Set Up Speakers - Marantz AV7005 User Manual

ENGLISH DEUTSCH

Set up speakers

This section provides the setup methods of speaker systems other than the 7.1-channel system
(with surround back speakers).
For the setup methods of the 7.1-channel system with surround back speakers, see "Simple
version", "Set up speakers (Audyssey ® Auto Setup)" (vpage 8) of "Simple version".
First install and connect the speakers to this unit.
Before Auto Setup measurement, the settings shown below can be made.
• Changing the amplifier assignment (Amp Assign)
The signal output from the UNBALANCED and BALANCED PRE OUT SBL/SBR terminals of this unit can
be switched to match your speaker environment. (vpage 52 "Set up "Amp Assign"").
• Setting the channels to be used (Channel Select)
If channels that are not to be used are set in advance, measurement for the set channels is skipped, and
measuring time can be reduced (vpage 52 "Set up "Channel Select"").
n Audio output from each PRE OUT terminal
UNBALANCED PRE
FL/FR C SW1/SW2
OUT terminal
BALANCED PRE
FL/FR C SW1/SW2
OUT terminal
Subwoofer 1 /
Audio Output Front A Center
Subwoofer 2
*The output audio differs depending on the "Amp Assign" settings.
1
Set up the
remote control unit
n Set up the operation mode
Press AMP to set the remote control unit
to amplifier operation mode.
Press AMP
52
Remote control operation
buttons
FRANÇAIS ITALIANO ESPAÑOL
PRE OUT Channel
SL/SR SBL/SBR HL/HR
SL/SR SBL/SBR ---
Surround Front Height /
Surround
Back* Front B
2
Connect the setup microphone.
When the setup microphone is
connected, the following screen is
displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ XT
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter RETURN
Start Auto Setup
Move the cursor
(Up/Down/Left/Right)
NEDERLANDS SVENSKA
3
Set up "Amp Assign"
Use ui to select "Amp Assign",
and then press ENTER
AUTO SETUP
AUDYSSEY AUTO SETUP
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter
Set use of surround back ch. for your system
4
Use o p to select the configuration
WL/WR
of the connected speakers, and then
--- RETURN
press .
Normal Set when
Front Wide
back, front height or front wide
speakers. In this case, go to step
5.
ZONE2
Set for connecting the speakers
for ZONE2.
ZONE3
Set for connecting the speakers
for ZONE3.
SPKR-C Set for connecting the tweeter
of the front speaker to the
UNBALANCED and BALANCED
PRE OUT SBL/SBR terminals of
the power amp, and the woofer
of the front speaker to the FL/FR
terminals.
[1/6]
Cancel
Confirm the setting
around items indicate the settings.
5
Set up "Channel Select"
Use ui to select "Channel Select",
. and then press
AUTO SETUP
MultEQ XT AUDYSSEY AUTO SETUP
[1/6] STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
RETURN Cancel
Skip unused ch's measurement for timesaving
6
Use ui to select a channel.
Subwoofer Select for no subwoofers to be
used. In this case, go to step 7.
using surround
Surround
Select
Back
speakers to be used. In this case,
go to step 8.
• "Surround Back" can be set when
"Amp Assign" is set to "Normal".
Front
Select for no front height speakers
Height
to be used. In this case, go to step
9.
• "Front Height" can be set when
"Amp Assign" is set to "Normal".
Select for no front wide speakers to
Front Wide
be used. In this case, go to step 9.
• "Front Wide" can be set when
"Amp Assign" is set to "Normal".
7
GWhen "Subwoofer" is selected in
step 6H
Use to select the item.
o p
Measure Set for measuring a subwoofer.
Skip Set for no measuring of a subwoofer.
Return to previous menu
ENTER .
MultEQ XT
[1/6]
ENTER Enter RETURN Cancel
for no surround back