STEPS IN CONFIGURATION .................. 2 1. START UP ........................ 3 1.1 I ..................... 3 NTRODUCTION 1.2 F ................3 EATURES AND SPECIFICATION 1.3 A ................4 CCESSORIES AND EQUIPMENT 1.4 A ......................5 PPEARANCE 1.4.1 3802 ......................5 1.4.2 3804 ......................6 1.4.3 3806 ......................
Page 3
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.15 C ......................46 OMMIT 3.16 R ......................47 EBOOT 4. COMMAND LIST ....................48 4.1 H ................. 48 YPER ERMINAL ETTING 4.2 C ....................51 OMMAND 4.2.1 [help] command..................51 4.2.2 [quit] command...................
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Steps in configuration To check out the peripheral equipments and STEP 1 understand the feature of this gateway. Please Start Up read this step very carefully before starting the configuring.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 1. Start Up 1.1 Introduction The WellGate FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your existing ADSL or cable modem service, which allows the use of a single, network for voice and fax services with consequent saving in network infrastructure and greatly reduced telephone charges.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 1.4 Appearance 1.4.1 3802 Front panel: The LED light provides system message of WellGate3802. Power : Light on means WellGate3802 is power on. L1-L2 : Light on means the line is in use. Link : Light on means WellGate3802 is connected to the network correctly.
Page 8
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 1.4.2 3804 Front panel: The LED light provides system message of WellGate FXO GateWay. Power : Light on means WellGate FXO GateWay is power on. L1-L4 : Light on means the line is in use. Link : Light on means WellGate FXO GateWay is connected to the network correctly.
Page 9
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 1.4.3 3806 Front panel: The LED light provides system message of WellGate3806. Power : Light on means WellGate3806 is power on. L1-L6 : Light on means the line is in use. Link : Light on means WellGate3806 is connected to the network correctly.
Page 10
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 1. Ethernet Port LAN/WAN: 10/100 Base-T; RJ-45 socket, complied with ETHERNET 10/100base-T. The pin-out is as following: PIN 1, 2: Transmit PIN 3, 6: Receive 2. COM: RS232 console port (DB-9pin male connector) Note: use straightforward cable to connect to your computer.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 PABX. 4. LINE: RJ-11 connector, FXO interface is for connecting the extension line of PABX or PSTN Line. 5. 12V DC: Input AC 100V~120V;output DC12V. 2. How to Setup and connect basically 2.1 System Requirement 1.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 2.2 IP Environment Setting User must prepare a valid IP address, complied with IP Network, for Gateway’s proper operation. For testing the validation of chosen IP address, using the same IP configuration in other PC or Notebook, and then try to connect to Public Internet (go to well-known website, receive Internet mail, or ping a specific public IP address).
Page 13
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 2.1: Network Configuration Select the Property of the LAN card. Setup the ip address, subnet mask and default gateway as below: Figure 2.2: Configure the network Click OK after you finished the network setup.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 The default ip address, netmask and default gateway address of the gateway is 10.1.1.3, 255.0.0.0, 10.1.1.254. 2.3 Network configurations in your gateway Key in the ip address of the gateway (http://10.1.1.3) with the browser Figure 2.3: WEB Browser...
Page 15
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 After key in the ip address, you have to enter the user name and password to enter the WEB configuration. (Username: root ; No password) Figure 2.3: Login the username and password You will enter the main page of the configuration after key in the login name and password correctly:...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 2.4: The main WEB configuration Press the Network Interface to configure the networking of your gateway: Figure 2.5: The Network Interface 2.3.1 Static ip address Please get the correct ip address, netmask and default gateway address from your ISP first. Press the OK button if you finished.
Page 17
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 2.5: Configure the static ip address Press the commit if you finish the configuration. Figure 2.6: Commit the data Press the reboot if you want the configuration executed.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 2.7: Reboot the system 2.3.2 DHCP mode Enable the DHCP if you are using the cable modem or DHCP server. Figure 2.8: Enable the DHCP function...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode Press the PPPoE Configuration and put the info of the PPPoE account and password in the configuration table.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Please make sure about the mode you want and follow up the step to configure your gateway. 2.4.1 Configure the gateway into the Peer-to-Peer mode Enter the H323 Configuration table and change the mode to Peer-to-Peer. Figure 2.10: Configure the Peer-to-Peer mode Press the OK button which is on the buttom of this page to save the configuration.
