Rs-232C - Panasonic PTDZ8700U - DLP PROJECTOR Operating Instructions Manual

PROJECTOR SETUP menu
Press ▲▼ to select [TIME] or
4 )
[COMMAND] and change the setting
according to the instructions of the
menu.
Set the time at which the command
will be executed using ▲▼ or numeral
TIME
buttons.
Select a command to execute at the
set time from the following.
•
POWER ON
•
STANDBY
•
SHUTTER
OPEN
•
SHUTTER
COMMAND
CLOSE
•
INPUT RGB1
•
INPUT RGB2
•
INPUT VIDEO
•
INPUT S-VIDEO
•
INPUT DVI-D
•
INPUT HDMI
Û
: PT-DZ8700U/PT-DS8500U only
Press ▲▼ to select [STORE] and
5 )
press <ENTER> button.
Note
z
If you try to register a setting that would cause the
lamp to flash for a short time, an error message will be
displayed on the screen. Set the [TIME] and [COMMAND]
again.
z
To delete a command which has been set, press
<DEFAULT> button.
z
If multiple commands have been set for the same time,
they are executed in chronological order starting from the
smallest command number.
z
The setting time operates under the local time.
Æ
( page 84)
z
If an operation is executed with the remote control or
control panel of the projector or with a control command
before the command set in the schedule is executed, the
command set with this function may not be executed.

RS-232C

This sets the communication parameters at the serial
terminals.
Press ▲▼ to select [RS-232C].
1 )
2 ) Press <ENTER> button.
z
The [ RS-232C] screen will be displayed.
Press ▲▼ to select communication
3 )
conditions.
press ◄► to change the setting.
4 )
Note
z
Refer to "Serial terminal" (
82
- ENGLISH
•
Û
INPUT SDI
•
LAMP POWER
HIGH
•
LAMP POWER
LOW
•
LAMP DUAL
•
LAMP SINGLE
•
P IN P OFF
•
P IN P USER1
•
P IN P USER2
•
P IN P USER3
Æ
page 117).
J
Selecting items in [EMULATE]
When using the control commands for one of our
projectors that you have previously purchased to
control this projector using a computer via its serial
input terminal, set up the EMULATE function as
follows. This will allow you to use the control software
etc. designed for our existing projectors.
1. Select [EMULATE] in step 3).
2. Press <ENTER> button.
Press ▲▼ to select the required item.
3.
4. Press <ENTER> button.
DZ8700 Series, DS8500 Series,
DW8300 Series, D5000 Series,
● DEFAULT
D6000 Series, DW6300 Series,
DZ6700 Series, DZ6710 Series
D9510 Series, D9610 Series,
D9610
D9500 Series, D9600 Series,
SERIES
D8500 Series, D8600 Series
D7700 D7500 Series, D7600 Series,
SERIES D7700 Series, DW7000 Series
L6500 L6500 Series, L6510 Series,
SERIES L6600 Series
J
About [EMULATE SETTING]
This sets which input signal can be selected using the
input signal change command when a projector of a
specific model is used with the emulate function.
1. Select [EMULATE SETTING] in step 3).
2. Press <ENTER> button.
z
The [EMULATE SETTING] screen will be
displayed.
Q
When the D9610 Series is selected
Press ▲▼ to select input signal
1.
[VIDEO], [S-VIDEO], [RGB1], [DVI-D] or
[SDI].
z
[RGB2] and [HDMI] cannot be selected.
z
[SDI] is not shown for PT-DW8300U.
Press ◄► to select the input signal
2.
change command to be assigned to
the selected input signal.
z
Selectable input signal change commands
When RGB1 is selected:
[INPUT1], [INPUT2], [INPUT3], [INPUT
RGB], [NONE]
For all other instances:
[INPUT1], [INPUT2], [INPUT3], [NONE]
z
The same input signal change command
cannot be assigned to multiple input signals.