1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. AX691B
  6. Maintenance and service manual

HP AX691B Maintenance And Service Manual

User manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

HP ProLiant DL380 G6 Server

Maintenance and Service Guide
Part Number 495625-401
August 2010 (Tenth Edition)

Advertisement

Table of Contents
loading

Related Manuals for HP AX691B

Summary of Contents for HP AX691B

  • Page 1: Hp Proliant Dl380 G6 Server

    HP ProLiant DL380 G6 Server Maintenance and Service Guide Part Number 495625-401 August 2010 (Tenth Edition)
  • Page 2 © Copyright 2009, 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3: Table Of Contents

    Contents Customer self repair ........................5 Parts only warranty service ..........................5 Illustrated parts catalog ....................... 16 Mechanical components ..........................16 System components ............................ 19 Removal and replacement procedures ................... 25 Required tools ............................25 Preparation procedures ..........................25 Power down the server ........................25 Extend the server from the rack ......................
  • Page 4 Processor..............................54 DIMMs ..............................60 System battery ............................61 System board ............................62 Cabling ............................. 68 SAS hard drive cabling ..........................68 Optical drive cabling ..........................68 BBWC battery cabling ..........................69 Diagnostic tools .......................... 70 Troubleshooting resources ........................... 70 HP ROM-Based Setup Utility ........................

  • Page 5: Customer Self Repair

    Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement.
  • Page 6 Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés. Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation.
  • Page 7 NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono identificate da un "No" nel Catalogo illustrato dei componenti. In base alla disponibilità...
  • Page 8 anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSR- Ersatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen.
  • Page 9 Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de materiales para la sustitución de componentes CSR, HP especificará si los componentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP, deberá...
  • Page 10 bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen. Bij reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde onderdeel en kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
  • Page 11 Serviço de garantia apenas para peças A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os termos do serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar nenhuma taxa.
  • Page 12 Customer self repair 12...
  • Page 13 Customer self repair 13...
  • Page 14 Customer self repair 14...
  • Page 15 Customer self repair 15...

  • Page 16: Illustrated Parts Catalog

    Illustrated parts catalog Mechanical components Item Description Spare part number Customer self repair (on page 5) Access panel 496056-001 Mandatory Power supply cage 496063-001 Mandatory Fan cage 496067-001 Mandatory Optical drive cage 496076-001 Mandatory SFF hard drive cage 496074-001 Mandatory PCI riser cage 496060-001 Mandatory...
  • Page 17 Item Description Spare part number Customer self repair (on page 5) b) Thermal kit (cleaning pad and thermal 468290-001 Optional grease)* c) Processor heatsink kit* 589013-001 Optional Hardware kit* 496058-001 Mandatory a) Optical device blank — — b) Fan blank —...
  • Page 18 No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá...

  • Page 19: System Components

    System components Item Description Spare part number Customer self repair (on page 5) System components Illustrated parts catalog 19...
  • Page 20 Item Description Spare part number Customer self repair (on page 5) Hot-plug fan, 60-mm 496066-001 Mandatory Power supply — — 498152-001 Mandatory a) AC, hot-plug, 1200 W CS High Efficiency power supply b) AC, hot-plug, 750 W power supply* 511778-001 Mandatory c) AC, hot-plug, 460 W power supply* 511777-001...
  • Page 21 Item Description Spare part number Customer self repair (on page 5) d) 2.00-GHz Intel® Xeon® processor E5504* 490074-001 Optional e) 2.13-GHz Intel® Xeon® processor E5506* 506013-001 Optional f) 2.26-GHz Intel® Xeon® processor E5520* 490073-001 Optional g) 2.40-GHz Intel® Xeon® processor E5530* 490072-001 Optional h) 2.53-GHz Intel®...
  • Page 22 Item Description Spare part number Customer self repair (on page 5) a) 72-GB, 15,000-rpm, dual-port 389343-001 Mandatory b) 146-GB, 15,000-rpm, dual-port 488058-001 Mandatory c) 300-GB, 15,000-rpm, dual-port, enterprise 488060-001 Mandatory d) 400-GB, 10,000-rpm, dual-port 456896-001 Mandatory e) 450-GB,15,000-rpm, dual-port 454274-001 Mandatory 461288-001 Mandatory...
  • Page 23 Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service. Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product.
  • Page 24 No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee". Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.