Page 21
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 2.11: Phone Book Example Figure 2.12: The example of Phone Book configuration This is the first record of Phone Book. So the index is 1 The name of the destination: test The E164 number (phone number) of the destination: 123 The ip address of the destination: 10.1.1.100...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Press the “Add Data” button when you finished, and the new table will display on the first index if you press the Phone Book configuration button. Figure 2.13: To show the Phone Book record Please Commit it and Reboot the system if the configuration is finished.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 2.14: Configure the GK info Press the OK button which is on the buttom of this page to save the configuration. Figure 2.15: Press OK to save the data Press the Commit Data and Reboot System buttons when you finished the configuration.
Page 24
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 registering on the Cisco GK. The Terminal type is needed if the endpoints want to register on the Cisco GK successfully. But all the configuration and function is the same if you set the gateway in Gateway or Terminal type.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3. Advance Configurations There are too many advanced commands for the advanced users. The following chapters are based on the application layer. Please get the info what you need. If you need the command, please watching the chapter of Command Line Interface.
Page 26
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Please configure your gateway just like below: Enter the IP address, Netmask and the default gateway in the network table. Please follow up your IP Sharing device. Figure 3.1: Network configuration Enable the ip sharing function and put the static ip address in the server address table.
Page 27
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.2: Enable the ip sharing function 1. Fixed IP – Please put the ip address of the ip sharing device in the IP Sharing Server Address table. 2. Dynamic IP – Just leave it if the IP sharing device is using PPPoE or DHCP protocol to connect with the internet.
Page 28
Release Feb, 2004 If the wan port of the ip sharing device is using the dynamic ip address, the gateway couldn’t get the ip address if the GK isn’t from Welltech. So the ip change is only support the GK from Welltech.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.2 Network Interface Users have to configure the Network configurations in this page. This gateway will be work while it is connecting with the internet network. Please get more info from the following descriptions. (see figure 3.4) Figure 3.4: Network Interface ...
Page 30
IP Change – Enable this function if the WAN IP address of the IP sharing device is dynamic address. The IP change function could support the GK from Welltech only. Please pay more attentions about this function if your IP sharing device...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.3 H323 Information This WEB page will help user to configure the information about the dial mode, GK information and some TCP/IP port for the communication. Please get more info about this configuration from the below detail descriptions.
Page 32
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Gatekeeper ID – The name of the GK. It has used with the Gatekeeper Discovery function. Support the GK mode only. RTP Port – The UDP port for the voice sending. RTP ports support a range of the UDP. The line 1 is using UDP(RTP) 16384 and (RTCP) 16385.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.4 System Configuration Figure 3.6: System Configuration Keypad Type – User could define the keypad for the DTMF sending. In-Band : The DTMF signal sending by RTP. ...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 IP side only. Please configure the Bureau table for the Hotline function if users pick up this service. Service 2 : The function is as same as the Service 1. ...
Page 35
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.7: Voice Setting Codec Priority – Users could define the priority of the codec in this table. If users just want only one codec, please pick up the codec you want in the 1 table and pick up the “nil”...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.6 Tone Pattern Users could configure the tone pattern of the gateway in this page. If the disconnect tone from PSTN side is match the one of the Busy tone table, the call will be dropped. (see figure 3.8)
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.8: Tone Pattern Busy Tone – To configure the frequency, level gain and on/off time for the busy tone from PSTN side. The busy tone supports 4 tables. ...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.9: Support Function T.38 FAX – Enable this function to support the FAX function. T.38 ECM – This function could support the error correction mode during the high-speed function.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.10: Phone Book Index – The list number of the Phone Book. Name – The name for this contact number. IP Address – The destination IP address for this phone number. ...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 service from the gateway. (see figure 3.11) Figure 3.11: TOS Configuration According to the RFC 1349 document, the TOS value as following : 1000 – minimize delay 0100 – maximize throughput 0010 –...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.12: Hotline Port – Pick up the port number first for the first step. Just enter the number in this table. Destination Address – Enter the destination IP address for this port. ...
