Duplicating A Program - Fostex D2424LV Reference Manual

Model D2424LV Reference Manual (Handling Programs)
To enter a title:
• Turn the Jog dial, or pressing the [NEXT] key and
[PREV] key for the flashing cursor to voluntarily input
alphanumerics.
Press the [PREV] key/[NEXT] key and the recorder will
jump to the letters/symbols listed below (small square
position).
• Move the flashing cursor with the Shuttle dial.
• You can input the following alphanumerics and
symbols.
Titles can contain up to 16 alphanumeric characters.
Any program content (Recording data/various setup items) can be duplicated but with a separate
program number.
<Notes>
* Duplicating a program is possible only when the Multiple Undo function is set to ON when formatting the
current drive. In a current drive with this setting at OFF, the " PGM Duplicate? " message will not display when
pressing the [EDIT] key mentioned below.
* The program which can be duplicated must be the currently active program.
Therefore, the program you wish to duplicate must be activated prior to executing the duplicating mode.
1. With this recorder in the stop mode, press the
[EDIT] key to display "PGM Duplicate?" ("?"
flashes).
OL
0
3
6
9
12
18
24
30
42
1 2 3 4 5 6 7 8 9 10 11 12
2. Press the [EXECUTE/YES] key.
As an example, the following is displayed and "SURE?"
will flash. This means that program 01 will be duplicated
for program 05, the new program 05. Refer see <Note>
below.
Flashing
SURE?
OL
0
3
6
9
12
18
24
30
42
1 4 5 6 7 8 9
2 3 10 11 12

Duplicating a Program

Flashing
OL
BIT 24
0
3
6
9
12
CLOCK
18
24
INT
30
42
13 14 15 16 17 18 19 20 21 22 23 24
OL
BIT 24
0
3
6
9
kHz
12
CLOCK
18
24
INT
30
42
13 14 15 16 17 18 19 20 21 22 23 24
6. When you finish entering the title, press the
[EXECUTE/YES] key.
Program 2 (PGM 02) and its title are set.
The display shows the ABS Time Base indication of the
Program.
7. Press the [EXIT/NO] key, or [STOP] button.
<Important!>
• When you create a new Program by selecting the
" New PGM ? " menu, a new Program is created with
an increment number.
That is, if only one Program exists and when you
create a new Program, it will be named Program
2. If Programs 1-5 already exist, a new Program
number will be 6.
• Remember that producing new programs
gradually decreases recordable disk space.
If disk space is insufficient, or if 99 programs have
already been created, you cannot create more new
programs.
If a new program is attempted, " Can't New PGM! "
will indicate that the operation is invalid.
<Note>
The program to be duplicated will be assigned with a
program number following that of the program
presently existing in the disk.
If " Duplicate P01 > 05 " is displayed as in the previous
example, this indicates that four programs presently
exist in the disk and that the new program will be
FS
kHz
number 05.
If the duplicated program is to be checked or you wish
to switch to this program, refer to the next item
" Selecting a program ."
3. Press the [EXECUTE/YES] key again.
The display will change to head of the duplicated
original program (P01 in this example), and
"COMPLETED!" will light.
4. Press the [EXIT/NO] key (or [STOP] button).
"COMPLETED!" will be extinguished.
FS
By following these procedures, the same content in
program 01 is duplicated in program 05.
36