ship- ping. A shipping screw is installed through the bottom of the chassis to restrain the cartridge picker. NEXT To remove the mailslot bracket, do the following.
Page 18: Figure 1-2: The Mailslot Shipping Bracket
ETTING UP THE UKEBOX Figure 1-2: The Mailslot Shipping Bracket NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 19 ETTING UP THE UKEBOX NOTE: When shipped, a wire links the shipping screw to the packing material on the bottom of the jukebox. The screw should have been removed when the bottom packing material was removed. Check that the shipping screw was removed by doing the following: 3.
Page 20: Figure 1-3: Location Of The Shipping Screw
ETTING UP THE UKEBOX Figure 1-3: Location of the Shipping Screw NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 21 ETTING UP THE UKEBOX SCSI C ONNECTING THE ABLE TO THE UKEBOX The jukebox can be connected to either a single-ended or low-voltage differential SCSI bus. The connectors are high- density 68-pin. When connecting to a single-ended SCSI bus, and because the drives are “fast SCSI” you have a maximum of 9.8 feet NEXT (3 metres) for the entire bus.
Page 22 ETTING UP THE UKEBOX ONNECTING THE UKEBOX AS THE ERIPHERAL The default IDs for the jukebox are as follows. Check to see if there will be any conflicts in this installation. Autochanger (jukebox robotics) = 3 Drive 1 = 4 NEXT Drive 2 = 5 (if installed) NOTE:...
Page 23: Figure 1-4: Connecting The Jukebox As The Only Peripheral
ETTING UP THE UKEBOX Figure 1-4: Connecting the Jukebox as the Only Peripheral NEXT PREVIOUS JUMP CONTENTS 3. Connect a SCSI cable between one of the SCSI ports on the jukebox with a SCSI port on your host computer (see “3”...
Page 24 ETTING UP THE UKEBOX SCSI ONNECTING THE UKEBOX WITH THER ERIPHERALS Connecting this jukebox with other peripherals on the bus is shown in Figure 1-5. Important: Other devices on the same bus as this jukebox will affect jukebox performance. Consider the following issues if you are deciding NEXT whether to connect other devices onto the same bus.
Page 25: Figure 1-5: Connecting The Jukebox With Other Scsi Peripherals
ETTING UP THE UKEBOX Important: Although this jukebox connects to a 68-pin SE/LVD “wide” SCSI bus and host adapter, the jukebox and its optical drives use a 50-pin “narrow” SCSI bus internally. See Appendix B for a discussion of SCSI buses. Do not force “wide”...
Page 26 ETTING UP THE UKEBOX Drive 1 = 4 Drive 2 = 5 (if installed) NOTE: If you determine that there are conflicts among SCSI IDs that are currently in use by your system and peripherals you will be placing on the bus, plan to do the following steps, as they apply to your situation. •...
Page 27 ETTING UP THE UKEBOX ONNECTING OWER DJUSTING URNING UKEBOX NOTE: If you are changing SCSI IDs on the host bus adapter to avoid conflicts, change the IDs before turning host power OFF. NEXT If you are changing IDs on one (or two) of this jukebox to avoid conflicts, the following steps include this option. 1.
Page 28 ETTING UP THE UKEBOX NOTE: If you are changing autochanger/drive IDs, refer to “Changing SCSI IDs” in Chapter 3. Return to this NOTE to continue. After changing the IDs, turn the jukebox (or jukeboxes) to STANDBY then back to ON to write the changes into the jukebox memory.
Page 29 ETTING UP THE UKEBOX OVING OR HIPPING THE UKEBOX To move the jukebox a short distance, such as to another office or to another floor in your building, refer to “Moving the Jukebox a Short Distance”. To ship the jukebox to another location, refer to “Shipping the Jukebox”.
Page 30 ETTING UP THE UKEBOX 6. Set up the jukebox at its new location, following the procedures in the beginning of this chapter. HIPPING THE UKEBOX 1. Unmount any optical disk surfaces in the jukebox if necessary. See your computer operating system, or software application documentation for instruction on how to unmount NEXT optical disks.
Page 31 ETTING UP THE UKEBOX The disk transport mechanism will lower to the chassis when power is turned off. The position at the bottom of the chassis is correct for insertion of the shipping screw (inserted in Step 6). 4. Remove the power cord from the wall/floor receptacle and the SCSI cable from the jukebox rear panel (see “1” and “3”...
