Related Manuals for RightAngle Delta View Dual Unit
Summary of Contents for RightAngle Delta View Dual Unit
- Page 1 Delta View - Dual Unit Assembly Instructions Warranty: raproducts.com/resources/warranty Instruction #54596 • Dated: 07/07/2023 1 of 12...
-
Page 2: Basic Safety Instructions
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT. USE THIS PRODUCT ONLY AS INSTRUCTED. FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY. WARNING Basic Safety Instructions Intended Use. This Product is exclusively designed for use as indoor office furniture in compliance with all instructions and safety warnings in the user manual. -
Page 3: Tools Required For Assembly
Tools Required for Assembly Power Driver with Adjustable Torque #2 Phillips Head Driver Bit #2 Square Head Drive Bit (Recommended) Phillips Screwdriver Hardware Included for Assembly (may have extra) 5/8” Washer Head Wood Screw x32 Cam Bolt x24 M6 x 30mm Machine Screw x6 Gas Strut Bracket Screw x10 Hinge Screw x16 M6 x 50mm Machine Screw x4... - Page 4 Step 1 (Assembly A & B) • Lay the left leg (X) on a flat surface with the side with the holes facing up. • Place the left side panel on top of the left leg with the cams facing up. •...
- Page 5 Step 3 • Align the keyboard nests (R) with the pre- drilled holes and attach it with the washer head wood screws (E). • Align the mouse nests (S) with the pre- drilled holes and attach it with the washer head wood screws (E).
- Page 6 Step 5 (Assembly C) • Insert the Slim Fix Bolts (F) into the pre- drilled holes. • Then set the assembly off to the side. • This will be ”Assembly C” Step 6 (Assembly D) • Lay the kick panel on a flat surface. •...
- Page 7 Step 7 (Assembly E) • Lay the worksurface access door on a flat surface with the holes facing up. • Insert the Slim Fix Bolts (F) into the predrilled holes. • Set off to the side. • This will be “Assembly E” Step 8 (Assembly F) •...
- Page 8 Step 9 • Take Assembly “A” and make sure all the cams are open with a Philips screwdriver. • Carefully insert the Slim Fix Bolts from “Assembly C” into the cams of “Assembly A”. • Lock the cams. • Then do the same thing with “Assembly B” Closed = Clockwise Open = Counter-Clockwise Step 10...
- Page 9 Step 11 • With the help of another person, tip the desk back some to install the bottom reinforcement panel. • Lock the cams. • Install the top reinforcement panel. • Lock the cams. Step 12 • Take “Assembly F” and carefully insert the Slim Fix Bolts into the cams on “Assembly D”.
- Page 10 Step 13 • Take “Assembly E” and slide the top part of the hinge into the bottom part of the hinge. • Tighten screws for the hinge brackets. Step 14 • Snap the tube end of the gas strut into the ball of the top gas strut mounting bracket (P).
- Page 11 Step 15 • Place the monitors face down on a flat surface. • Line the holes on the monitor bracket (Z) with the holes on the monitor match “top” sticker with top of monitor. • Install (L) the screws and fasten them down tight.
- Page 12 Step 17 • Slide the monitor and motor bracket assembly onto the Column Assembly. Step 18 • Insert the grommets (U) into the panels. • Insert the access door assembly (V) and close the latch. You may need to press in the grommets in place or may have to tap them gently with a rubber mallet.
Need help?
Do you have a question about the Delta View Dual Unit and is the answer not in the manual?
Questions and answers