Setup Of The Auto Ee Mode; Setup Of The Foot Switch Function - Fostex D2424LV Reference Manual

Model D2424LV Reference Manual (Changing the Initial Setting <SETUP mode>)
Setup of the Auto EE mode ("Auto EE Mode?" menu)
At the "Setup of the Auto EE mode" menu, you must set up whether it should be automatically set to "ALL INPUT
monitor" or not when D2424LV is in the STOP mode.
Setting the Auto EE mode
• Initial setting:
• Device ID:
* This setting is shared by all Programs in the same
disk.
* The settings cannot be saved and loaded as part of
the song data.
* The settings are maintained after you turn off the
power to the recorder.
1.While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
2.Turn the Jog dial to select "Auto EE Mode ?"
("?" flashes), then press the [EXECUTE/YES] key.
A flashing "?" will extinguish by pressing the [EXECUTE/
YES] key and the auto EE mode information that was lit
will being flashing. Initial setting, it will show "Off".
SETUP
OL
0
3
6
9
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11
SETUP
OL
0
3
6
9
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12
Setup of the Foot switch function ("Foot SW?" menu)
At the "Setup of the foot switch function" menu, functions of a foot switch connected to the FOOT SW jack must
be set up.
Functions of the foot switch are, manual punch in/out or PLAY-STOP of D2424LV. Initially, this is set to the
"Punch in/out function" explained in "Using the foot switch for manual punch in/out," page "43". You can change this
to PLAY-STOP of the recorder if you so wish.
Setting the foot switch function
• Initial setting:
• Options:
* This setting is shared by all Programs in the same
disk.
* The settings cannot be saved and loaded as part of
the song data.
* The settings are maintained after you turn off the
power to the recorder.
[Off]
[Off] or [On]
OL
BIT
0
3
6
9
12
18
24
30
42
12 13 14 15 16 17 18 19 20 21 22 23 24
Flashing
OL
BIT
0
3
6
9
12
18
24
30
42
13 14 15 16 17 18 19 20 21 22 23 24
[Punch IO]
[Punch IO] (Punch in/out
function) or [PLY/STP] (Play/
stop function)
3. With the Jog dial, select the auto EE mode.
4. After selecting "On" or "Off," press the [EXECUTE/
YES] key again.
The selected On/Off will be registered and the Step-2
"?" will return to flashing.
5.Press the [EXIT/NO] key or the [STOP] button
repeatedly to exit SETUP mode.
To cancel the operation, or to restore the setting
obtained prior to the [EXECUTE/YES] key press, press
the [STOP] button or the [EXIT/NO] key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
24
FS
kHz
CLOCK
INT
24
FS
kHz
CLOCK
INT
1.While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
2.Turn the Jog dial to select "Foot SW ?" ("?"
flashes), then press the [EXECUTE/YES] key.
A flashing "?" will extinguish by pressing the [EXECUTE/
YES] key and the foot switch function information that
was lit will being flashing. Initial setting, it will show
"Punch IO".
124