Page 32 NOTE: A list of Hewlett-Packard optical media is in Appendix A, Table A-1. PRINT To see a list of HP-qualified media manufacturers, go to the “Product Information” section at www.hp.com/go/optical. HP reserves the right to change this list at any time.
Page 33 SING PTICAL ISKS HOOSING AN PTICAL Two disk types are available for use in the jukebox: rewritable disks and write-once disks. To choose which type of disks to use, consider these points: • Rewritable optical disks--data can be repeatedly written and erased. NEXT •...
Page 34 SING PTICAL ISKS ABELING AN PTICAL ARTRIDGE Make it a practice to label your optical disk cartridges. You are provided adhesive labels with each disk for this purpose. Here are some suggestions for labeling: NOTE: Your jukebox application software may label your optical disk slot locations differently. Use your application to check disk locations prior to labeling the disks.
Page 35: Figure 2-1: Recommended Placement Of Cartridge Labels
SING PTICAL ISKS Figure 2-1: Recommended Placement of Cartridge Labels NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 36 SING PTICAL ISKS RITE ROTECTING AN PTICAL Each side of an optical disk can be write-protected by sliding the write-protect button in the direction of the arrow on the cartridge (see Figure 2-2). With rewritable optical disks, write-protecting the disk prevents overwriting existing files and prevents any additional NEXT file being written to the disk.
Page 37: Figure 2-2: Write-Protect Button Location
SING PTICAL ISKS Figure 2-2: Write-Protect Button Location NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 38 SING PTICAL ISKS ARING FOR PTICAL ISKS Follow these guidelines to ensure that your optical disks remain in good condition: • Do not expose disks to extreme magnetic fields. • Do not expose disks to dust particles. NEXT • Do not expose disks to extreme temperatures or extreme humidity. •...
Page 39 SING PTICAL ISKS Caution: Be very careful when cleaning an optical disk. Abrasive particles dragged across the disk surface can damage the disk and prevent recovery of some or all of the data on the disk. Clean a disk only with an approved disk cleaning kit. Follow the disk cleaning kit instructions exactly. HP-approved disk cleaning kits are listed at www.hp.com/go/optical.
Page 40 PERATING THE UKEBOX 3Operating the Jukebox VERVIEW OF HAPTER This chapter describes how to do the following: • identify front panel features NEXT • use selection buttons • interpret displayed messages PREVIOUS • load optical disks into the jukebox • eject optical disks from the jukebox JUMP •...
Page 41: Figure 3-1: Features On The Front Panel
PERATING THE UKEBOX NDENTIFYING RONT ANEL EATURES Figure 3-1: Features on the Front Panel NEXT PREVIOUS JUMP CONTENTS INDEX Mailslot Used to load and eject disks. 9-Character display Displays information about the current operation.
Page 42 PERATING THE UKEBOX Selection buttons Pressed to perform the following operations: CANCEL cancels the current operation or choice scrolls the displayed choice backward by one PREV scrolls the displayed choice forward by one NEXT selects the displayed choice ENTER Drive indicator Lit when the optical drive mechanism is being accessed.
Page 43: Figure 3-1: Menu Tree - Top Level
PERATING THE UKEBOX SING ELECTION UTTONS Use the , and buttons to select tasks you want the jukebox to perform. When you push CANCEL PREV NEXT ENTER these buttons, the message in the display window changes. See the next section for a list of messages. Each time you push the NEXT PREV...
Page 44: Figure 3-2: Menu Tree - Top Level, With Configuration 15 On
PERATING THE UKEBOX Figure 3-2: Menu Tree - Top Level, With Configuration 15 ON NEXT Figure 3-3: Menu Tree - Top Level, With Configuration 32 ON PREVIOUS JUMP CONTENTS INDEX * Displays if the mailslot is open. ** Displays if the mailslot is closed.
Page 45 PERATING THE UKEBOX NDERSTANDING ISPLAY INDOW ESSAGES The jukebox displays messages according to your keypresses on the control panel. One level of messages is to tell you which operation you have selected, another level is to give you feedback to which options you are selecting under each operation.