  • Page 25: Removal And Replacement Procedures

    Removal and replacement procedures Required tools You need the following items for some procedures: • T-10/T-15 Torx screwdriver (included with the server) • HP Insight Diagnostics software ("HP Insight Diagnostics" on page 70) Preparation procedures To access some components and perform certain service procedures, you must perform one or more of the following procedures: •...

  • Page 26: Extend The Server From The Rack

    NOTE: If the operating system automatically places the server in Standby mode, omit the next step. Press the Power On/Standby button to place the server in Standby mode. When the server activates Standby power mode, the system power LED changes to amber. IMPORTANT: Pressing the UID button illuminates the blue UID LEDs on the front and rear panels.

  • Page 27: Remove The Server From The Rack

    Remove the server from the rack To remove the server from an HP, Compaq branded, telco, or third-party rack: Power down the server (on page 25). Extend the server from the rack (on page 26). Disconnect the cabling and remove the server from the rack. For more information, refer to the documentation that ships with the rack mounting option.
  • Page 28 Remove the cable arm retainer. Open the cable management arm. Cable management arm with right-hand swing NOTE: To access some components, you may need to remove the cable management arm. To access the product rear panel components, open the cable management arm: Power down the server (on page 25).

  • Page 29: Safety Considerations

    Remove the cable management arm. Safety considerations Before performing service procedures, review all the safety information. Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices.

  • Page 30: Hp Trusted Platform Module

    WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at •...

  • Page 31: Sas Hard Drive Blank

    SAS hard drive blank CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open. Remove the component as indicated.

  • Page 32: Hot-Plug Power Supply

    CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. Access the product rear panel (on page 27). Remove the power supply blank. WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or power supply blank to cool before touching it.

  • Page 33: Optical Drive

    Remove the hot-plug power supply. WARNING: To reduce the risk of electric shock or damage to the equipment, do not connect the power cord to the power supply until the power supply is installed. To replace the component: Slide the hot-plug power supply into the power supply bay. Connect the power cord to the power supply.

  • Page 34: Optical Drive Cage

    Disconnect the cable from the optical drive. Remove the optical drive. To replace the component, reverse the removal procedure. Optical drive cage To remove the component: CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. Power down the server (on page 25).

  • Page 35: Power Supply Backplane

    Disconnect the cable from the optical drive. Remove the optical drive ("Optical drive" on page 33). Remove the optical drive cage. To replace the component, reverse the removal procedure. Power supply backplane To remove the component: Power down the server (on page 25). Remove all power supplies ("Hot-plug power supply"...

  • Page 36: Hot-Plug Fan

    Remove the power supply backplane. To replace the component, reverse the removal procedure. Hot-plug fan The server supports variable fan speeds. The fans operate at minimum speed until a temperature change requires a fan speed increase to cool the server. The server shuts down in the following temperature-related scenarios: •...

  • Page 37: Sff Hard Drive Backplane

    To remove the component: Extend or remove the server from the rack ("Remove the server from the rack" on page 27, "Extend the server from the rack" on page 26). Remove the access panel ("Access panel" on page 30). Remove the fan. CAUTION: Do not operate the server for long periods with the access panel open or removed.

