Marantz AV7005 User Manual page 14

ENGLISH DEUTSCH
Set up speakers (Audyssey ® Auto Setup)
STEP 3
Measurement
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
Move the setup microphone to
position 2, use to select
ui
"Measure", and then press ENTER
The measurement of the second position
starts. Measurements can be made in up to
eight positions.
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ XT
STEP3 Measurement [3/6]
Please place the mic-
rophone at ear height
at 2nd listening
position.
Measure
Next Calculation
ENTER Enter RETURN Cancel
Start next measurement. Test Tone will start
If you want to omit measurements from the next
position onward, select "Next 1 Calculation".
(Go to STEP4 Calculation
)
10
Repeat step 9, measuring positions 3
to 8.
When measurement of position
completed, a "Measurements fi nished."
message is displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ XT
STEP3 Measurement [3/6]
Measurements finished.
Retry
Next Calculation
ENTER Enter RETURN Cancel
Proceed to Step 4 (Analyze)
10
Remote control operation
buttons
FRANÇAIS ITALIANO
STEP 4
Calculation
11
On the screen, use
STEP3
to select "Next 1 Calculation", and
then press ENTER .
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ XT
.
STEP4 Calculation
Now calculating...
Please wait.
25%
• Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
8 is
Move the cursor
(Up/Down/Left/Right)
ESPAÑOL NEDERLANDS SVENSKA
STEP 5
Check
12
Use to select the item you want
ui
ui
to check, and then press
AUTO SETUP
AUDYSSEY AUTO SETUP
STEP5 Check
Check processing res-
ults. To proceed,press
"Next"
Spkr Config Check
Distance Check
Ch. Level Check
Crossover Check
[4/6]
Next Store
ENTER Enter
Select item to check
• Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
• If you want to check another item, press
RETURN
.
13
Use to select "Next 1 Store"
ui
ENTER
and then press
NOTE
• If the result differs from the actual connection
status, or if "Caution!" is displayed, see "Error
messages" (vpage 11). Then carry out Audyssey
Auto Setup again.
• If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
• If you change speaker positions or orientation,
perform Audyssey Auto Setup again to fi nd the
optimal equalizer settings.
Confi rm the setting
STEP 6
Store
14
Select "Store" and then press
ENTER
. Save the measurement results.
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ XT
STEP6 Store
[5/6]
Press "Store" to store
calculation results.
Store
RETURN Cancel
Apply and store measurement result
AUTO SETUP
AUDYSSEY AUTO SETUP
STEP6 Store
Now storing...
Please wait.
.
25%
• Saving the results requires about 10 seconds.
• If the measuring results are not to be saved,
RETURN
press . A message "Cancel Auto
Setup?" will be displayed. Press o then select
"Yes". All the measured Audyssey Auto Setup
data will be erased.
NOTE
During saving of measurement results, be sure
not to turn off the power.
Return to previous menu
ENTER
.
MultEQ XT
[6/6]
ENTER Enter RETURN Cancel
MultEQ XT
[6/6]