Tuner Operation; To Selecting The Tuner; Listening To The Tuner - Marantz AV8003 User Manual

ENGLISH
RECOVERY OF MEMORY
Recover backed up settings as follows.
Hold the MEMORY and MENU buttons on the front
panel simultaneously for at least 3 seconds.
AV PRE TUNER AV8003 AV PRE TUNER AV8003
UP UP
PURE DIRECT URE DIRECT HDMI HDMI
M-DAX M-DAX
DOWN DOWN
INPUT
VOLUME VOLUME
SELECTOR
SURROUND ZONE ZONE
MODE AUTO UTO ZONE ZONE SPEAKER SPEAKER MENU MENU EXIT EXIT BAND BAND T-MODE T-MODE MEMORY MEMORY CLEAR CLEAR
PURE E 7.1CH 7.1CH
THX THX TOP TOP M-DAX M-DAX DISPLAY DISPLAY
STANDBY DIRECT T INPUT INPUT
POWER ON/OFF
PHONES SETUP MIC SETUP MIC
ENTER ENTER
"MEMORY LOAD" is displayed and the unit's stored
settings are reapplied.
The unit temporarily enters standby mode. If there is
no backup data, "NO BACKUP" is displayed and no
data is recovered.
M E M O R Y L O A D
N O B A C K U P
Note:
• Because the following settings values are
not backed up, each Volume value is set to
Minimum.
• Main Zone Volume
• Zone Volume
• Zone Speaker Volume
48

TUNER OPERATION

TO SELECTING THE TUNER

(Using the unit)
AV PRE TUNER AV8003
PURE DIRECT PURE DIRECT
M-DAX M-DAX
INPUT INPUT
SELECTOR SELECTOR
SURROUND SURROUND ZONE ZONE
MODE MODE AUTO AUTO ZONE ZONE SPEAKER SPEAKER MENU EXIT
PURE PURE 7.1CH 7.1CH
STANDBY STANDBY DIRECT DIRECT THX THX INPUT INPUT
POWER ON/OFF POWER ON/OFF
PHONES PHONES SETUP MIC SETUP MIC
ENTER
To select TUNER, turn the INPUT SELECTOR knob
on the front panel.
(Using the remote controller)
There are three ways to select TUNER.
1.
2.
1.
Press the HOME button
2.
Press the 4 button.
3.
UP
2.
HDMI
DOWN
VOLUME
BAND T-MODE MEMORY CLEAR
TOP M-DAX DISPLAY
≠
4.
1.
Press the HOME button.
2.
Press the < / > button until 002 is displayed.
3.
Press the 4.TUNER button.
4.
Press the 4.TUNER button.
2.
≠
4.
3.
1.
Press the HOME button.
2.
Press the AMP button.
3.
Press the < / > button until 008 is displayed.
4.
Press the TUNER button.

LISTENING TO THE TUNER

3.
AUTO TUNING
1. 3.
AV PRE TUNER AV8003 AV PRE TUNER AV8003
2. PURE DIRECT PURE DIRECT
M-DAX M-DAX
INPUT INPUT
SELECTOR SELECTOR
1.
SURROUND SURROUND ZONE ZONE
MODE MODE AUTO AUTO ZONE ZONE SPEAKER SPEAKER MENU MENU
PURE PURE 7.1CH 7.1CH
STANDBY STANDBY DIRECT DIRECT THX THX INPUT INPUT
POWER ON/OFF POWER ON/OFF
PHONES PHONES SETUP MIC SETUP MIC
ENTER ENTER
4.
3.
2.
2.
(Using the unit)
1.
Turn the INPUT SELECTOR knob to select
"TUNER".
2.
Press the BAND button to select either FM or
AM.
1.
3. Press the 3 or 4 cursor buttons on the front
Panel for more than 1 second to start the auto
tuning function.
4.
Automatic searching begins then stops when a
station is tuned in.
4.
(Using the remote controller)
1.
Switch the remote controller to TUNER mode.
2.
Press the < / > button until 001 is displayed.
3.
3.
Press the FM or AM button.
4. Press and hold the 3 or 4 cursor button for 1
second or more.
5.
Automatic searching begins then stops when a
station is tuned in.
2.
UP UP
HDMI HDMI
DOWN DOWN
VOLUME VOLUME
EXIT EXIT BAND BAND T-MODE T-MODE MEMORY MEMORY CLEAR CLEAR
TOP TOP M-DAX M-DAX DISPLAY DISPLAY
3.
2.
4.
4.