Page 46 PERATING THE UKEBOX CONF * - select to customize the way the jukebox functions (CONFigurations) INFO * - select to retrieve performance information SCSI ID * - select to set the SCSI IDs for the jukebox controller and the optical drive mechanisms. NEXT NOTE: An “*”...
Page 47 PERATING THE UKEBOX SING THE RONT ANEL EATURES This section gives step-by-step instructions for tasks that are accessed by using the selection buttons on the control panel. Tasks included in this section are: NEXT • loading a disk into the jukebox ejecting a disk from the jukebox PREVIOUS setting a security code...
Page 48: Figure 3-4: Loading A Disk Cartridge
PERATING THE UKEBOX OADING A ARTRIDGE NTO THE UKEBOX Label all disks before inserting them into the jukebox. (See Labeling an Optical Disk Cartridgein Chapter 2 for instruc- tions.) Figure 3-4: Loading a Disk Cartridge NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 49: Figure 3-5: Menu Tree - Loading A Disk Cartridge
PERATING THE UKEBOX NOTE: Some software packages require that you insert and remove disks by following the instructions in the software. If you are using a software package to manage files in the jukebox, check the software documentation before proceeding with these steps.
Page 50: Figure 3-6: Menu Tree - Ejecting A Disk Cartridge
PERATING THE UKEBOX 2. If the displayed storage slot number is the one you want, press . If you want to choose a different storage ENTER slot, press until the desired slot number is displayed and then press NEXT ENTER NOTE: Any time during the load sequence you may press and the cartridge will be returned to the mailslot.
Page 51 PERATING THE UKEBOX 2. Press . SLOT ## displays. (“##'' is a slot number from 1-24 where a disk is stored. ENTER DRIVE # may also display, indicating there is a disk in a drive.) 3. If the number of the slot (or drive) that is displayed is the one you want, press ENTER If you want a different numbered slot (or drive), press until that number displays.
Page 52: Figure 3-7: Menu Tree - Setting A New Security Code
PERATING THE UKEBOX ETTING A ECURITY Figure 3-7: Menu Tree - Setting a New Security Code NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 53 PERATING THE UKEBOX The security code 0 0 0 is set at the factory. This code is used when accessing and setting jukebox configurations. Consider changing the security code so that only authorized persons can change the configurations. NOTE: Don’t forget your security code. If you forget it, only your service representative can reset the security code to the factory setting so you can set a new code.
Page 54 PERATING THE UKEBOX After entering the current security code in the previous steps, you are prompted to enter a new three-digit security code. 11. Press ENTER . NEW 1 and a flashing digit displays (the previous code 1). 12. Press NEXT until the first number you want in your security code displays 13.
Page 55 PERATING THE UKEBOX USTOMIZING THE PERATION OF THE UKEBOX You can customize the way the jukebox operates by setting values in its “configurations.”. See Table 3-1 for a list of these configurations, their default settings, and possible settings. NOTE: Your security code is required to change security configurations 15, 17, 20, 31, and 32. NEXT PREVIOUS JUMP...
Page 56: Figure 3-8: Menu Tree - Changing A Security Configuration
PERATING THE UKEBOX HANGING A ECURITY ONFIGURATION Figure 3-8: Menu Tree - Changing a Security Configuration NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 57 PERATING THE UKEBOX Configurations that affect security of your disks in the jukebox are numbered 15, 17, 20, 31, and 32. Table 3-1 describes these configurations. During the process of setting the security configurations, you are prompted for your current security code. If you have not changed the default security code, enter 0-0-0.
Page 58 PERATING THE UKEBOX 10. Press ENTER The current default setting displays. It may be any one of these settings • OFF or ON • a number NEXT 11. Select the option you want by pressing NEXT PREV 12. Press ENTER .
Page 59 PERATING THE UKEBOX Caution: The next step is to turn the jukebox to STANDBY. Do not turn power to STANDBY in this jukebox until you are sure the SCSI bus is inactive. Removing power from a SCSI peripheral when the bus is active can result in data loss and/or indeterminate bus states. Check your host system manuals for information about checking the SCSI bus status.
Page 60: Figure 3-9: Menu Tree - Setting A Non-Security Configuration
PERATING THE UKEBOX ETTING A ECURITY ONFIGURATION Figure 3-9: Menu Tree - Setting a Non-Security Configuration NEXT PREVIOUS JUMP CONTENTS INDEX Start with READY or SECURE in the display. 1. Press NEXT until CONF * displays.
