Marantz AV7005 User Manual page 13

2
Set up the subwoofer
If using a subwoofer capable of the
following adjustments, set up the
subwoofer as shown below.
n When using a subwoofer with a direct
mode
Set the direct mode to "On" and disable the
volume adjustment and crossover frequency
setting.
n When using a subwoofer without a
direct mode
Make the following settings:
• Volume : "12 o'clock position"
• Crossover frequency : "Maximum/Highest
Frequency"
• Low pass fi lter : "Off"
• Standby mode : "Off"
NOTE
When you use two subwoofers, please adjust
the subwoofer volume controls individually so
that each subwoofer level is as close as possible
to 75 dB using the test tone (vpage 79) before
Audyssey Auto Setup.
3
Set up the remote control
unit
n Set up the operation mode
AMP
Press to set the remote control unit
to amplifi er operation mode.
Press AMP
Remote control operation
buttons
SVENSKA NEDERLANDS
STEP 1
Preparation
4
Connect the setup microphone to the
SETUP MIC jack of this unit.
When the setup microphone is
connected, the following screen is
displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ XT
STEP1 Preparation [1/6]
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter RETURN Cancel
Start Auto Setup
This screen provides the method for setting
up 7.1-channel playback using surround back
speakers. For the method of setting up speakers
other than the 7.1-channel system, select "Amp
Assign" and perform step 3 and 4 of "Set up
"Amp Assign"" (vpage 52).
If unused channels are set with "Channel
Select", measuring time can be shortened. For
setting, perform steps 5 to 9 of "Set up "Channel
Select"" (vpage 52).
5
Use ui to select "Auto Setup Start"
and then press ENTER .
Move the cursor
(Up/Down/Left/Right)
ESPAÑOL ITALIANO
STEP 2
Speaker Detection
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
confi guration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
Select "Measure" and then press
ENTER
.
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
7
The detected speakers are displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ XT
[2/6]
STEP2 Spkr Detect Check
Front Yes
Center Yes
Subwoofer Yes
Surround Yes
S.Back 2spkrs
F.Height No
F.Wide No
Retry
Next Measurement
ENTER Enter RETURN Cancel
Go to Step 3 (Measurement) after speaker check
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
Use to select "Next
ui
ENTER
Measurement" and then press
Confi rm the setting
FRANÇAIS DEUTSCH
Set up speakers (Audyssey ® Auto Setup)
NOTE
If "Caution" is displayed:
Go to "Error messages" (vpage 11), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
"Audyssey Auto Setup".
When performing Audyssey Auto
Setup over again
ui
Press to select "Retry", and then press
When measuring has stopped
RETURN
Press , to the "Cancel Auto Setup?"
prompt is displayed.
Press o to select "Yes", then press
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation .
1
.
Return to previous menu
ENGLISH
ENTER
.
ENTER
.
9