  • Page 38: Sff Hard Drive Cage

    Disconnect all cables from the hard drive backplane. Remove the hard drive backplane. To replace the component, reverse the removal procedure. SFF hard drive cage To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 39: Lff Hard Drive Backplane

    Remove the hard drive backplane ("SFF hard drive backplane" on page 37). Remove the hard drive cage. To replace the component, reverse the removal procedure. LFF hard drive backplane To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 40: Lff Hard Drive Cage

    Remove the hard drive backplane. To replace the component, reverse the removal procedure. LFF hard drive cage To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 41: Pci Riser Cage

    Remove the hard drive cage. To replace the component, reverse the removal procedure. PCI riser cage To remove the component: CAUTION: To prevent damage to the server or expansion boards, power down the server and remove all AC power cords before removing or installing the PCI riser cage. Power down the server (on page 25).

  • Page 42: Air Baffle

    To replace the component, reverse the removal procedure. Air baffle To remove the component: CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open.

  • Page 43: Front Left Bezel

    Disconnect the Systems Insight Display cable. Remove the Systems Insight Display. To replace the component, reverse the removal procedure. Front left bezel To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 44: Front Right Bezel

    Remove the three T-10 Torx screws, and then detach the front bezel. To replace the component, reverse the removal procedure. Front right bezel To remove the component: Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 45: Fan Cage

    Fan cage To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack" on page 27, "Extend the server from the rack" on page 26). Remove the access panel ("Access panel"...

  • Page 46: Expansion Slot Covers

    To replace the component, reverse the removal steps. When re-installing the fans, press down on the top of each fan to be sure it is seated properly. Expansion slot covers CAUTION: To prevent damage to the server or expansion boards, power down the server and remove all AC power cords before removing or installing the PCI riser cage.

  • Page 47: Battery-Backed Write Cache Procedures

    To remove slot covers 2 and 3, lift up on the latch, remove the latch, and then remove the cover. To remove slot covers 5 and 6, push down on the latch, rotate the latch down, and then remove the cover. Battery-backed write cache procedures Two types of procedures are provided for the BBWC option: •...

  • Page 48: Removing The Cache Module

    CAUTION: Do not detach the cable that connects the battery pack to the cache module. Detaching the cable causes any unsaved data in the cache module to be lost. Removing the cache module To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack"...

  • Page 49: Recovering Data From The Battery-Backed Write Cache

    Disconnect the cable, and then remove the battery pack. To replace the component, reverse the removal procedure. Recovering data from the battery-backed write cache If the server fails, use the following procedure to recover data temporarily stored in the BBWC. CAUTION: Before starting this procedure, read the information about protecting against electrostatic discharge...

  • Page 50: Expansion Boards

    Power up the recovery server. A 1759 POST message is displayed, stating that valid data was flushed from the cache. This data is now stored on the drives in the recovery server. You can now transfer the drives (and controller, if one was used) to another server. Expansion boards Half-length expansion board To remove the component:...

  • Page 51: Heatsink

    Remove the expansion board. To replace the component, reverse the removal procedure. Heatsink To remove the heatsink: Power down the server (on page 25). Extend the server from the rack (on page 26). Remove the access panel ("Access panel" on page 30). Remove the PCI riser cage ("PCI riser cage"...
  • Page 52 Remove the heatsink. To replace the heatsink: Clean the old thermal grease from the processor with the alcohol swab. Allow the alcohol to evaporate before continuing. Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution.

  • Page 53: Power Supply Cage Assembly

    Install the heatsink. Close and lock the heatsink retaining latches. Install the air baffle. Install the PCI riser cage. Install the access panel ("Access panel" on page 30). Install the server into the rack. Power up the server. Power supply cage assembly To remove the component: Power down the server (on page 25).

