Table of Contents
Advertisement
MICRO WAVE OPERATING
INSTRUCTIONS
CHANGING OVEN SIGNAL
Your oven features an entry signal and an end-of-cycle signal that
are programmed to be on, but can be deactivated, if you choose.
The entry signal is set to "beep" whenever a pad is pressed, It
confirms the oven has "read" and accepted your instructions, The
end-of-cycle signal is set to "beep" at the end of the cooking time or
when food has reached a set temperature.
Follow these instructions, to cancel the entry signal or end-of-cycle
signal:
1. Press and hold
MEMORY SET
for 5 seconds
or until "OP:10" or "OP:I 1" is displayed. (See chart for
definition of signal options.)
2. To change the signal option, press 0 if you wish to deac-
tivate the entry signal. Press
I
if you wish to activate the
entry signal.
3. Press
MEMORY SET.
"OP:20" or "OP:21" will be
displayed. You are now ready to change the signal optionfor
the end-of-cycle signal, if desired.
,,,_s_
_=-,,-_,.-_
4. To exit the signal option mode, press ;_ I UI"/MIZ.;_P-/
once.
SIGNAL OPTIONS
Option
Number
Option Function
OP:10
Prevents a beep signal from sounding when a
pad is pressed.
OP:I 1"
Allows a beep signal to sound when a pad is
pressed,
OP:20
Prevents the end-of-cycle signal from sounding
when heating time is over. **
OP:21"
Allows a signal to sound at the end of the
heating time and timer cycle.
*As shippedfrom factory
**It also preventsthe endof timer signalfrom sounding.
CHECKING 0 YEN OPERATION
A. Oven Light
,3.
Press
CLOCK
again. The clock is now set. If oven
The oven light will come on when the door is opened. It will also!
power is interrupted (for example, if the supply circuit is dis-
come on when the oven is operating,
connected, or if there is a power failure), all programming
B. Set the Clock
instructions will be erased. When power is reconnected
dashes will appear in the display. You must then reset the
1. Press
CLOCK.
"CLOCK" will be displayed.
_/
clock as indicated above.
2. Enter the time of day. For example, if it is 10:35 (a.m. qrj ..m.)
press
1,0,3,5,
in that order.
,_/
C. Check operation of the interlock systems. The
START
and
STOP/RESET
turn the oven on and off. Microwave
energy is generated only when the door is closed, cooking time,
weight or temperature has been set and
START
has been
pressed. In addition,the oven has interlockswitches to assure no
microwave energy isgenerated when the door is open. To check
or remove food before the cookingtime has elapsed, you may
either press
STOP/RESET
or open the oven door to
turnthe oven off. Before the oven door opens, hidden interlock
switches sense the motion of the door handle and automatically
turnthe oven off.
Here is how you may check the operation of
START,
STOP/RESET
and the interlock switches:
1. Place a glass of water in oven and close oven door.
2. PressTIME ENTRY.
3. Press 5, then 0.
4. Press
START.
The oven should operate and the oven
lightshould come on.
5. Press STOP,
The oven should shut off immediately and
the sound of the motor shouldcease. The oven light should
go out.
6. Open oven door fully. The oven light shouldcome on when
the door is opened.
7. Press STOP/RESET.
If under any of the preceding conditions the oven does not operate
as stated, do not use it. Call your Amana dealer or authorized
service agency.
18
Advertisement
Table of Contents
