Related Manuals for RightAngle Delta View Single Unit
Summary of Contents for RightAngle Delta View Single Unit
- Page 1 Delta View - Single Unit Assembly Instructions Warranty: raproducts.com/resources/warranty Instruction #54595 • Dated: 07/07/2023 1 of 16...
-
Page 2: Basic Safety Instructions
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT. USE THIS PRODUCT ONLY AS INSTRUCTED. FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY. WARNING Basic Safety Instructions Intended Use. This Product is exclusively designed for use as indoor office furniture in compliance with all instructions and safety warnings in the user manual. -
Page 3: Tools Required For Assembly
Tools Required for Assembly Power Driver with Adjustable Torque #2 Phillips Head Driver Bit #2 Square Head Drive Bit (Recommended) Phillips Screwdriver Hardware Included for Assembly (may have extra) 5/8” Washer Head Wood Screw x16 Slim Fix Bolt x14 M6 x 30mm Machine Screw x6 Gas Strut Bracket Screw x5 Hinge Screw x8 M6 x 50mm Machine Screw x4... - Page 4 Parts Continued Left Side Panel x1 Right Side Panel x1 Back Panel x1 Kick Panel x1 Front Worksurface x1 Back Worksurface x1 Shown here with cams facing upwards Shown here with cams facing upwards Shown here with cams facing upwards K&A Manufacturing •...
- Page 5 Step 1 (Assembly A & B) • Lay the left leg (X) on a flat surface with the side with the holes facing up. • Place the left side panel (AA) on top of the left leg with the cams facing up. •...
- Page 6 Step 2 • Lay the back panel (CC) on a flat surface with pilot holes facing upwards. • Align the bottom holes on the column assembly (Y) with the pre-drilled holes and attach with washer head wood screws (E). Do NOT tighten. •...
- Page 7 Step 3 • Align the keyboard nests (R) with the pre- drilled holes and attach it with three washer head wood screws (E). • Align the mouse nests (S) with the pre- drilled holes and attach it with two washer head wood screws (E).
- Page 8 Step 4 • Align the bottom part of the hinge mounting bracket (M) with the pre-drilled holes at the top of the back pannel (CC). • Attach hinge (M) with the hinge screws provided in the package (I). Do NOT fully tighten.
- Page 9 Step 5 (Assembly C) • On the back panel (CC), insert six slim fix bolts (F) into the pre-drilled holes. • Set assembly off to the side. This will be Assembly C. K&A Manufacturing • 800.298.4351 9 of 16...
- Page 10 Step 6 (Assembly D) • Lay the kick panel (DD) on a flat surface with cams facing upwards. • Align the wire managements (T) with the pre-drilled holes. • Attach to kick pannel with three washer head wood screws (E). •...
- Page 11 Step 7 (Assembly E) • Lay the front worksurface (EE) on a flat surface with the pilot holes holes facing up. • Insert two Slim Fix Bolts (F) into the pre- drilled holes. • Set off to the side. This will be Assembly E. Step 8 (Assembly F) •...
- Page 12 Step 9 • Take Assembly A and make sure all the cams are open with a Philips screwdriver. • Carefully insert the Slim Fix Bolts from Assembly C into the cams of Assembly A. • Lock the cams using Philips screwdriver. •...
- Page 13 Step 11 • Take Assembly E and carefully insert the Slim Fix Bolts (on the underside of Assembly E) into the cams on Assembly D. • Lock the cams. • Insert four 50mm machine screws (J) through the legs into the work surface and fully tighten.
- Page 14 Step 13 • Snap the tube end of the gas strut into the ball of the top gas strut mounting bracket Snap together (P). • Attach two rubber bumpers (K) to the top corners of the underside of Assembly F. Step 14 •...
- Page 15 Step 15 • Put the column assembly in a raised position Push here Push down on the column assembly until you hear a click and then remove hand to let it rise. Step 16 • Slide the monitor and monitor bracket assembly onto the column assembly.
- Page 16 Step 17 • Insert the grommets (U) into the panels. • Insert the access door assembly (V) and close the latch. K&A Manufacturing • 800.298.4351 16 of 16...
Need help?
Do you have a question about the Delta View Single Unit and is the answer not in the manual?
Questions and answers