Brother KE-484C Instruction Manual page 57

13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
<Memory switches 30 - 4F>
30 to 4F are set by entering two-digit values.
These values are incremented using the P2 switch, and decremented using the P4 switch.
Switch Possible setting range
memo-30 0 - 99
memo-31 0 - 60
memo-32 12 - 25
memo-33 1 - 10
memo-34 0 - 5
memo-35 3 - 9
−
memo-36
memo-37 1 - 20
memo-38 1 - 20
memo-39 1 - 20
memo-3A 1 - 20
memo-3b 1 - 20
memo-3c 0 - 99
−
memo-3d
−
memo-3E
−
memo-3F
memo-40 1 - 5
−
memo-41
memo-42 0 - 13
memo-43 1 - 3
memo-44 0 - 3
memo-45
−
-
memo-4c
memo-4d 0 - 10
memo-4E 2 - 9
memo-4F 14 - 19
51
Units Initial value
Limits the maximum area in the horizontal direction (X).
mm 99 (If the value is set to 99, the maximum length allowed will be 100
mm)
mm 60 Limits the maximum area in the vertical direction (Y).
× 100rpm
25
Changes the maximum sewing speed.
Changes the feed timing.
× 7.5°
5
1 (Fast) ← 5 (Standard) → 10 (Slow)
The (setting value + 1) number of stitches are sewn at the speed
Stitch 0 set by memo-35 at the sewing start. (No low-speed sewing if set
to 0.)
Changes the sewing start speed for the number of stitches
× 100rpm
4
specified by memo-34.
− −
−
Changes the feed timing one stitch before the sewing end.
× 7.5°
10
1 (Fast) ← 10 (Standard) → 20 (Slow)
× 7.5°
10 Changes the feed timing two stitches before the sewing end.
× 7.5°
10 Changes the feed timing for the third stitch at the sewing start.
× 7.5°
10 Changes the feed timing for the second stitch at the sewing start.
× 7.5°
10 Changes the feed timing for the first stitch at the sewing start.
Sets the number of stitches for which the feed timing (memo-33
setting) is enabled.
Stitch 0 0: Enabled for all stitches
1 - 99: Enabled for the specified number of stitches from the
sewing start
− − −
− −
−
− − −
Changes the test feeding speed (with no material).
−
4
1 (Fast) ←→ 5 (Slow)
− −
−
The work clamp operating mode can be changed. (When set to
"0", the mode is selected according to the settings for DIP
−
0
switches A-1 and A-2.)
Refer to "14. SETTING THE WORK CLAMP MODE" for details of
the available modes.
Changes the allowable speed/sewing pitch.
−
3
1 (Fast) ←→ 3 (Standard)
Changes the path taken when moving from the machine home
position to the start position.
−
0
0: Across inside of work clamp, 1: Top-left, 2: Bottom-left,
3: Bottom-right
− − −
× 100 ms
0 Changes the work clamp lift timing after sewing is finished.
Tension release ON timing after thread trimming.
× 7.5°
5
2 (Fast) ← 5 (Standard) →9 (Slow)
Thread trimming timing
× 7.5°
14
14 (Standard) ↔ 19 (Slow)
KE-484C
Explanation