Table of Contents
Advertisement
Shooting
Adjusting Audio Input
Settings and Recording
Level
You can record audio from the two channels (CH-1/CH-2) in
synchronization with video images on this camera recorder.
The camera recorder is equipped with [INPUT1] and
[INPUT2] terminals for audio input. You can select a
recording channel and the adjustment mode (manual/
automatic).
[INPUT1/INPUT2] Terminal
Setting Audio Input
Select the audio to input through [INPUT1] and [INPUT2]
terminals with the [AUDIO INPUT 1/2] mode switch.
[LINE]
Use this setting when connecting to an audio device or
other equipment. The reference input level is +4 dBu.
[MIC]
Use this setting when connecting to a dynamic
microphone.
[MIC+48V]
Use this setting when connecting to a microphone
(phantom microphone) that requires a +48 V power
supply.
Note :
● When connecting a device that does not require a +48 V
power supply, make sure that it is not set to the MIC+48V
position.
● When the [AUDIO INPUT 1/2] mode switch is set to MIC ,
make sure that a microphone is connected to the [INPUT1/
INPUT2] terminal. If you increase the recording level when a
microphone is not connected, noise from the input terminal may
be recorded.
● When a microphone is not connected to the [INPUT1/
INPUT2] terminal, set the [AUDIO INPUT 1/2] mode switch
to LINE or adjust the volume with the [CH1/CH2 AUDIO
LEVEL] recording level adjustment knob.
Memo :
● Set the reference input level of MIC and MIC+48V using
[Input1 Mic Ref.]/[Input2 Mic Ref.] in the [Main
Menu]B[Record Set]B[Audio Set] menu. (A Page 72)
Setting of [CH-2 INPUT] Selection Switch
Use the [CH-2 INPUT] selection switch to select the audio to
be recorded to CH-2.
[INPUT1]
Records audio from [INPUT1] terminal to CH-2.
[INPUT2]
Records audio from [INPUT2] terminal to CH-2.
[CH-2 INPUT] Selection Switch
[AUDIO INPUT 1/2]
Mode Switch
Adjusting Audio Recording Level
You can select to adjust the audio recording levels for the two
channels (CH-1/CH-2) manually or automatically.
[AUDIO LEVEL
CH-1/CH-2]
Adjustment Knob
Manual Adjustment Mode (Manual
Adjustment)
Set the [AUDIO SELECT CH-1/CH-2] switch on the camera
recorder to MANUAL to enter the manual adjustment
mode, and use the [AUDIO LEVEL CH-1/CH-2] adjustment
knob to set the recording level.
You can adjust the level manually during the recording,
recording pause, and stop modes.
1
Set the [AUDIO SELECT CH-1/CH-2] switch to
MANUAL for the channel to manually adjust the
recording level.
2
Turn the corresponding [AUDIO LEVEL CH-1/CH-2]
adjustment knob to adjust the level.
Adjust such that the audio level meter does not light up at -2 dB
even for loud sounds.
1280x720
30/24 fps
24p HQ
A
100min
ND1/16 A<3200K>
B
100min
F5.6
AE+1 9dB 1/10000
STBY
282min
STATUS 1 Screen
Memo :
● Set [Audio Limiter] in the [Main Menu]B[Record Set]B[Audio
Set] menu to On to activate the audio limiter in the Manual
Adjustment Mode. This controls the recording level when
excessive audio signals are input. (A Page 72)
● For the reference level to be recorded on SDHC cards, set
[Audio Ref. Level] in the [Main Menu]B[Record Set]B[Audio
Set] menu to -20dB or -12dB . (common for CH-1, CH-2)
(A Page 72)
[FULL AUTO] Switch
When the LCD monitor is open
[AUDIO SELECT CH-1/
CH-2] Selection Switch
0 0 : 0 0 : 0 0 : 0 0
MAX 123%
MIN
45%
SKIN AREA
S.DTL
B -3
Audio Level Meter
-2 dB
Advertisement
Table of Contents
