Audio Delay - Marantz NR1403 Owner's Manual

Audio Delay

While viewing video, manually adjust the time to delay audio output.
0ms – 200ms
• This item can be set within the range of 0 to 100 ms when "Auto Lip Sync" (vpage 65) is set to
"On" and when a TV compatible with Auto Lip Sync is connected.
• Store "Audio Delay" for each input source.
Volume
Set the volume setting.
Setting items
Scale 0 – 98 : Display in the range 0.5 (Min) to 98.
Set how volume is –79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
displayed.
The "Scale" setting is applied also to the "Limit" and "Power On
Level" display method.
Off : Do not set a maximum volume.
Limit
Make a setting for 60 (–20dB) / 70 (–10dB) / 80 (0dB)
maximum volume.
Power On Level Last : Use the memorized setting from the last session.
Define the volume setting Mute : Always use the muting on condition when power is turned on.
that is active when the 1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.
power is turned on.
Mute Level Full : The sound is muted entirely.
Set the amount of –40dB : The sound is attenuated by 40 dB down.
attenuation when muting –20dB : The sound is attenuated by 20 dB down.
is on.
Default settings are underlined.
Setting details
Default settings are underlined.
Setting details
Audyssey
Set Audyssey MultEQ ® , Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . These can be
selected after Audyssey ® Setup has been performed. For additional information on Audyssey technology,
please see page 89.
NOTE
• If you have not performed Audyssey ® Setup, or if you change the speaker settings after performing
Audyssey ® Setup, you may not be able to select Dynamic EQ ® /Dynamic Volume ® .
In this case, either perform Audyssey ® Setup over again or perform "Restore..."
return to the settings after Audyssey ® Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the "Audyssey"
cannot be set.
Setting items
MultEQ ®
Audyssey : Optimize the frequency response of all speakers.
MultEQ ® compensates for
Audyssey Byp.L/R : Optimize frequency response of speakers except
both time and frequency front L and R speakers.
characteristics of the Audyssey Flat : Optimize frequency response of all speakers to flat
listening area based on response.
Audyssey ® Setup
Manual EQ : Apply frequency response set with "Manual EQ"
measurement results. (vpage 63).
Off : Turn "MultEQ ® " equalizer off.
Selection is done from three
types of compensation
curves. We recommend the
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
"Audyssey" setting.
selected after Audyssey ® Setup has been performed. "Audyssey"
MultEQ ® is the prerequisite
is automatically selected after performing Audyssey ® Setup. When
function for Dynamic EQ ®
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected,
and Dynamic Volume ® .
• After running Audyssey ® Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only
• This can also be set by pressing
Each time
changed as shown below.
NOTE
When using headphones, "MultEQ ® " is automatically set to "Off".
"MultEQ ® ", "Dynamic EQ ® " and "Dynamic Volume ® " settings are stored for each input source.
61
Default settings are underlined.
Setting details
illuminates.
MultEQ
.
MultEQ
is pressed, the setting is
Audyssey Audyssey Byp.L/R
Off Manual EQ Audyssey Flat
Audio
(vpage 27) to
illuminates.