Page 42
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.13: PPPoE Setting Device – Enable this device if users need the PPPoE connection. User Name – Put the PPPoE connection account in this table. Please get this info from your ISP.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.12 Password Users could define the password for the login account. The default password for the login account is empty. This gateway could support two-login account, one is “root” and another is “administrator”.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.14: Password root – Scroll the table to pick up the “root” account first and change the password for this account. administrator – Scroll the table to pick up the “administrator” account first and change the password for this account.
Page 45
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 3.15: ROM Upgrade TFTP/FTP server IP Address – Enter the server IP address for the firmware downloading. Target File name – Enter the name of the firmware file. ...
Page 46
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 DSP Test Image : This type will upgrade the test layer for the DSP. The file name for this type is like 483cbit.bin OK – Press the OK button to start the upgrade procedure. Please pick up the correct type for the file update or the gateway will be crashed.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.14 Flash Clean Figure 3.16: Flash Clean This WEB page will be shown if users use the “root” account for login. Press the “CLEAN” button will make all the settings back to the default factory setting.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 3.15 Commit Figure 3.17: Commit Please press the commit button after all the configurations finished. This just like the save action.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 4. Command List 4.1 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure Gateway. There are kinds of terminal emulator software. Here, we use Microsoft HyperTerminal to depict how to set up terminal emulator: Execute the Hyper Terminal program, and then the following windows will pop-up on the screen.
Page 51
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Figure 4.2: Edit the name of the connection After pressing OK button, the next window appear, and then choose COM1/2 Port, which you are going to use. Figure 4.3: Pick up the right interface to use Configure the COM Port Properties as following: ...
Page 52
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Flow control: None Figure 4.4: Configure the right Bps and control Press ‘OK’ button, and then start to configure Gateway.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 4.2 Command List 4.2.1 [help] command Type help or man or ? to list all the available command. 4.2.2 [quit] command...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Type quit will quit the WellGate FXO GateWay configuration mode. And turn back to login prompt. Note: It is recommended that type the “quit” command before you leave the console. If so, WellGate FXO GateWay will ask password again when next user connects to console port.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 4.2.5 [flash] command This command will clean the configuration stored in the flash rom and reboot WellGate FXO GateWay in factory default setting. Parameter Usage: -clean clean all the user-defined value, and reboot WellGate FXO GateWay in factory default mode.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Note: Users should use commit to save modified value, or they will not be activated after system reboot. 4.2.7 [ifaddr] command Configure and display WellGate FXO GateWay network information.
Page 57
(sysconf –cmcenter “IP address of management center”) Note: management center is optional software to help user can easily configure WellTech products, please contact your reseller to know more about it.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 FXO GateWay is behind a IP-sharing , user can enable IP sharing function and specify public IP address of IP-sharing. 4.2.8 [time] command When SNTP function of WellGate FXO GateWay is enabled and SNTP server can be found as well, type time command to show current network time.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 4.2.10 [greetrd] command This command is for user to record their own greeting and analyze disconnect tone. If WellGate FXO GateWay can’t hang up call and release line correctly, please use this function to analyze disconnect tone of PSTN side.
Page 60
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Disconnect Tone Analysis : please follow instructions on screen ; first call in line1 of WellGate FXO GateWay from PSTN side(now can’t hear greeting), hang up the phone and press “enter” to start record disconnect tone. Finally, choose “y/n” to save data analyzed or not.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 exit : exit this command 4.2.11 [pbook] command Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in peer-to-peer mode. When adding a record to Phone Book, users do not have to reboot the machine, and the record will be effective immediately.
Page 62
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 ------------------------------------------------------------------------------------------------- Parameter Usages: -print print out current contents of Phone Book. Users can also add index number, from 1 to 100, to the parameter to show specific phone number. Note: <index number>...
Page 63
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 -add add a new record to phone book. When adding a record, users have to specify name, ip, and e164 number to complete the command. -search search a record in phone book. The searching criteria can be name, ip, or e164.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 out IP address of 123. (1) If called party is FXO product, please set e164 of pbook as e.164 of called party, and remember to set sysconf –drule in_drop “e.164”(refer to 5.12.)in called party. (2) If called party is FXS product, please set e164 of pbook as prefix of called party, when dialing to different line of FXS product, please dial line number.
Page 65
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 ------------------------------------------------------------------------------------------------- Parameter Usages: -enable enable the DDNS function -server enter the server address of the DDNS server you use -hostname enter the domain name address which you get from the DDNS server key in your id...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 -passwd key in your password -checkIP enable or disable the check current user’s IP address -checkIPsrv1 enter the IP address of the check server -checkIPsrv2 the secondary IP address of the check server -delay service delay time -force...