Page 61 PERATING THE UKEBOX 2. Press . CONF 0 and a flashing 0 displays. ENTER 3. Press until the number of the option you want to change displays. NO CONFIG displays if you choose an NEXT invalid number. 4. Press ENTER The current default setting displays.
Page 62: Configurations
PERATING THE UKEBOX 8. Turn the jukebox to STANDBY, then ON to save the code to the jukebox memory. Table 3-1: Configurations Number Function Default Settings 0-14 Used by service personnel only. Changing these configurations may result in an inoperable jukebox.
Page 63 PERATING THE UKEBOX Table 3-1: Configurations Number Function Default Settings 28-30 Not used Enabling/disabling Off - Normal mailslot operation. mailslot access. On - The mailslot rotates to face inward when Configuration 15 is set to ON or a Prevent Media NEXT Removal command is received from the host computer.
Page 64 PERATING THE UKEBOX Table 3-1: Configurations Number Function Default Settings Forces the optical ON - Write verify is forced. drive to execute a OFF - The drive may write verify or not, depending on verify after every how they are manually configured or how they are write configured by the jukebox application software.
Page 65: Figure 3-10: Menu Tree - Retrieving Information
PERATING THE UKEBOX ETRIEVING NFORMATION OGGED BY THE UKEBOX Figure 3-10: Menu Tree - Retrieving Information NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 66: Information Logs
PERATING THE UKEBOX You can display information about the operations of the jukebox by using the INFO * option. This information is called a log. See Table 3-2 for a list of logs. Start with READY or SECURE in the display. 1.
Page 67 PERATING THE UKEBOX Table 3-2: Information Logs Description Total disk transport mechanism flips. Total mailslot rotations. Optical drive 1 SCSI ID. NEXT Optical drive 2 SCSI ID (if installed) Other logs are used by service. PREVIOUS JUMP CONTENTS INDEX...
Page 68: Figure 3-11: Menu Tree - Changing Scsi Ids
PERATING THE UKEBOX SCSI ID HANGING Figure 3-11: Menu Tree - Changing SCSI IDs NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 69 PERATING THE UKEBOX The jukebox controller uses two SCSI IDs if your jukebox has one drive and three IDs if your jukebox has two drives. The jukebox controller is assigned one ID and one ID is assigned to each disk drive. The default SCSI IDs are as follows •...
Page 70 PERATING THE UKEBOX NOTE: CONFLICT displays if you attempt to set the jukebox controller and a drive to the same ID. Repeat the procedure and reset one of the IDs to another, non-conflicting ID. NOTE: After you change an ID you may have to restart your host computer for the new ID to be recognized. Caution: Do not turn power to STANDBY in this jukebox until you are sure the SCSI bus is inactive.
Page 71 PERATING THE UKEBOX NOTE: CONFLICT displays if you attempt to set the jukebox controller and a drive to the same ID. Repeat the procedure and reset one of the IDs to another, non-conflicting ID. NOTE: After you change an ID you may have to restart your host computer for the new ID to be recognized. Caution: Do not turn power to STANDBY in this jukebox until you are sure the SCSI bus is inactive.
Page 72 PERATING THE UKEBOX UNNING AN NTERNAL The jukebox is capable of running internal tests. These tests are used for service diagnostic purposes. You may be asked to run some tests by the service representative prior to coming to your site. Results of the tests can provide service with important information that can help service to more quickly resolve the problem in your jukebox.
Page 73: Figure 3-12: Menu Tree - Running An Internal Test
PERATING THE UKEBOX Figure 3-12: Menu Tree - Running an Internal Test NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 74 PERATING THE UKEBOX * If the message is PASS (test number) and you press , the test number flashes and the jukebox is ready to accept ENTER another choice of test to run using the buttons. If you press when PASS is displayed, you will NEXT PREV CANCEL...
Page 75 PERATING THE UKEBOX ROUBLESHOOTING This section provides steps you can take when problems occur during operation. To troubleshoot problems, first refer to the procedures in this troubleshooting section. More Information is available at the HP’s Customer Care web site for optical jukeboxes at www.hp.com/support/optical. NEXT Customer Care may also be accessed by going to www.hp.com and select “HP Services and Support.”...
