Related Manuals for Merck Millipore Millistak+ P0D
Summary of Contents for Merck Millipore Millistak+ P0D
- Page 1 User Guide Millistak+ P0D Holders ® Process Scale and Expansion KIT The life science business of Merck KGaA, Darmstadt, Germany operates as MilliporeSigma in the U.S. and Canada.
-
Page 2: Table Of Contents
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Contents Catalog Numbers ............3 Millistak+ P0D Holder Process Scale ......4 ® Installation ..............5 Installing the Holder Process Scale ........5 Installing the Expansion KIT .........5 Installing the Millistak+ P0D Filter .......5 ®... -
Page 3: Catalog Numbers
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Catalog Numbers This user guide includes instructions for the following catalog numbers: Catalog Number Description Primary Use Quantity per Package Process Scale Holders MP0DSYS1A Process Scale 1-rack, Gemü valves 5 to 10 devices ®... -
Page 4: Millistak+ ® P0D Holder Process Scale
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Millistak+ P0D Holder Process ® Scale Description Leveling Pad Cap Caster Alignment Rod Clamp Rod Moveable Endplate Tri-Clover Clamp Clamp Insert Inlet Fitting Port Vent Fitting Port Outlet Fitting Port Fixed Plate Hydraulic Cylinder Hydraulic Pressure Gauge... -
Page 5: Installation
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Installation Install disposable fittings into the fixed plate (11). Install at least five 1 m pods into the rack, as described in the Pod Filter Installation section of this manual. Once the Installing the Holder Process Scale pods are installed and the hydraulic system is energized, attach the manifolds to the disposable fittings. - Page 6 Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Position the pods so that the alignment key of the pod 17. Once approximately 1000 psi (69 bar) is achieved on faces the fixed plate (11) of the holder. If the pods are the gauge, close the hydraulic valve.
-
Page 7: Operation
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Operation Millistak+ P0D Filter ® Disassembly Refer to the user guide (document number: P88724) supplied with the pod filters for operating parameters and instructions. On multi-rack systems, this process should be performed on each rack, from highest to lowest. -
Page 8: Manifold Cleaning (Cip)
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Manifold Cleaning (CIP) Hydraulic System Maintenance For each rack, connect the feed and filtrate manifolds using the symmetric CIP spools provided (MP0DCIPSPLH and MP0DCIPSPLV). Hydraulic Fluid Replacement Remove the pressure gauge at the top of the feed and Relieve the pressure in the hydraulic system by opening filtrate manifolds and connect them with the asymmetric the hydraulic valve and hydraulic pump relief valve. -
Page 9: Hydraulic Gauge Replacement
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Hydraulic Gauge Replacement Hydraulic Pump Replacement Relieve the pressure in the hydraulic system by opening Relieve the pressure in the hydraulic system by opening the hydraulic valve and hydraulic pump relief valve. the hydraulic valve and hydraulic pump relief valve. -
Page 10: Bleeding The System
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Bleeding the System Testing the System Turn the hydraulic pump vent valve to the VENT position. With no Millistak+ P0D filters in place, adjust clamp rods ® so that the clamp inserts are snug against the hydraulic Adjust the clamp rods to allow the hydraulic cylinder cylinder pistons. -
Page 11: Hydraulic Gauge Calibration Using The Quick Connector
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Hydraulic Gauge Calibration using the Quick Open the hydraulic pump release valve and the hydraulic valve to Connector release the pressure. Check the hydraulic pressure gauge (13) indicates 0 psi. Check the pump vent valve is on Vent position. -
Page 12: P&D - Millistak+ P0D Holder Process Scale
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® P&D - Millistak+ P0D Holder Process Scale ®... -
Page 13: Spare Parts And Accessories
Millistak+ P0D Holders Process Scale and Expansion KIT User Guide ® Spare Parts and Accessories Catalog Number Description Quantity per Package MP0DHYPUMP Hydraulic pump MP0DHFLUID Hydraulic fluid (1 Liter) MP0DHYGAGE Hydraulic system pressure gauge (for design without quick connector) MP0DINSERT Clamp insert 1.5 in. - Page 14 Millipore, Millistak and the Vibrant M are trademarks of Merck KGaA, Darmstadt, Germany or its affiliates. All other trademarks are the property of their respective owners. Detailed information on trademarks is available via publicly accessible resources. © 2022 Merck KGaA, Darmstadt, Germany and/or its affiliates.
Need help?
Do you have a question about the Millipore Millistak+ P0D and is the answer not in the manual?
Questions and answers