Setup Of The Chain Play List - Fostex D2424LV Reference Manual
24 track digital recorder
Hide thumbs
Also See for D2424LV:
- Quick operation manual (28 pages) ,
- Brochure (5 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
The chain play list is setup via the "Chain Play List?" menu in the SETUP mode.
The following procedure is based on the assumption that a multiple number of programs are in the current
drive and that a tune is recorded in each program.
1. Enter the SETUP mode by pressing the [SETUP] key
while the D2424LV is in the stop mode.
2. Use the Jog dial to display the "Chain Play List?,"
and then press the [EXECUTE/YES] key.
The display will change to setup of the play list.
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
This display indicates the initial setting in which no
chain list is setup ("EE" means "invalid.").
The chain play number can be set in the currently
blinking section (left) and numbers "01" through "99"
can be input via the Jog dial.
Also, the flashing section can be moved from the left
"01" to the right "EE" by pressing the [EXECUTE/YES]
key, and except for "EE," each program number
currently in the disk can be selected via the Jog dial.
3. Input the chain number via the Jog dial and press
the [EXECUTE/YES] key.
The flashing section will move from left to the right
"EE."
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
6
7
8
9
10
11
12
4. Select the desired program number via the Jog dial
and press the [EXECUTE/YES] key.
The chain number of the selected program will be set
and, the same as in <Step 2>, the left section will flash.
For example, if it has been set as shown below, the
setting will be for playback of the program 5 tune in
the second order.
SETUP
OL
0
3
6
9
12
18
24
30
42
1
4
5
6
7
8
9
2
3
10
11
12
Repeat these procedures to set up the chain play
number in the desired program.
Model D2424LV Reference Manual (Chain Play function)
Setup of the Chain Play List
OL
BIT
0
3
6
9
12
18
CLOCK
24
30
42
13
14
15
16
17
18
19
20
21
22
23
24
Flashing
OL
BIT
0
3
6
9
12
CLOCK
18
24
30
42
13
14
15
16
17
18
19
20
21
22
23
24
Flashing
OL
BIT
0
3
6
9
12
18
CLOCK
24
30
42
13
14
15
16
17
18
19
20
21
22
23
24
PGM
OL
BIT
0
3
6
9
12
18
CLOCK
24
30
42
13
14
15
16
17
18
19
20
21
22
23
24
<Setup example of the chain play list>
As an example, if the chain play list is set as
shown below, chain play is possible in the
order of: program 3 - program 5 - program 2.
If the chain list is to be ended after program
1, as shown in the example below, set "EE" at
fourth ("c04") in the chain list.
24
By selecting "EE," the chain play list setting
FS
kHz
will be "c01" - "c03," and beyond "c04" will be
INT
invalid.
"EE" can be selected with the Jog dial while
the right program number is flashing.
SETUP
24
FS
OL
0
kHz
3
6
9
INT
12
18
24
30
42
1
2
3
4
5
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
5
24
FS
kHz
INT
SETUP
OL
0
3
6
9
12
18
24
30
42
1
2
3
4
<Note>
• In order to execute chain play, " AUTO RTN
START point " and " AUTO RTN END point " must be
setup in each program to be played back.
Refer to previous page "50" for how to register
memory points.
24
• If the chain play list is edited even once, the
FS
kHz
Chain Play Mode will be set " OFF ."
INT
In such case, after setup of the chain play list,
reset the Chain Play Mode to " ON " .
59
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
OL
BIT
24
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
23
24
OL
BIT
24
0
3
FS
6
9
kHz
12
CLOCK
18
24
INT
30
42
23
24
OL
24
BIT
0
3
FS
6
9
kHz
12
18
CLOCK
24
INT
30
42
23
24
OL
24
BIT
0
3
FS
6
9
kHz
12
CLOCK
18
24
INT
30
42
23
24
Advertisement
Chapters
Table of Contents
