Marantz AV8003 User Manual page 64

3.
Adjust the antenna location until signal strength
is good.
4. Select channel 0 (SR000) with the 3 or 4
cursor button of the unit or the remote.
4.
AV PRE TUNER AV8003 AV PRE TUNER AV8003
UP
PURE DIRECT PURE DIRECT H H DMI
M-DAX M-DAX
DOWN
INPUT UT
VOLUME
SELECTOR TOR
SURROUND UND ZONE ZONE
MODE DE AUTO AUTO ZONE ZONE SPEAKER SPEAKER MENU MENU EXIT EXIT BAND BAND T-MODE T-MODE MEMORY CLEAR
PURE PURE 7.1CH 7.1CH
THX THX TOP TOP M-DAX M-DAX DISPLAY
STANDBY DIRECT DIRECT INPUT INPUT
POWER ON/OFF
PHONES PHONES SETUP MIC SETUP MIC
ENTER ENTER
• The Radio ID is displayed.
S R O O O S i r i u s I D
Note:
• If "ANTENNA" appears in the front panel display,
the SIRIUS Connect Home tuner, Antenna or AC
adapter may not be connected to the SIRIUS terminal
on the rear panel of this unit properly.
SWITCHING SIRIUS INFORMATION IN THE FRONT
PANEL DISPLAY
You can display SIRIUS information (such as artist
name, song title, composer name, category or signal
status) for the channel currently selected in the front
panel display.
4.
2.
4.
1.
1.
Press the < / > button until 003 is displayed.
2.
Select the information with the SAT DISP
button.
Channel number/name
Artist name/Song title
Composer name
Category
Signal status (satellite)
Signal status (terrestrial)
When the Channel number/name mode is displayed:
S R 0 2 4 :
(If text is more than 13 characters long, the text is
scrolled.)
When the Artist name/Song title is displayed:
N A M E / T I T L E
P i n k F l o i d
F l o i d /
2.
When the Composer name is displayed:
C O M P O S E R
1.
R o g e r W a t e r
The "NAME / TITLE" or "COMPOSER" is displayed
for 2 seconds, followed by the artist name / Song title
or Composer name.
(If artist name / song title or composer name is more
than 13 characters long, the text is scrolled.)
When the channel category is displayed:
C A T : R o c k
Note:
• To change the display content from SIRIUS
information to unit functions, do so from the display
mode. (See "DISPLAY MODE" on page 45)
This SIRIUS information can also be displayed on a
TV monitor connected to the unit.
/
M o n e y
1.
Switch the remote controller to AMP mode.
2.
Press the INFO button. The following
information.
V I D E O
A U D I O
S U R R - M O D E
Z O N E A : O N
Z O N E B : O F F
M A I N
- - - - - - - - - - - - - - - - - - -
3.
When this display appears, press the INFO
button again. SIRIUS information like the
following.
S I R I U S
S I R I U S : 0 0 7
C H A N : 7 0 s
C A T : P o p
N A M E : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
T I T L E : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
C M P O S R : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
S A T : E X C E L L E N T
T E R R : W E A K
4.
Press the INFO button again. The information
display will go out.
Note:
• If the information contains a character that cannot
be recognized by that unit, the character will be
displayed with " "(space).
ENGLISH
2.
3.
4.
: D V D
: S I R I U S
: A U T O
S P K : O F F
S P K : O F F
V O L U M E
I N F O R M A T I O N
H i t s
61