  • Page 54: Processor

    Remove all power supplies ("Hot-plug power supply" on page 32). Remove the server from the rack (on page 27). Remove the access panel ("Access panel" on page 30). Remove the PCI riser cage ("PCI riser cage" on page 41). Remove the air baffle ("Air baffle"...
  • Page 55 Open the heatsink retaining bracket. Remove the heatsink. Removal and replacement procedures 55...
  • Page 56 Open the processor retaining latch and the processor socket retaining bracket. Using your fingers, remove the failed processor. CAUTION: To avoid damage to the system board: Do not touch the processor socket contacts. • Always install the processor socket cover after removing the processor from the socket. •...
  • Page 57 If the processor has separated from the installation tool, carefully re-insert the processor in the tool. Align the processor installation tool with the socket and install the spare processor. CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket.
  • Page 58 Press down firmly until the processor installation tool clicks and separates from the processor, and then remove the processor installation tool. Close the processor retaining latch and the processor socket retaining bracket. Clean the old thermal grease from the heatsink with the alcohol swab. Allow the alcohol to evaporate before continuing.
  • Page 59 Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution. Install the heatsink. Removal and replacement procedures 59...

  • Page 60: Dimms

    Close and lock the heatsink retaining latches. Install the air baffle ("Air baffle" on page 42). Install the PCI riser cage. Install the access panel ("Access panel" on page 30). Install the server into the rack. Power up the server. DIMMs IMPORTANT: This server does not support mixing RDIMMs and UDIMMs.

  • Page 61: System Battery

    Remove the DIMM. To replace the component, reverse the removal procedure. For DIMM configuration information, see the server user guide. System battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock.

  • Page 62: System Board

    Remove the battery. To replace the component, reverse the removal procedure. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider. System board To remove the component: Power down the server (on page 25). Extend or remove the server from the rack ("Remove the server from the rack"...
  • Page 63 Open the processor retaining latch and the processor socket retaining bracket. CAUTION: To avoid damage to the processor: • Handle the processor only by the edges. • Do not touch the bottom of the processor, especially the contact area. Using your fingers, remove the processor from the failed system board. CAUTION: To avoid damage to the system board: Do not touch the processor socket contacts.
  • Page 64 Remove the system board. To replace the component: Install the spare system board. Prepare the processor socket on the spare system board: Open the processor retaining latch and the processor socket retaining bracket. Removal and replacement procedures 64...
  • Page 65 Remove the processor socket protective cover. Install the processor socket cover onto the processor socket of the failed system board. Install the processor on the spare system board. CAUTION: The processor is designed to fit one way into the socket. Use the alignment guides on the processor and socket to properly align the processor with the socket.
  • Page 66 Close the processor retaining latch and the processor socket retaining bracket. Clean the old thermal grease from the heatsink and the top of the processor with the alcohol swab. Allow the alcohol to evaporate before continuing. Apply all the grease to the top of the processor in one of the following patterns to ensure even distribution.
  • Page 67 During the server startup sequence, press the F9 key to access RBSU. Select the System Options menu. Select Serial Number. The following warning is displayed: WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified. This option should only be used by qualified service personnel.

  • Page 68: Cabling

    Cabling SAS hard drive cabling Optical drive cabling Cabling 68...

  • Page 69: Bbwc Battery Cabling

    BBWC battery cabling Cabling 69...

  • Page 70: Diagnostic Tools

    Diagnostic tools Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance on ProLiant servers and server blades. This guide includes problem- specific flowcharts to help you navigate complex troubleshooting processes.

  • Page 71: Hp Insight Diagnostics Survey Functionality

    HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and other related data needed for effective server management. Available in Microsoft® Windows® and Linux versions, the utility helps to ensure proper system operation. For more information or to download the utility, refer to the HP website (http://www.hp.com/servers/diags).

  • Page 72: Hp Insight Remote Support Software

    HP Insight Remote Support software HP strongly recommends that you install HP Insight Remote Support software to complete the installation or upgrade of your product and to enable enhanced delivery of your HP Warranty, HP Care Pack Service or HP contractual support agreement. HP Insight Remote Support supplements your monitoring, 24 x 7 to ensure maximum system availability by providing intelligent event diagnosis, and automatic, secure submission of hardware event notifications to HP, which will initiate a fast and accurate resolution, based on your product’s service level.

