Timers Menu; Start/Stop Superchlorination; Program A Timeclock; Program A Countdown Timer - Hayward Pro Logic Operation Manual

Note: Separate chlorinator output levels for the pool and spa must be set. If the valves are in
the pool-only or spa spillover positions, then the chlorinator will operate according the pool
setting. If the valves are in the spa-only position then the chlorinator will operate according to
the spa setting. The actual amount of chlorine introduced into the pool/spa is determined by:
this output setting, the amount of time the filter pump is running, the water temperature, and
the amount of salt in the water. Also see Start/Stop Superchlorination.

Start/Stop Superchlorination

1. Press the "MENU" button repeatedly until "Settings Menu" is displayed
2. Press the ">" button repeatedly until "Super Chlorinate" is displayed.
3. The display will show whether superchlorination is "on" or "off".
4. Press "+" or "-" to toggle between "on" and "off"
Note: Once started, superchlorination will run for the programmed number of hours (Timers
Menu/Super Chlorinate Hours) or until you manually turn it off. Superchlorination may be
temporarily interrupted for a programmed spa operation.

Program a Timeclock

1. Press the "MENU" button repeatedly until "Timers Menu" is displayed
2. Press the ">" button repeatedly until "xxx—all" or "xxx—wkend" (where xxx is the parameter that
you want to program) is displayed.
3. Use the "+" and "-" buttons to set the desired start time, then press ">" to switch to the off time. Use
the "+" and "-" buttons to adjust the off time. If you are setting the "weekend" timeclock, press ">" to
go to the "weekday" settings.
Note: During the programmed time, there may be other automatic or manual operations that
prevent the relay/valve from operating—see a more detailed discussion under Automatic Sys-
tem Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diagnostic Information.

Program a Countdown Timer

1. Press the "MENU" button repeatedly until "Timers Menu" is displayed
2. Press the ">" button repeatedly until the "xxx—Timer" (where xxx is the parameter that you want to
program) is displayed.
3. Use the "+" and "-" buttons to set the desired timer period.
Note: A setting of 0:00 will display as "manual on/off". The countdown automatic turn off
function is disabled but manual operation is still permitted. There may be other automatic or
manual operations that prevent the relay/valve from operating—see a more detailed discussion
under Automatic System Operation/Timers Menu/Aux Timeclock or in Troubleshooting/Diag-
nostic Information.
Enter/Exit Service (or Service—Timed) Mode
1. Go to Pro Logic main unit (normally mounted near the pool equipment)
2. Pressing the "Service" button rotates through normal operation (red LED off), service mode (red
LED on continuously) and service-timed mode (red LED flashing).
Note: This operation can only be performed at the main Pro Logic unit. Both "Service" and
"Service-Timed" disable all automatic programmed operations and allow manual operation
from the main unit only. The buttons on the remote display/keypads will still be able to turn
equipment off in case of an emergency, but will not turn any equipment on. If the system is in
"Serviced-Timed" it will automatically switch back to normal operation at the end of the 3
hour time period.
25
Teach Wireless Push to start process
+ to start
Move to previous/next menu item
Press and hold
Press any button on wireless remote
wireless button
Move to previous/next menu item
Teach Wireless
Move to previous/next menu item
Successful
Teach Wireless
Move to previous/next menu item
NOT Successful
Teach Wireless
Move to previous/next menu item
Base NOT Found
This menu will only appear if a wireless base station is connected to the Pro Logic. Perform this
procedure each time a wireless remote control is added to the Pro Logic system. During this procedure
the wireless remote "learns" and remembers the ID code for the wireless base station connected to this
particular Pro Logic unit and will reject messages with any other ID codes. If "Base NOT found" is
displayed, then the Pro Logic can not communicate with the transmitter/receiver base station attached
to the main unit. If "NOT Successful" is displayed, then the base station did not receive a signal from
the remote control. This may be due to the distance between the Base Receiver and the remote device
being too great or may be due to interference caused by other RF equipment operating in the neighbor-
hood. Try changing the channel and then repeat the "Teach Wireless" command.
Change the desired wireless channel (1 - 5)
Wireless
If channel is changed, move to confirmation menu
Channel: 1
If channel is not changed, move to previous/next menu item
Confirm Change:
Push to confirm the channel change
+ to proceed
Move to previous/next menu item
Reteach all
Move to previous (Teach Wireless) menu
wireless units
This setting changes the channel to be used by the wireless base station and remote(s). If the channel
is changed and confirmed, all of the wireless remotes will have to be retaught. This menu will only
appear if a wireless base station is connected to the Pro Logic.

Timers Menu

The Timers Menu allows you to set all timeclock and countdown timers which control the automatic operation of
your pool/spa system.
Each timeclock has a single on/off program per day. All of the timeclocks are setup (Configuration Menu) either as
"all days" or "weekends/weekdays". If "weekends/weekdays" are selected, you will need to program on times for
both weekdays and weekends and off times for both weekdays and weekends, even if you want them to be the
same. All times are adjusted in 15 minute increments (9:00A, 9:15A, 9:30A, etc.). If you program the on time
equal to the off time ("10:00A to 10:00A") the output will NEVER turn on. If you want to disable a timeclock, you
can set the on time equal to the off time and you will notice the times disappear and the display simply shows "Off".
If, at a later time, you wish to re-activate the timeclock, simply press either the "+" or "-" buttons to go back to a
normal timeclock programming display.
The Countdown timer is programmed in increments of 5 minutes from "Manual On/Off" (0 minutes) to a maximum
of "21:00" (21 hours). When "Manual On/Off" is displayed, the countdown timer is disabled and the output will be
manually controlled. When a countdown timer is equal or greater than "0:05", pressing the appropriate output
button will turn the output on and start the timer. Pressing the button again will turn the output off or, when the
programmed time has elapsed, the output will automatically turn off.
10