Page 67
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 - service: 0 Dial In Service in Dial In Service, WellGate FXO GateWay will pick up incoming calls from PSTN,...
Page 68
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 play pre-recorded voice greeting or, and then have users to make a 2 dial to destination. 1/2 HotLine Service (this feature must be implemented after set bureau –table command) HotLine Service provides Hot Line function, which connects directly to pre-defined destination.
Page 69
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 ● drop: drop the dial digit. ● insert: insert the dial digit ● filter: filter the dial digit. Note: 1. out: Through WellGate FXO GateWay to dial out to another Gateway’s e164 number.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 available.) 4.2.15 [h323] command This command is to configure H.323 related parameters. ------------------------------------------------------------------------------------------------...
Page 71
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameters Usage: -print print current h323 related settings -mode alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer mode). If users select gatekeeper mode, a extra gatekeeper is need when WellGate FXO GateWay is in operation. to assign gatekeeper’s IP address when WellGate FXO GateWay is in gatekeeper mode.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 -e164 e164 number, which is registered as phone number in gatekeeper. -alias h323 ID, a identification in h323 world for other parties’ recognition. The field might be used as a key of authorization or accounting in some VoIP application. It is recommended to assign a special name, or it might conflict with other devices.
Page 73
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameters Usage: -print print current voice information and configurations. -send to define packet size for each codec. 20/40/60ms means to send a voice packet per 20/40/60 milliseconds. The smaller the packet size, the shorter the delay time.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 recommended. In this parameter, 20/40/60ms is applicable to G.711u/a law, and G.729a codec, while 30/60/90ms is applicable to G.723.1 codec. -priority codec priority while negotiating with other h323 device. This parameter determines the listed sequence in h.245 TCS message.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameter Usages: -print : display current TOS values configurations. -sigtype configure DSCP value of signaling packets from 0 to 63 -rtptype configure DSCP value of RTP packets from 0 to 63 Note: Users should be aware that TOS is effective only when network devices (for ex: router, switch..
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 4.2.19 [support] command This command provides some extra functions that might be needed by users. ----------------------------------------------------------------------------------------------------- Parameter Usages:...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 -print print current setting in support command. -t38 to switch ON/OFF (1 = ON; 0 = OFF) T.38 function.T.38 function is for FAX. If user will use FAX machines, please switch on T.38 function. -t38ecm to disable/enable T.38 error correction mode.
Page 78
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameter Usages: - print : display current grouping information - enable : enable grouping function - disable : disable grouping function - number : set how many groups will be divided - pattern : set how many members in each group - e164 : set e164 of each group For ex: if users need to divide WellGate FXO GateWay into L1 in the 1...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 4.2.21 [bureau] command Type bureau to display the command usage. -------------------------------------------------------------------------------------------------...
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameter Usages: - print: display bureau line information and configuration. ------------------------------------------------------------------------------------------------- - pstn: PSTN number (per port basis). This number is used to display as a caller ID when the caller ID is not available.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameter Usages: -print print current setting in prefix command. -pstnrule to do digit replacement of incoming call from PSTN side. Ex, to set prefix –pstnrule 1 123 456 which means the first set of PSTN side rule is: IF user press 123888 after dialing in WellGate FXO GateWay from PSTN side ,the real number dialed out will become 456888.
Page 82
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameter Usages: -print show versions of all rom files -app, boot, dsptest, dspcore, dspapp to update main Application program code, Boot code, DSP testing code, DSP kernel code, or DSP application code.
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 during 2M ROM file upgrading. Note: To set mac address please key in command setmac:(when key in MAC address ,press enter each time after key in two characters): ------------------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------------- -greeting The greeting file can be updated by users.
Page 84
FXO H.323 Gateway User Manual Document Ver.: 117b Release Feb, 2004 Parameter Usages: -passwd <login name> <password> Note: <login name> can be “root” or “administrator” only. “root” and “administrator” have the same authorization, except3 commands that can be executed by “root” only – “passwd –set root”, “rom –boot”, and “flash –clean”...
Need help?
Do you have a question about the FXO GATEWAY H.323 3802 - VERSION 117B and is the answer not in the manual?
Questions and answers