Page 76: Troubleshooting
PERATING THE UKEBOX Table 3-3: Troubleshooting Problem What to do Jukebox won’t power • Check that the drive activity indicator light on the control panel is ON (“4” on Figure 3-1) while you see TESTING in the display. NEXT • If light is not ON, make sure the standby/on switch on the rear panel is in the ON position and that the jukebox is plugged in.
Page 77 PERATING THE UKEBOX Table 3-3: Troubleshooting Problem What to do Power to the jukebox Power cycle the jukebox.* failed while a disk was If the poweron test is unsuccessful, place the standby/on switch in the drive and did not to STANDBY. Do not move the jukebox! Moving the jukebox return to READY after when there is a disk cartridge inside the drive risks damaging the NEXT...
Page 78 PERATING THE UKEBOX Table 3-3: Troubleshooting Problem What to do Changed a drive or • Ensure that no other device IDs conflict with the new ID. If jukebox ID but the host you find a conflict, change the ID and reboot the system (or does not recognize the rescan the bus).
Page 79 PERATING THE UKEBOX Table 3-3: Troubleshooting Problem What to do Disk inserted in the • Press and re-insert the disk in the mailslot. See CANCEL mailslot, LOAD ERR, “Loading an Optical Disk into the Jukebox” in this chapter or MISLOAD displays for the correct disk loading orientation.
Page 80 PERATING THE UKEBOX Table 3-3: Troubleshooting Problem What to do Disk eject attempted The host computer or application software has reserved the disk but RESERVED for its own use. You will not be able to eject this disk. displays If you want to change this configuration, refer to the host and/or application software documentation.
Page 81 PERATING THE UKEBOX Table 3-3: Troubleshooting Problem What to do Can’t write to the disk • Check the host computer or network file system access permissions. • Check that your disk is the correct density and is HP- qualified. NEXT •...
Page 82 UPPLIES AND USTOMER PORT ASupplies and Customer Support VERVIEW OF PPENDIX This appendix provides information on the following topics: • supplies and accessories NEXT • shipping screw specifications • HP customer support PREVIOUS JUMP CONTENTS INDEX PRINT...
Page 83 HP Direct. Call 1-800-752-0900 for the location of your nearest authorized Hewlett-Packard dealer. NEXT To contact a Hewlett-Packard sales representative, see Table A-2 for a list of addresses and phone numbers of HP sales offices. PREVIOUS To phone HP Direct call 1-800-227-8164 (USA), 1-800-387-3154 (Canada), or 4122-780-8111 (Europe)
Page 84: Basic Supplies And Accessories
UPPLIES AND USTOMER UPPORT Table A-1: Basic Supplies and Accessories Item HP Part Number 5.2- and 4.7-Gbyte Optical Disks Rewritable optical disk (2,048 bytes/sector, 5.2 88147J Gbytes, single disk) NEXT Write-once optical disk (2,048 bytes/sector, 5.2 88146J Gbytes, single disk) Rewritable optical disk (1,024 bytes/sector, 4.7 88143J Gbytes, single disk)
Page 85 UPPLIES AND USTOMER UPPORT Table A-1: Basic Supplies and Accessories Item HP Part Number 2.6- and 2.3-Gbyte Optical Disks Rewritable optical disk (1,024 bytes/sector, 2.6 92280F Gbytes, single disk) Write-once optical disk (1,024 bytes/sector, 2.6 92290F NEXT Gbytes, single disk) Rewritable optical disk (512 bytes/sector, 2.3 Gbytes, 92279F single disk)
Page 86 UPPLIES AND USTOMER UPPORT Table A-1: Basic Supplies and Accessories Item HP Part Number Disk Cleaners Check under “Product Catalog” at the web site ---------------- www.hp.com/go/optical Documentation NEXT User’s Guide (replacement/additional) C1118-90000 (printed English version) C1118-90020 (CD- PREVIOUS ROM with English and localized languages) JUMP...
Page 87 UPPLIES AND USTOMER UPPORT HIPPING CREW PECIFICATIONS If you have misplaced the shipping screw, you can use a cap screw with these specifications: 6/32 UNC-2B cap screw, 1-3/4 inches long. HP part number 2360-0551, orderable from HP Direct. See phone numbers and mail address of HP Direct on page NEXT...
