Hayward Super Pump Owner's Manual

Hayward Super Pump Owner's Manual

Super pump series

Advertisement

__________________________________________________________________________________________
*50HZ Models are not UL or CSA Listed.
TM
The Hayward Super Pump
is equipped with large capacity filters, heaters, and pool cleaning equipment. The Super is a self-priming pump that incorporates an
improved seal and impeller design that will provide many years of efficient, dependable, corrosion-free service. The advanced design
provides superior performance while reducing maintenance requirements.
To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.
WARNING –
CAUTION –
ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE
INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER
OF THIS PRODUCT. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY.
WWW.HAYWARDPOOL.COM
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Super Pump
is specifically engineered for the demanding requirements of today's in-ground swimming pool/spa that
This product should be installed and serviced only by a qualified professional.
A licensed electrician MUST complete, in full, all electrical installations noted in this manual.
SAVE THIS INSTRUCTION MANUAL
Use of non-Hayward replacement parts voids warranty.
HAYWARD POOL PRODUCTS, INC.
620 DIVISION STREET ELIZABETH, NJ 07207 (908) 351-5400
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Series
WWW.HAYWARDPOOL.COM
P/N: ISSPSERIES
REV. A

Advertisement

Table of Contents
loading

Summary of Contents for Hayward Super Pump

  • Page 1 A licensed electrician MUST complete, in full, all electrical installations noted in this manual. SAVE THIS INSTRUCTION MANUAL Use of non-Hayward replacement parts voids warranty. ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT.
  • Page 2 Pool and spa components have a finite life. All components should be inspected frequently and replaced at least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 3 - In addition to two or more suction outlets per pump installed in accordance with latest IAF (formerly NSPI) standards and CPSC guidelines, follow all national, state, and local codes applicable. - Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 4 Failure to install according to all defined instructions may result in severe personal injury or death. General Information Introduction This manual contains information for the proper installation and operation of the Hayward Super Pump Series. The instructions in this manual MUST be followed precisely. Failure to install according to defined instructions will void warranty.
  • Page 5 IMPORTANT NOTES – No system should allow any higher than 8-ft/sec [2.44 meters/sec] water velocity. It is recommended that a minimum length of piping, equivalent to 10 pipe diameters, be used between the pump suction inlet and any plumbing fittings. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 6 H.P. (KW) rating and distance from the power source. NOTE - All electrical wiring MUST be performed by a licensed electrician, and MUST conform to local codes and NEC regulations. Use copper conductors only. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 7 1. STOP PUMP before proceeding. 2. CLOSE VALVES in suction and outlet pipes. 3. RELEASE ALL PRESSURE from pump and piping system using filter manual air relief valve. See filter owner’s manual for more detail. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 8 Keep motor clean. Insure air vents are free from obstruction to avoid damage. Do NOT use water to hose off motor. Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine Hayward seal assembly kit. See “Shaft Seal Change Instructions” in this manual.
  • Page 9 To reduce risk of injury, do not permit children to use this product. B. Disconnect all electrical power service to pump before beginning shaft seal replacement. C. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions.
  • Page 10 15. Fasten assembly to pump/strainer housing using the four (4) 3/8”" x 2" housing cap screws. (Be sure housing gasket is in place, and replace if damaged). Tighten alternately and evenly. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 11 SPX1600J SPX1600J SPX1600J SPX1600J MOUNTING FOOT ADAPTER SPX2600Q SPX2600Q SPX2600Q SPX2600Q SPX2600Q SPX2600Q SLINGER SPX0125F SPX0125F SPX0125F SPX0125F SPX0125F SPX0125F MOTOR-60 CYCLE SINGLE PHASE [WILL INCLUDE SLINGER(20)] SPX1600Z1M SPX1605Z1M SPX1607Z1M SPX1610Z1M SPX1615Z1M SPX1620Z1M WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
  • Page 12 Solution: Contact qualified professional to check that the wiring gauge is heavy enough. NOTE Your Hayward pump motor is equipped with an “automatic thermal overload protector.” The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The “thermal overload protector”...
  • Page 13 4. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. Solution: All seal leaks should be replaced at once. © Hayward Pool Products, Inc. 2005 All rights reserved. WWW.HAYWARDPOOL.COM...
  • Page 14 To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service center information, contact Hayward customer service department. No returns may be made directly to the factory without the express written authorization of Hayward Pool Products, Inc.
  • Page 15 Series Page 15 of 15 ▼DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation. ------------------------------------------------------------------------------------------------------------ Mail to: Hayward Pool Products, Inc., 620 Division Street, Elizabeth, NJ 07207, Attn: Warranty Dept. Warranty Registration Card □ □...

Table of Contents