Search Mode - Marantz AV8003 User Manual

ENGLISH

SEARCH MODE

You can search for the channel you want to listen to
using one of three search modes. You can also enter
the number directly to select the desired channel.
ALL CHANNEL SEARCH MODE
1.
AV PRE TUNER AV8003 AV PRE TUNER AV8003
UP
PURE DIRECT PURE DIRECT HDMI
M-DAX M-DAX
DOWN
INPUT INPUT
SELECTOR SELECTOR VOLUME
SURROUND SURROUND ZONE ZONE
MODE MODE AUTO AUTO ZONE ZONE SPEAKER SPEAKER MENU MENU EXIT EXIT BAND BAND T-MODE MEMORY CLEAR
PURE PURE 7.1CH 7.1CH
STANDBY DIRECT DIRECT THX THX INPUT INPUT TOP TOP M-DAX DISPLAY
POWER ON/OFF
PHONES PHONES SETUP MIC SETUP MIC
ENTER ENTER
(Using the unit)
1. Press the 3 or 4 cursor button on the front
panel to select the desired station.
(Using the remote controller)
1.
Switch the remote controller to TUNER mode.
2. Press and hold the 3 or 4 cursor button.
62
PRESET SEARCH MODE
1.
AV PRE TUNER AV8003 AV PRE TUNER AV8003
UP
PURE DIRECT RECT HDMI
M-DAX AX
DOWN
INPUT
SELECTOR VOLUME
SURROUND ZONE ZONE
MODE AUTO ZONE ZONE SPEAKER SPEAKER MENU MENU EXIT EXIT BAND BAND T-MODE T-MODE MEMORY CLEAR
PURE 7.1CH 7.1CH
STANDBY DIRECT THX THX INPUT INPUT TOP TOP M-DAX M-DAX DISPLAY
POWER ON/OFF
PHONES SETUP MIC SETUP MIC
ENTER ENTER
2.
(Using the unit)
2.
1. Press the 1 or 2 cursor button on the front
panel to select the desired preset station.
(Using the remote controller)
1.
Switch the remote controller to TUNER mode.
2. 1 or 2 cursor button to tune in the desired
preset station.
Or enter the preset station number with the
numeric buttons.
CATEGORY SEARCH MODE
You can select the desired channel from the category
allocated to each channel.
Category being aired can be only selected.
2.
AV PRE TUNER AV8003 AV PRE TUNER AV8003
UP
PURE DIRECT 3. HDMI
2. M-DAX
DOWN
INPUT
SELECTOR VOLUME
SURROUND ZONE ZONE
MODE AUTO ZONE ZONE SPEAKER SPEAKER MENU MENU EXIT EXIT BAND BAND T-M T-MODE MEMORY CLEAR
PURE 7.1CH 7.1CH
STANDBY THX THX TOP TOP M-DAX DISPLAY
DIRECT INPUT INPUT
POWER ON/OFF
PHONES SETUP MIC SETUP MIC
2.
ENTER ENTER
(Using the unit)
1.
Press the ENTER button on the front panel.
2.
Press the 1 or 2 button on the front panel to
select the desired Category.
3. After selecting the Category, Press the 3 or 4
cursor button to select the desired station of the
category.
4.
You can return to the normal mode by press the
ENTER button during Category Search Mode.
(Using the remote controller)
1.
Switch the remote controller to TUNER mode.
2.
Press the < / > button until 003 is display.
3.
Press the SAT CAT + / − button.
4.
After selecting the category, Press the 3 or 4
cursor button to select the desired station of the
category.
5.
You can return to the normal mode by press the
ENTER button during Category Search Mode.
Note:
• Category search ends automatically about 5 seconds
after the last operation.
CHANNEL DIRECT CALL
You can select the desired channel by directly tapping
the numeric keypads on the remote controller.
2.
3.
2.
3.
4.
5.
4.
1.
Switch the remote controller to TUNER mode.
2.
Press the GUIDE button.
"SR - - -" will appear on the display.
3.
Input the three digit number for your desired
Channel with the numeric keypad on the
remote controller.
4.
The desired channel will automatically be
tuned.
Note:
• If there is no input on the keypad for 5sec., the input
is cancelled to return to the original display
Notes:
• "UPDATING" is displayed while updating channel
map.
• When the selected channel is not available,
"INVALID" is dispIayed.