Page 88 A quick way to do this is by using “Support Ticket” in the “Library Support Tools 2.0” (for Windows 95/98/ and NT 4.0). This suite of tools is available on the web at the locations described under “Hewlett-Packard Customer Support”...
Page 89 A quick way to do this is by using “Support Ticket” in the “Library Support Tools 2.0” (for Windows 95/98/ and NT 4.0). This suite of tools is available on the web. See “Hewlett-Packard Customer Support” on page 7. PREVIOUS...
Page 90 UPPLIES AND USTOMER UPPORT UROPE UROPEAN USTOMER ANAGEMENT ENTER Monday - Friday, 8:30am - 6pm Netherlands Time Table A-2: Austria 0660 6386 Netherlands 020 606 8751 Belgium Norway 22 11 6299 NEXT Dutch 02 626 8806 Poland 22 519 0600 French 02 626 8807 Portugal...
Page 91 UPPLIES AND USTOMER UPPORT - HP C ACIFIC USTOMER UPPORT ENTER Table A-3: Australia 8:30 - 17:30 Mon-Fri (03) 9272-8000 China 8:30 - 17:30 Mon-Fri (8610) 62625666 x5602, 5609, 5611, 5612 (8610) 62 61 4174 NEXT (8610) 62 61 4175 (8610) 62 61 4176 Japan 9:00 - 1200...
Page 92 A quick way to do this is by using “Support Ticket” in the “Library Support Tools 2.0” (for Windows 95/98/ and NT 4.0). This suite of tools is available on the web. See “Hewlett-Packard Customer Support” on page 7. - model number of your jukebox...
Page 93 UPPLIES AND USTOMER UPPORT warranty support. Please have a credit card, PO number, or billing address ready. LSEWHERE IN THE ORLD Contact your authorized HP dealer/distributor or the nearest HP sales and service office. DDITIONAL ELEPHONE UPPORT NEXT Table A-4: Singapore Customer Care-Line for End-Users (65) 272-5300 PREVIOUS...
Page 94 UPPLIES AND USTOMER UPPORT ARRANTY HP PRODUCT DURATION OF WARRANTY C1118J/C1119J One Year 1. HP warrants HP hardware, accessories and supplies against defects in materials and workmanship for the period NEXT specified above. If HP receives notice of such defects during the warranty period, HP will, at its option, either repair or replace products which prove to be defective.
Page 95 UPPLIES AND USTOMER UPPORT preparation or maintenance. 7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
Page 96 PERATING UKEBOX ON A SCSI B BOperating This Jukebox on a SCSI Bus SCSI RIEF VERVIEW OF ENERAL NEXT The Small Computer System Interface (SCSI), is a contention-based bus that accommodates different speed devices without impacting the devices with faster transfer speeds. This specification was defined by the American National Standards Institute (ANSI) in 1986.
Page 97 SCSI B PERATING UKEBOX ON A the bus, the ID also determines the priority of the device during contention among the devices for use of the bus. The narrow SCSI bus, with its eight data lines, can communicate with eight devices that have IDs from 0 to 7. The wide SCSI bus, with its 16 data lines, can communicate with 16 devices that have addresses from 0 to 15.
Page 98 SCSI B PERATING UKEBOX ON A [1] Priority - the order at which contentions on the bus are resolved [2] Narrow Addresses - IDs from 0 to 7 available on a narrow bus [3] Wide Address Range - IDs from 0 to 15 available on a wide bus The following diagram below shows the linear addressing of a simple, narrow bus with the host bus adapter set at a SCSI ID of 7.
Page 99 SCSI B PERATING UKEBOX ON A ERMINATION To keep signals on the SCSI bus from being reflected, “terminators” must be placed at each end of the physical bus. These terminators may be either active or passive. Passive termination is a resistor network. Active termination uses a voltage regulator (the active component) to regulate the power of the resistor network to provide more stable termina- tion.
Page 100 SCSI B PERATING UKEBOX ON A NEXT PREVIOUS JUMP CONTENTS [1] Terminator - device required on each end of a SCSI bus to prevent reflected signals [2] SCSI Device - a device on the internal SCSI bus INDEX [3] Host Bus Adapter - SCSI bus connecting point [4] Host Internal - SCSI components internal to the host computer [5] External - SCSI components external to the host computer [6] SCSI Device - SCSI device external to the host computer...
