Advertisement
Advertisement
Table of Contents
Related Manuals for Link LK-EXP18L
Summary of Contents for Link LK-EXP18L
- Page 1 LINK INSTALLATION MANUAL LK-EXP18L FORD EXPEDITION 2018 & UP DRIVER SIDE FRONT...
- Page 2 Air Bag Kit Electric Seat -Left- LK-F150C15-12 Kit Fuse for Forward/Back Motor EW-CK-00 12V Power Supply Wiring Kit LK-UNI-650 Manual Backup Tool Kit PART NUMBER LK-EXP18L DESCRIPTION LINK Ford Expedition 2018 & Up -Left- 1 of 4 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 3 Pivot Cover -Left- Black DETAIL A SCALE 1:1 Drill: 5/16'' 1.-Drill Ø5/16 (2 layers deep) 2.-Drill 3/16'' 3.-Thread 1/4-20 UNC Drill 3/16'' Thread: 1/4-20 UNC PART NUMBER LK-EXP18L DESCRIPTION LINK Ford Expedition 2018 & Up -Left- 2 of 4 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 4 Socket Head Cap Screw Zinc Plated 3/8-16 x 1 1/4 LK720LB Pivot Motor Cover -Left- Black LK710B Chain Covert -Black- PRD 110-106 Round washer head tapping screw #8 x 3/4 PART NUMBER LK-EXP18L DESCRIPTION LINK Ford Expedition 2018 & Up -Left- 3 of 4 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 5 Intside Cover -Left- Black PRD 251-177 Trim Panel Clip Ø1/4'' x 3/4'' Black LK700B Link Covert -Black- LK-EXP18LB-07 Seat Trim -Left- Black DETAIL FOR L-LK912 PART NUMBER LK-EXP18L DESCRIPTION LINK Ford Expedition 2018 & Up -Left- 4 of 4 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 6 We have prepared quick, easy and to the point tutorial videos imbedded into the software. Take a moment and watch the video that shows all the features of the tablet. To do this, open the LINK IT app and tap on ‘INFO’.
-
Page 7: Before Starting The Installation
Make sure the steering wheel adjustment is fully UP and IN to allow maximum clearance for the driver seat. When installing the LINK with hand controls, hand controls should be installed after the LINK. Remove the driver side OEM seat and place on a workbench to be able to remove all the plastic trims, also remove the seat belt receiver. - Page 8 2. Remove the wiring harness and control box from the seat base. 3. Remove the seat cushion. LINK Ford Expedition 2018 & UP driver side-p.4...
- Page 9 5. Unclip the seat cushion support and fan, pass it out through the back of the seat, along with the seat thigh adjustment pad (if present). 6. Remove the seat back, keep the OEM bolts for reinstallation. LINK Ford Expedition 2018 & UP driver side-p.5...
- Page 10 7. Remove the left hand seat trim support, keep for re-installation. Remove the seat pan, and also remove the seat control box bracket, located on the underside of the seat pan. LINK Ford Expedition 2018 & UP driver side-p.6...
- Page 11 10. Run the power from the battery to the LINK. To do this, thread the red power cable (+) under the doorstep molding and through the firewall. Make sure you pass through a grommet in the firewall to prevent the cable from chaffing.
- Page 12 The wiring extension will be routed out of the bottom right hand corner of the seat. The control box will have to be relocated to the floor under the seat. WIRING BEFORE EXTENTION LINK Ford Expedition 2018 & UP driver side-p.8...
- Page 13 13. Position the extended floor connector and control box on the floor before installing the floor adapter The LINK floor adapter to avoid having to unbolt the adapter to pass the connectors at a later stag LINK Ford Expedition 2018 & UP driver side-p.9...
- Page 14 OEM bolts. 14. The b pillar trim will have to be cut and modified with the provided stencil to allow clearance for the LINK. To remove the trim you will also have to unbolt the seat belt. Modify as per the photos and then re-install.
- Page 15 LINK Ford Expedition 2018 & UP driver side-p.11...
- Page 16 LINK. You may want to use 17. Place the provided shims a little grease or silicone to hold them in place. Or, install the LINK and slide them into place after. LINK Ford Expedition 2018 & UP driver side-p.12...
- Page 17 18. Place the LINK in the vehicle on the floor adapters. Use the four longer (3/8’’-16 x 1¼’’) socket cap bolts to secure the LINK by the pivot, and use the four shorter (3/8’’-16 x 7/8’’) bolts to secure the interior of the LINK.
- Page 18 Be sure to attach the unused motor wires in the seat. The seat back can now be reinstalled onto the LINK along with the seat cushion support, and thigh adjustment pad. Pay specific attention to firmly fastening the harness where it exits the seat back.
- Page 19 22. Reinstall the seat belt receiver using the OEM bolt, and reconnect it to the wiring harness. 23. Reconnect the seat back, and seat fan. Attach all the wires with zip ties. LINK Ford Expedition 2018 & UP driver side-p.15...
- Page 20 24. Before reinstalling the seat cushion, cut a slot in the middle of the fabric flab at the back of the cushion. Attach the fabric flap under the seat. NOTE: make it fit snugly under the seat base to ensure it does not get caught in the mechanism of the LINK. LINK Ford Expedition 2018 & UP driver side-p.16...
- Page 21 26. Install the left hand seat trim support onto the seat adapter using the provided self tapping screws. LINK Ford Expedition 2018 & UP driver side-p.17...
- Page 22 28. The left hand side plastic trim will have to be cut modified before reinstallation to allow clearance at the pivot of the LINK. The replacement trim # LK-EXP18LB-07 will have to be installed onto it, using the provided trim clips.
- Page 23 29. Remove the part indicated to allow clearance on the seat adapter. 30. Reconnect and reinstall the seat trim. LINK Ford Expedition 2018 & UP driver side-p.19...
- Page 24 31. Attach the extended wiring harness at the back of the seat and at the b pillar, leaving just enough wire to follow the seat in and out. LINK Ford Expedition 2018 & UP driver side-p.20...
- Page 25 LINK be exactly at the ‘HOME’ position before moving on to the next step. If the LINK is slightly off its ‘HOME’ position or the starting point of its movements, there is a strong chance that the LINK will not fit through the doorway properly and/or will cause problems with the preset of the LINK.
- Page 26 34. Now that the LINK is in its ‘HOME’ position, RESET the unit by pressing ‘CONFIRM RESET’. A screen will pop up to ask: ‘ARE YOU SURE YOU WANT TO RESET ZERO POSITION’. Press ‘ACCEPT’. The LINK will emit two (2) audible beeps to confirm ‘RESET’, and will now be in reduced power mode. In pendant mode, run one full cycle to exit reduced power mode.
- Page 27 9 Vo lt Ba tte ry T he LINK is designed to run off of the vehicle’s 12 vo lt b a tte ry. It is e q uip p e d with ma ny sa fe g ua rd s to e nsure tha t the c o ntro lle r b o x a lwa ys re ta ins its p ro g ra ming se q ue nc e .
-
Page 28: Normal Use
All systems functional and ready to go. Power Reduce Mode To exit, simply run the LINK a full cycle. Major Problem Do not use the LINK - contact your Mobility Equipment Dealer No Response No 12V Power DIAG NO ST IC MO DE (Press and hold the power button) Current vehicle 12V power supply level. -
Page 29: Year Limited Warranty
( LINK ) inste a d o f re p a iring o r re p la c ing the o rig ina l e q uip me nt. - Page 30 LINK Ford Expedition 2018 & UP driver side-p.26...
Need help?
Do you have a question about the LK-EXP18L and is the answer not in the manual?
Questions and answers