Enterasys 2S4082-25-SYS Hardware Installation Manual page 14

5-1 LANVIEW LEDs for the 2S4082-25 .................................................................................................... 5-2
5-1 LANVIEW LEDs for the 7S4280-19 .................................................................................................... 5-2
5-2 OFFLINE/RESET Switch for the 2S4082-25 ...................................................................................... 5-6
5-2 OFFLINE/RESET Switch for the 7S4280-19 ...................................................................................... 5-6
6-3 Layer 2 In-Band Management Topology ............................................................................................ 6-4
6-4 Layer 2 Out-Of-Band Management Topology .................................................................................... 6-5
6-5 Layer 3 In-Band Management Topology ............................................................................................ 6-5
6-6 Layer 3 Out-Of-Band Management .................................................................................................... 6-6
6-7 Choose NAC Controller Installation Type ........................................................................................... 6-7
6-8 Enter the Management VLAN ID ........................................................................................................ 6-8
6-9 Enter Directly Connected Router IP Address ..................................................................................... 6-8
6-10 Setup NAC Controller Engine Networking for In-Band Installation Types .......................................... 6-9
6-11 Setup NAC Controller Engine Networking for Out-Of-Band Installation Types ................................ 6-10
6-12 Setup NAC Controller PEP Networking ............................................................................................ 6-10
6-13 Enter NetSight Server IP Address .................................................................................................... 6-11
6-14 In-Band Management Type Configuration Setup Confirmation ........................................................ 6-11
6-15 Out-Of-Band Management Type Configuration Setup Confirmation ................................................ 6-12
6-16 Configure System Date and Time .................................................................................................... 6-12
6-17 Set the System Date......................................................................................................................... 6-13
6-18 Set the System Time ........................................................................................................................ 6-13
6-19 Select the UTC/Local Hardware Clock Setting ................................................................................. 6-14
6-20 Timezone Configuraiton ................................................................................................................... 6-14
6-21 Enable an SNMP Daemon ............................................................................................................... 6-15
6-22 Enter SNMP System Information...................................................................................................... 6-15
6-23 NAC Controller PEP COM Port Location.......................................................................................... 6-16
6-24 Determining NAC Controller Mode of Operation .............................................................................. 6-17
6-25 Import From Device Wizard .............................................................................................................. 6-18
6-26 Import From Device Wizard .............................................................................................................. 6-19
6-27 Roles Screen .................................................................................................................................... 6-19
6-28 Services Screen ............................................................................................................................... 6-20
6-29 End-System to Assessment Server Classification Rule ................................................................... 6-20
B-1 Mode Switch Location on the NAC Controller PEP (2S4082-25 shown)............................................B-2
B-2 DIMM and DRAM SIMM Locations for the NAC Controller PEP (2S4082-25 shown)........................B-3
B-3 Removing the Existing DIMM .............................................................................................................B-3
B-4 Installing the DIMM.............................................................................................................................B-4
B-5 Removing Existing DRAM SIMM ........................................................................................................B-5
B-6 Installing the DRAM SIMM .................................................................................................................B-6
Tables
2-1 Power Supply (PS) LED Status Definitions ........................................................................................ 2-2
2-2 Fan LED States and Definitions ......................................................................................................... 2-3
3-1 Contents of the 2S4082-25-SYS and 7S4280-19-SYS 7C111 Carton ............................................... 3-2
4-1 Contents of Module Carton................................................................................................................. 4-2
5-1 LANVIEW LEDs.................................................................................................................................. 5-3
5-2 Troubleshooting Checklist .................................................................................................................. 5-4
A-1 Chassis Specifications........................................................................................................................A-1
A-2 7C111 Power Supply Specifications...................................................................................................A-2
A-3 Environmental Specifications .............................................................................................................A-2
A-4 Regulatory Compliance Standards .....................................................................................................A-2
A-5 NAC Controller Engine Specifications ................................................................................................A-3
A-6 COM Port Pin Assignments ................................................................................................................A-4
A-7 Specifications for 2S4082-25..............................................................................................................A-5
A-8 COM Port Pin Assignments ................................................................................................................A-6
A-9 Specifications .....................................................................................................................................A-6
xii