Page 101 SCSI B PERATING UKEBOX ON A INGLE ENDED OLTAGE IFFERENTIAL OLTAGE IFFERENTIAL NTERFACES The SCSI bus is electrically implemented in three ways: single-ended, high-voltage differential, and low-voltage differ- ential. These terms come from the way the signals are asserted on the bus. NEXT Single-ended buses use a 5-volt signal that is referenced to ground.
Page 102 SCSI B PERATING UKEBOX ON A Micro D connector, described below. • 50-pin high density Micro D (using thumbscrews or small clips) (external) • This connector is similar to a D-type connector, but smaller and with smaller pin holes placed closer together. •...
Page 103 SCSI B PERATING UKEBOX ON A NOTE: For more complete information on the theory and operation of the SCSI bus, you may want to go to: Adaptec - major supplier in SCSI buses www.adaptec.com Symbios Logic - Working drafts of SCSI specifications www.symbios.com/x3t10 NEXT PREVIOUS...
Page 104 SCSI B PERATING UKEBOX ON A SCSI B US AND UKEBOX This jukebox is a “fast and narrow” SCSI device that uses either a single-ended or low-voltage differential external SCSI bus. The external connectors on the jukebox are “wide” (68-pin) but, because the internal SCSI bus in the jukebox is “narrow,”...
Page 105 SCSI B PERATING UKEBOX ON A IXING IDE AND ARROW EVICES As a preliminary note to this discussion, HP highly recommends that you do NOT mix wide and narrow buses. Connecting devices of the same bus width, such as all narrow (50-pin) is a simple process of daisy-chaining the devices, and terminating both ends of the bus.
Page 106 SCSI B PERATING UKEBOX ON A NEXT PREVIOUS JUMP [1]Bus Adapter - connecting point for all SCSI devices CONTENTS [2] Wide SCSI Device - accepts IDs from 0 to 15 [3] 68-50-Pin SCSI Cable - adapts from wide to narrow connectors INDEX [4] Narrow SCSI Device - accepts IDs from 0 to 7 [5] Terminator - device on the ends of a SCSI bus to prevent reflected signals on the bus...
Page 107 “legal” SCSI configuration, it is not a configuration that is recommended by Hewlett-Packard. As a general rule, HP recommends that the jukebox be the only device on a bus. If there are multiple...
Page 108 SCSI B PERATING UKEBOX ON A [1]Bus Adapter - connecting point for all SCSI devices [2] Wide SCSI Device - accepts IDs from 0 to 15 [3] Wide SCSI Cable - 68-pin SCSI Cable [4] 68-50-Pin SCSI Cable - adapts from wide to narrow connectors - high 18 lines must be terminated NEXT [5] Narrow SCSI Device - accepts IDs from 0 to 7 [5] Terminator - device on the ends of a SCSI bus to prevent reflected signals on the bus (50-pin)
Page 109 SCSI B PERATING UKEBOX ON A metres allowable minus 0.41 metres for internal cabling.) ERMINATION • Refer to the documentation that comes with your particular adapter to see how to apply termination. • Use active terminators on single-ended buses to reduce noise sensitivity. Use low-voltage differential terminators if NEXT using a low-voltage differential bus.
Page 110 SCSI B PERATING UKEBOX ON A NEXT PREVIOUS JUMP CONTENTS [1] Terminator - device on each end of a SCSI bus to prevent reflected signals [2] SCSI Device - a device on the internal SCSI bus INDEX [3] Host Bus Adapter - SCSI bus connecting point [4] Host Internal - SCSI components internal to the host computer [5] External - SCSI components external to the host computer [6] SCSI Device - SCSI device external to the host computer...
Page 111 SCSI B PERATING UKEBOX ON A ENERAL • Do not connect a single-ended or low-voltage differential bus with high-voltage differential devices. Damage can occur. NOTE: For current information on issues relating to installation, operation, and support of jukeboxes, go to www.hp.com/support/ optical.
Page 112 AFETY AND EGULATORY NFORMATION CSafety and Regulatory Information VERVIEW OF THIS PPENDIX This appendix contains important safety and regulatory information for the United States, Finland, Sweden, Germany, United Kingdom, European Union, and Japan. NEXT PREVIOUS JUMP CONTENTS INDEX PRINT...
Page 113 AFETY AND EGULATORY NFORMATION CDRH R (USA O EGULATIONS The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented reg- ulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976.
