Installing The Stand Or Removing The Stand Column; Installing The Stand - Dynex DX-32L100A11 User Manual

Installing the stand or removing the stand column

• If your TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions because incorrect adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore your TV to its normal
operation.
• If your TV has been dropped or damaged in any way.
• When your TV exhibits a distinct change in performance.
Outdoor antenna grounding
If an outside antenna or cable system is connected to your TV, make sure
that the antenna or cable system is grounded to provide some
protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA No. 70, provides
information with respect to correct grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of the
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
7
Antenna lead-in wire
1
Grounding clamp
2
Antenna discharge unit
3
Grounding conductors
4
Ground clamps
5
Power service grounding electrode
6
system
Electric service equipment
7
Note to CATV system installer
Article 820 of the National Electrical Code, ANSI/NFPA No. 40 provides
guidance for correct grounding. Specifically, it states that the cable
ground must be connected to the grounding system of the building as
close to the point of cable entry as practical.
Condensation
Moisture will form on the TV if the TV is brought from cool surroundings
into a warm room or if the temperature of the room rises suddenly.
When this happens, the TV's performance may be impaired. To prevent
this, let the TV stand in its new surroundings for about an hour before
switching it on, or make sure that the room temperature rises gradually.
Condensation may also form during the summer if the TV is exposed to
the breeze from an air conditioner. In such cases, change the location of
the TV.
Mobile telephone warning
To avoid interference with your TV picture and sound, operating
problems, or even damage, keep your cordless and cellular telephones
away from the TV.
End of life directives
Your TV contains tin-lead solder and a fluorescent lamp containing a
small amount of mercury. Disposal of these materials may be regulated
for environmental reasons. Your TV also contains material that can be
recycled and reused. For disposal or recycling information, contact your
local authorities or the Electronic Industries Alliance at www.eia.org to
find a recycler in your area.
Non-active pixels
The LCD panel contains almost 3 million thin film transistors, which
provide exceptionally sharp video quality. Occasionally, a few
non-active pixels may appear on the screen as a fixed blue, green, or red
point. These non-active pixels do not adversely affect the performance
of your TV, and are not considered defects.
Installing the stand or removing
the stand column
Cautions
1
2
3
4
5
6
You must install your TV into the stand in order for it to stand upright on
a cabinet or other flat surface. If you intend to mount your TV on a wall
or other vertical surface, you must remove the stand column.

Installing the stand

You must install the stand to use the TV in an upright position on a flat
surface.
To install the stand:
Table edge
• Read these instructions carefully before you try to assemble the
stand or remove the stand column.
• Make sure that you handle the TV carefully when attempting to
assemble or remove the stand. If you are not sure of your ability
to do this, contact a professional installer or service technician.
Dynex is not responsible for any damages or injuries that occur
because of mishandling or incorrect assembly.
• Use a soft cushion or covering to prevent scratching or damage to
the TV screen or cabinet.
• The speaker is not intended to support the weight of the TV. Do
not move or handle the TV by the speaker. This can cause damage
that is not covered by your warranty.
• Before assembly or removal of the stand, unplug the power cord.
Note: Your TV may differ from the illustrations shown.
1 Remove the stand from the box and place it on a table or bench.
2 Lay the TV (screen down) on the edge of the table or bench. Make
sure that you put a soft cloth or cushion between the table or
bench and the TV.
Stand column
3
DX-32L100A11
Stand