Names And Function; Front Panel - Marantz AV8003 User Manual

NAMES AND FUNCTION

FRONT PANEL

q w e r t y u i o !0 !1
PURE DIRECT PURE DIRECT
M-DAX M-DAX
INPUT INPUT
SELECTOR SELECTOR
SURROUND SURROUND ZONE ZONE
MODE MODE AUTO AUTO ZONE ZONE SPEAKER SPEAKER
PURE PURE 7.1CH 7.1CH
STANDBY STANDBY DIRECT DIRECT THX THX INPUT INPUT
POWER ON/STANDBY POWER ON/STANDBY
PHONES PHONES SETUP MIC SETUP MIC
@3 @2 @1 @0
q
POWER switch and STANDBY
indicator
When this switch is pressed once, the unit turns ON
and the display illuminates. When pressed again, the
unit turns OFF and the STANDBY indicator will be
illuminated.
w
INPUT SELECTOR knob
(AUDIO/ VIDEO)
This knob is used to select the input sources. (See
page 39)
e
SURROUND MODE button
Press this button to select the surround mode.
r
AUTO (Auto surround) button
Press this button to select the AUTO mode from the
surround modes. When this mode is selected, the
unit determines the surround mode corresponding to
a digital input signal automatically.
!2 !3 ! 4 !5
AV PRE TUNER AV8003 AV PRE TUNER AV8003
UP UP
HDMI HDMI
DOWN DOWN
VOLUME VOLUME
MENU MENU EXIT EXIT BAND BAND T-MODE T-MODE MEMORY MEMORY CLEAR CLEAR
TOP TOP M-DAX M-DAX DISPLAY DISPLAY
ENTER ENTER
!9 !8 !7 !6
t
PURE DIRECT button and indicator
When this button is pressed once, "SOURCE
DIRECT" appears on the FL display. If pressed again,
"PURE DIRECT" appears. After 2 seconds, the FL
display indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.
Notes:
• The surround mode is automatically switched to
AUTO when the pure direct function is turned on.
• Additionally, speaker configurations are fixed
automatically as follows.
Front SPKR = LARGE
Center SPKR = LARGE
Surround SPKR = LARGE
Surround Back SPKR = LARGE
Sub woofer = YES
y
ZONE button
Press this button to activate the Zone system.
"MULTI" indicator will be illuminated in the display.
(See page 66)
u
ZONE SPEAKER button
Press this button to activate the Zone Speaker
system. "MULTI" indicator will be illuminated in the
display. (See page 66)
i
MENU button
Press this button to enter the SETUP MAIN MENU.
o
EXIT button
Press this button to exit from the SETUP MAIN
MENU.
!0
BAND button
Press this button to switch between FM, AM, XM (XM
Ready) and SIRIUS (SIRIUS Ready) in the TUNER
mode.
!1
T-MODE button
Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
The "AUTO" indicator lights in the auto stereo mode.
(See page 49)
!2
INFRARED receiving sensor window
This window receives infrared signals for the remote
controller.
!3
MEMORY button
Press this button to enter the tuner preset memory
numbers or station names. (See page 49)
!4
CLEAR button
Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 50)
!5
VOLUME control knob
This knob is used to adjust the overall sound level.
Turning the control clockwise increases the sound
level.
!6
DISPLAY button
Press this button to change the FL display mode.
!7
M-DAX button
Press this button to select M-DAX processing for
input source. (See page 40)
!8
TOP button
Press this button to return to the top screen of the
main menu when confi guring setup items.
(See page 21)
Also, press this button to return to the top screen of
the network when using the network.
Cursor (5, ∞, 2, 3) / ENTER button
!9
Press these buttons to operate the SETUP MAIN
MENU, NETWORK and TUNER function.
ENGLISH
@0
7.1CH INPUT button
Press this button to select the output of an external
multichannel player.
@1
MIC jack
Automatically measure speaker characteristics using
the included microphone. (See page 27)
@2
THX button
Press this button to select THX processing for input
source.
@3
HEADPHONE jack for stereo headphones
This jack may be used to listen to the unit's output
through a pair of headphones. Be certain that the
headphones have a standard 1/4" stereo phono
plug.
5