Lucent Technologies PARTNER Advanced Communications System Release 1.0 System Planner Manual page 13

Button Feature Summary
This section lists button features in order by feature type and feature name.
For each feature, the first line shows the following information:
The name of the feature.
Whether a button with lights is required (
An abbreviation that can be entered on the Form C templates.
The entries needed to program the feature on a button. Some features can
include a two-digit extension number (shown as
g
number (shown as ).
Extension 10 Features
These features can be assigned only to the phone at extension 10. Auto dialing
and dial-code features can also be used at extension 10; of particular interest
are the Intercom Auto Dialing and Manual Signaling features, which use button
lights to show extension calling activity.
Night Service Button
Turns Night Service on and off. Phones in the Night Service Group ring immediately
when the feature is active, regardless of normal ringing. To use Night Service,
extension 10 must be programmed with a Night Service button. Night Service Group
extensions should be identified on Form B2.
Outgoing Call Restriction Button
Allows the user at extension 10 to change the outgoing call restriction for a particular
extension. An Auto Dial button with lights must be programmed for each extension to
be changed.
Wake Up Service Button
Allows the user at extension 10 to schedule an intercom call to a target extension at a
designated time. If Music on Hold {#602} is active, music is played when the phone is
answered; otherwise, nothing is heard.
) or recommended ( ).
xx
) or a single-digit group
NightSvc {#503}
OCR {#114}
Wake {#115}
Auto Dialing Features
Auto Dial numbers can include the digits
that you store by pressing h
(Touch-Tone Enable). To store an intercom number, you must press the
&
left i button before entering the extension number. Only one Auto Dial
number for an extension can be stored on the buttons available at an extension
for both the phone and Intercom Autodialer.
Auto Dialing (Outside Phone Number)
Places a call to an outside telephone number. Outside telephone numbers can be
up to 28 digits. If a dial-out code is required to dial outside numbers (for example, on
PBX or Centrex lines), include it in the stored number followed by pauses, if
necessary.
Auto Dialing (PBX/Centrex Feature Code)
Dials a PBX/Centrex feature code. To program the button so the user can access
the feature while on a call, specify "R" on Form C before the feature code, and
include the Recall signal on the Auto Dial button.
Fax Management
Transfers calls to the fax machine at the designated extension with one touch. If on
a button with lights, the lights show when the fax is busy or when it is having trouble
and not answering—for example, when it is out of paper.
Intercom Auto Dialing—Ring
Places a ringing intercom call to an extension, or transfers a call. If on a button with
lights, the lights show calling activity at the destination extension.
Intercom Auto Dialing—Voice Signal
Places a voice-signaled intercom call to the extension's phone speaker, or transfers
a call with a voice-signaled announcement. If on a button with lights, the lights show
calling activity at the destination extension.
Manual Signaling—Ring
Beeps the designated extension. If the user presses
places a ringing intercom call to the extension, or transfers a call. If on a button with
lights, the lights show calling activity at the destination extension.
Manual Signaling—Voice Signal
Beeps the designated extension. If the user presses
places a voice-signaled intercom call to the extension, or transfers a call with a
voice-signaled announcement. If on a button with lights, the lights show calling
activity at the destination extension.
0 – 9 , * , # , and special functions
(Pause), ! (Stop), S (Recall), and
xxx-xxxx
xxx
xx
Fax-
i
xx
Ext-
i
xx
ExtVS-
i*
xx
f13
MS-
i first, pressing the button
xx
f13*
MSVS-
i first, pressing the button
(NAME)
xx
xx
xx
xx
xx
11