Page 1
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY. *Only units equipped with 3' twist-lock cords are UL-listed. SAVE THIS INSTRUCTION MANUAL HAYWARD POOL PRODUCTS, INC. Corporate Headquarters: U.S.A: 620 Division Street 1 Hayward Industrial Drive 2935 Sidco Drive 2875 Pomona Blvd.
Page 2
™ Power-Flo Matrix Pump Series ____________________ PRODUCT REGISTRATION (Retain For Your Records) DATE OF INSTALLATION ____________________ INITIAL PRESSURE GAUGE READING (CLEAN FILTER) _______________________ PUMP MODEL ________________ HORSEPOWER _______________________ FILTER MODEL ________________ SERIAL NUMBER _______________________ IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury.
Page 3
™ Power-Flo Matrix Pump Series __________ ________________________ NOTE: The National Electrical Code (NEC) permits use of a cord with a maximum 3 ft. (1 m) length. If your pump is equipped with a cord complying with the NEC, the following three (3) items apply.
Page 4
Dimensions General Information Introduction This manual contains information for the proper installation and operation of the Hayward Power-Flo Matrix™ pump. The instructions in this manual MUST be followed precisely. Product Features The Above-ground industry’s largest above-ground strainer basket for large debris collection with minimal maintenance.
Page 5
™ Power-Flo Matrix Pump Series ____________________ Installation Instructions (cont.) Pump Location (cont.) Install pump on a firm, level base or pad to meet all local and national codes. The field supplied base or pad must be level and vibration-free. Though the pump is designed for outdoor use, it is strongly advised to protect the electrical components from the weather.
Page 6
™ Power-Flo Matrix Pump Series ____________________ Installation Instructions (cont.) Electrical (cont.) Voltage Voltage at motor MUST NOT be more than 10% above or below motor name plate rated voltage, or motor may overheat, causing overload tripping and reduced component life. If voltage is less than 90% or more than 110% of rated voltage when motor is running at full load, consult power company.
Page 7
Small children using pool MUST always have close adult supervision. Selecting Pump’s Discharge Position (4 Steps) Your Hayward Power-Flo Matrix™ pump can be easily positioned for horizontal or vertical water discharge. Step 1: Remove ALL plumbing attached to pump. Remove pump from base (if applicable).
Page 8
– B. Disconnect all electrical power service to pump before beginning shaft seal replacement. C. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions. D. The National Electrical Code requires either a three (3) foot maximum twist-lock cord set with a GFCI protected receptacle or hard wire (conduit) connection for swimming pool pump installation.
3. Mechanical binding and electrical overload. NOTE: Your Hayward pump motor is equipped with an “automatic thermal overload protector.” The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The “thermal overload protector”...
Page 10
Clean strainer basket regularly. Do NOT strike basket to clean. Inspect strainer cover gasket regularly and replace as necessary. Hayward pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary. Keep motor clean. Insure air vents are free from obstruction.
Page 11
™ Power-Flo Matrix Pump Series ___________________ Replacement Parts Parts Diagram Parts Listing Ref. No. Part No. Description Ctn. Qty. No. Req’d SPX5500D Strainer Cover with Lock Ring & 'O' Ring SPX5500H Strainer Cover 'O' Ring SPX5500F Strainer Basket SPX5500G Strainer Retainer/ 'C' Clip SPX5500C Strainer Housing SPX1700FG...
Page 12
To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service center information, contact Hayward customer service department. No returns may be made directly to the factory without the express written authorization of Hayward Pool Products, Inc.
Need help?
Do you have a question about the PowerFlo Matrix and is the answer not in the manual?
Questions and answers
Pump leaks while running
How to switch outlt on nre hayward pump