  • Page 73: Internal Sd Support

    For additional security, external USB functionality can be disabled through RBSU. Disabling external USB support in RBSU disables the USB connectors on the local I/O cable. Internal USB functionality is unaffected. Internal SD support An internal SD connector is available for use with embedded Hypervisors. This solution provides for use of a permanently installed SD card in the internal connector, decreasing the possibility of tampering or loss.

  • Page 74: Component Identification

    Component identification Front panel components • SFF model Item Description Quick release levers (2) Systems Insight Display Hard drive bays SATA optical drive bay Video connector USB connectors (2) • SFF model with optional hard drive cage Item Description Quick release levers (2) Systems Insight Display Hard drive bays Hard drive bays (optional)

  • Page 75: Front Panel Leds And Buttons

    Item Description Video connector USB connectors (2) • LFF model Item Description Quick release levers (2) Systems Insight Display Hard drive bays USB connectors (2) Video connector Front panel LEDs and buttons Item Description Status UID LED and button Blue = Activated Flashing blue = System being remotely managed Off = Deactivated Component identification 75...

  • Page 76: Systems Insight Display Leds

    Item Description Status System health LED Green = Normal Amber = System degraded. Red = System critical. To identify components in degraded or critical state, see "Systems Insight Display LEDs (on page 76)." Power On/Standby button Green = System on and system power LED Amber = System in standby, but power is still applied Off = Power cord not attached or power supply failure...

  • Page 77: Systems Insight Display Led Combinations

    Item Description Status NIC link/activity LED Green = Network link Flashing green = Network link and activity Off = No link to network. If the power is off, view the rear panel RJ-45 LEDs for status ("Rear panel LEDs and buttons"...

  • Page 78: Rear Panel Components

    Health LED Status Systems Insight System power Display LED and color Fan (amber) Green Two or more fans have failed or been removed. Power supply (amber) Amber • Only one power supply is installed and that power supply is in standby. •...

  • Page 79: Rear Panel Leds And Buttons

    PCI slot 1 Power supply bay 2 Power supply bay 1 (populated) USB connectors (2) Video connector NIC 1 connector NIC 2 connector Mouse connector Keyboard connector Serial connector iLO 2 connector NIC 3 connector NIC 4 connector Rear panel LEDs and buttons Item Description Status...

  • Page 80: Non-Hot-Plug Pci Riser Board Slot Definitions

    Non-hot-plug PCI riser board slot definitions Primary Secondary PCIe riser PCIe x16 riser PCIe/PCI-X riser slot description slot description slot description (slot - form factor) (slot - form factor) 1 - FL/FH 4 - FL/FH PCIe x16 PCIe x16 PCI-X 64-bit/133- (8,4,1) (16,8,4,1) 2 - HL/FH...

  • Page 81: System Board

    System board System board components Item Description Processor 2 DIMM slots SAS power connector A SAS power connector B Front I/O connector SATA optical drive connector Internal USB connector System battery Power supply backplane connector NMI jumper System maintenance switch Processor socket 2 Primary riser connector SD card slot...

  • Page 82: System Maintenance Switch

    Item Description Processor 1 DIMM slots Secondary riser connector SAS connector A SAS connector B Cache module connector Fan connector 1 Fan connector 2 Fan connector 3 Fan connector 4 Fan connector 5 Fan connector 6 System maintenance switch Position Default Function Off = iLO 2 security is enabled.

  • Page 83: Nmi Functionality

    NMI functionality An NMI crash dump enables administrators to create crash dump files when a system is hung and not responding to traditional debug mechanisms. Crash dump log analysis is an essential part of diagnosing reliability problems, such as hangs in operating systems, device drivers, and applications.

  • Page 84: Dimm Identification

    DIMM identification IMPORTANT: This server does not support mixing RDIMMs and UDIMMs. Attempting to mix these two types causes the server to halt during BIOS initialization. The memory subsystem may be populated with either RDIMMs or UDIMMs, but mixing the two types is not supported.