Page 114 AFETY AND EGULATORY NFORMATION 1984 NITED INGDOM ELECOMMUNICATIONS The Hewlett-Packard 125ex optical jukebox is approved under Approval Number NS/G/1234/J/100003 for indirect connection to Public Telecommunication Systems within the United Kingdom. NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 115 AFETY AND EGULATORY NFORMATION EC D ECLARATION OF ONFORMITY NEXT PREVIOUS JUMP CONTENTS INDEX...
Page 116 AFETY AND EGULATORY NFORMATION ERSTELLERBESCHEINIGUNG Diese Information steht im Zusammenhang mit den Anforderungen der Maschinenlärn information sverordnung vom 18 Januar 1991. Schalldruckpegel Lp < 70 dB(A) NEXT • am arbeitsplatz • normaler betrieb PREVIOUS • nach ISO 7779:1988/EN 27779:1991 (Typprüfung) NGLISH RANSLATION OF ERMAN...
Page 117 Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för laserstrålning, som INDEX överskrider gränsen för laserklass 1. UOLTO Hewlett-Packard 125ex levymuistiasemien sisällä ei ole käyttäjän huollettavissa olevia kohteita. Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Levymuistiaseman sisälle asennettujen luku-/kirjoitusyk- siköiden suojakoteloa ei tule avata huoltotoimenpiteiden yhteydessä.
Page 118 AFETY AND EGULATORY NFORMATION VARO ! Mikäli luku-/kirjoitusyksikön suojakotelo avataan ja suojalukitus ohitetaan, olet alttiina lasersäteilylle laitteen ollessa toiminnassa. Älä katso säteeseen. VARNING ! Om skyddshöljet av den optiska drivmodulen öppnas och spärren urkopplas då apparaten är i funktion, utsättas använ- NEXT daren för laserstrålning.
Page 119 NEXT CLASS 1 LASER PRODUCT (The same in Swedish.) Hewlett-Packard 125ex optical jukebox is for user safe class 1 laser products. In normal use the enclosure of the optical PREVIOUS drives prevents the laser beam from escaping outside of the product.
Page 120 AFETY AND EGULATORY NFORMATION WARNING ! If the enclosure of the optical drive mechanism is opened and the safety interlock disabled, you may be exposed to the laser radiation when the drive is operating. Avoid exposure to the beam. (The same warning in Swedish.) The information about the radiation characteristics of the laser diode used in the optical drive mechanism: NEXT Wavelength...
Page 121 AFETY AND EGULATORY NFORMATION VCCI S APANESE TATEMENT NEXT PREVIOUS APANESE ARMONICS TATEMENT JUMP CONTENTS INDEX...
Page 122 Glossary cartridge A plastic enclosure that contains an optical disk. The cartridge is labeled “A” or “B” to denote separate sides NEXT of the optical disk. The optical disk is never removed from the cartridge. disk See optical disk. PREVIOUS driver A program that allows the operating system to communicate with a peripheral device.
Page 123 jukebox A term synonymous with optical disk library or autochanger. This type of optical storage device is often referred to as a “jukebox” because when a file is requested, the disk containing the file is found, inserted into the drive, and the requested information is sent to the host computer system, similar to the way a musical jukebox finds a record and moves it to the turntable when a song is requested.
Page 124 able or write-once mode. optical disk A term synonymous with the 5.25-inch magneto-optical disk. There are two types of optical disks used in jukeboxes: rewritable and write-once. optical disk library See jukebox. NEXT PREVIOUS rear panel The rear panel of the jukebox provides two SCSI bus connectors that can be used for either single-ended or low-voltage differential bus connections.
Page 125 write protect A feature that prevents data from being written to a disk. A write protect tab is located on both sides of the optical disk cartridge to enable write-protection on one or both surfaces of the disk. write-once An additional operating mode available with multifunction drives. When a write-once disk is inserted, the NEXT drive will write data, but will not write over data that has been previously written.
Page 126 NDEX &KDSWHU7LWOH,QGH[ Numerics...

HP Surestore 125ex - Optical Jukebox Manual

Quick Links

Related Manuals for HP Surestore 125ex - Optical Jukebox

Summary of Contents for HP Surestore 125ex - Optical Jukebox

Table of Contents