  • Page 85: Sas And Sata Device Numbers

    SAS and SATA device numbers • SFF device bay numbering • Optional SFF device bay numbering • LFF device bay numbering Component identification 85...

  • Page 86: Sas And Sata Hard Drive Leds

    SAS and SATA hard drive LEDs Item Description Fault/UID LED (amber/blue) Online LED (green) SAS and SATA hard drive LED combinations Online/activity Fault/UID LED Interpretation LED (green) (amber/blue) On, off, or Alternating amber The drive has failed, or a predictive failure alert has been flashing and blue received for this drive;...

  • Page 87: Pci Riser Cage Leds

    Interpretation Online/activity Fault/UID LED LED (green) (amber/blue) Flashing The drive is active, and it is operating normally. irregularly Steadily amber A critical fault condition has been identified for this drive, and the controller has placed it offline. Replace the drive as soon as possible.

  • Page 88: Battery Pack Leds

    Battery pack LEDs Item ID Color Description Green System Power LED. This LED glows steadily when the system is powered up and 12 V system power is available. This power supply is used to maintain the battery charge and provide supplementary power to the cache microcontroller.

  • Page 89: Hot-Plug Fans (6-Fan Configuration)

    LED3 pattern LED4 pattern Interpretation — One blink per The battery pack is below the minimum charge level and is being second charged. Features that require a battery (such as write cache, capacity expansion, stripe size migration, and RAID migration) are temporarily unavailable until charging is complete.

  • Page 90: Specifications

    Specifications Environmental specifications Specification Value Temperature range* Operating 10°C to 35°C (50°F to 95°F) Shipping -30°C to 50°C (-22°F to 122°F) Storage -30°C to 60°C (-22°F to 140°F) Maximum wet bulb 28°C (82.4°F) temperature Relative humidity (noncondensing)** Operating 10% to 90% Non-operating 5% to 95% * All temperature ratings shown are for sea level.
  • Page 91 Rated steady-state power 800 W at 100V AC input 900 W at 120V AC input 1200 W at 200V to 240V AC input Maximum peak power 800 W at 100V AC input 900 W at 120V AC input 1200 W at 200V to 240V AC input •...

  • Page 92: Hot-Plug Power Supply Calculations

    Rated steady-state power 460 W at 100V to 120V AC input 460 W at 200V to 240V AC input Maximum peak power 460 W at 100V to 120V AC input 460 W at 200V to 240V AC input Hot-plug power supply calculations For hot-plug power supply specifications and calculators to determine electrical and heat loading for the server, refer to the HP Enterprise Configurator website (http://h30099.www3.hp.com/configurator/).

  • Page 93: Acronyms And Abbreviations

    Acronyms and abbreviations Automatic Server Recovery BBWC battery-backed write cache double data rate DIMM dual inline memory module Integrated Lights-Out Integrated Management Log non-maskable interrupt NVRAM non-volatile memory PCIe peripheral component interconnect express PCI-X peripheral component interconnect extended POST Power-On Self Test RBSU ROM-Based Setup Utility Acronyms and abbreviations 93...
  • Page 94 serial attached SCSI SATA serial ATA trusted platform module unit identification universal serial bus Acronyms and abbreviations 94...

  • Page 95: Index

    Index expansion boards 50 expansion slot covers 46 expansion slot covers, removing 46 access panel 30 extending server from rack 26 ADU (Array Diagnostic Utility) 71 air baffle 42 Array Diagnostic Utility (ADU) 71 fans 36, 89 features 74 front panel buttons 75 battery 83 front panel components 74 battery cabling for BBWC 69...
  • Page 96 specifications, environmental 90 specifications, server 92 management tools 70 static electricity 29 mechanical components 16 status lights, battery pack 88 memory dump 83 switches 83 mouse connector 78 system battery 61 system board 62, 81 system board components 81 system components 74 NIC connectors 78 system maintenance switch 82, 83 NMI jumper 83...

This manual is also suitable for:

Proliant dl380 g6

Table of Contents