Related Manuals for Link LK-SILX07R
Summary of Contents for Link LK-SILX07R
- Page 1 LINK INSTALLATION MANUAL LK-SILX07R Chevrolet Silverado; GMC Sierra-Extended Cab 2007-2013 Front Right LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 1...
- Page 2 We have prepared quick, easy and to the point tutorial videos imbedded into the software. Take a moment and watch the video that shows all the features of the tablet. To do this, open the LINK IT app and tap on ‘INFO’.
- Page 3 KIT LINK CHEVROLET SILVERADO EXTENDED CAB 2007 - 2013 ITEM PART NUMBER C/Quantité DESCRIPTION LK000R-02 Long Model LINK -Right- LK-UNI-305R 305 Top Bearing Plate -Right- PRD 337-213P Button head socket cap screw Zinc Plated 5/16-18 x 3/4 PRD 192-141 Spring Tensions Pin 3/16 x 3/4...
- Page 4 KIT LINK CHEVROLET SILVERADO EXTENDED CAB 2007 - 2013 ITEM PART NUMBER 1/Quantité DESCRIPTION LK000R-02 Long Model LINK -Right- LK-UNI-305R 305 Top Bearing Plate -Right- PRD 337-213P Button head socket cap screw Zinc Plated 5/16-18 x 3/4 PRD 192-141 Spring Tensions Pin 3/16 x 3/4...
- Page 5 KIT LINK CHEVROLET SILVERADO EXTENDED CAB 2007 - 2013 ITEM PART NUMBER 2/Quantité DESCRIPTION LK-SILC07R-03 Seat Adapter -Right- PRD 339-136P Socket Shoulder Screw Zinc Plated 3/8 x 1/2 x 5/16-18 THD PRD 333-107 Nylon Insert Locknut 5/16-18 LK710B Chain Covert -Black-...
- Page 6 KIT LINK CHEVROLET SILVERADO EXTENDED CAB 2007 - 2013 ITEM PART NUMBER 3/Quantité DESCRIPTION LK720RB Pivot Motor Cover -Right- Black LK960 LINK Wired Control LK-SILC07R-01 Floor Adapter -Right- LK-SILC07RB-05 Floor Cover -Right- Black LK-SILC07R-06 Air Bag Box Support LK-SILX07R-07 Tape Drive Support -Right-...
- Page 7 The seat belt tensioner will be relocated to the provided bracket on the LINK. Use the provided plastic trim LK-SILX07RB-08 to replace the hole left by the removal of the plastic housing.
- Page 8 Prepare the seat. Remove the plastic shrouds from both sides of the seat. Disconnect seat control module. Remove the seat belt receiver. And seatbelt position sensor connector. LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 4...
- Page 9 4. Remove the seat back to give access to the seat back wiring. 5. Remove the lower seat back plastic shroud, and the wiring harness from the seat back. LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 5...
- Page 10 6. The seat bottom floor frame, wiring harness, and foam base will have to be removed. LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 6...
- Page 11 7. Once the seat bottom floor frame is removed, the seat wiring harness will have to be completely removed to be modified and extended to allow for the movement of the LINK and keep the OEM functions. 8. Parts of the wiring harness will have to be carefully skinned away to give access to the wires to be extended and modified.
- Page 12 LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 8...
- Page 13 LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 9...
- Page 14 9. The main harness connector will now have to extended with the 18 gauge cable and connectors provided in the kit. Cut and extend the wires on the main seat connector. « LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 10...
- Page 15 11. The wiring harness can now be re-installed on the seat. Attach the wire harness using the provided zip ties. 12. Install the airbag seat position sensor on the provided bracket LK-SILC07R-04. And attach it in the seat back. LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 11...
- Page 16 13. Run the power and ground for the LINK. Follow the instructions as detailed in the attached document: ELECTRICAL INSTALLATION. (Found at the end of this manual). 14. On the floor of the vehicle, the airbag control module, the crash sensor, and the heating duct will have to modified and repositioned, to allow the installation of the LINK floor adaptors.
- Page 17 16. Reposition the airbag control module and cut off one of the old retaining bolts. 17. Install the LINK floor adaptor LK-SILX07R-01 on the supplied rear shims LK-SILX07-10 and tighten down with original OEM bolts on the front and the supplied M12-1.75X50mm bolts at the back.
- Page 18 19. Remove the LINK from the shipping box and set it on a table or work bench. The LINK has been pre-programmed to fit in the application it was ordered for. *IMPORTANT: Before connecting auxiliary 12V power to the LINK, connect the 9V battery. The 9V battery will maintain memory of the movements of the motors for approximately 12 hours, in event of 12V power loss.
- Page 19 21. Place the LINK in the vehicle on the floor adapter. Use the four (4) 3/8’’-16 x 1¼’’ socket cap bolts to secure the LINK by the pivot, and use the four (4) 3/8’’-16 x 7/8’’ to secure the interior of the LINK.
- Page 20 24. The seat can be ‘TILTED’ up in ‘BYPASS’ mode to help with the reinstallation of the seat base. 25. Now finish reinstalling the seatback wiring and pose the seat back. 26. The lower seat back plastic trim will have to be modified. LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 16...
- Page 21 28. The right hand side plastic shroud will have to be modified to clear the pivot before reinstallation. LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 17...
- Page 22 29. Reinstall the plastic shroud, the electric seat control connectors and seat belt. 30. Install the seat belt tensioner to the underside of pivot block at the back of the LINK, remove the 2 original allen screws and replace with the provided 5/15XG8 bolts, and then install the provided fabric cover LK-SILX07B-09.
- Page 23 33. Using the LINK IT app, use ‘RESET’ mode to bring the seat to the ‘HOME’ position. PLEASE WATCH THE SHORT TUTORIAL THAT APPEARS WHEN YOU TOUCH ‘RESET’ TO UNDERSTAND HOW THIS FEATURE WORKS.
- Page 24 ZERO POSITION’. Press ‘ACCEPT’ and the LINK will emit two (2) audible beeps to confirm ‘RESET’. The LINK is now set to its ‘HOME’ position. NOTE: This is the position that the LINK will start its outward travel from. If the LINK is adjusted forward and/or tilted up with the seat adjustment buttons found on the hand pendant, pressing ‘OUT’...
- Page 25 9 Volt Battery The LINK is designed to run off of the vehicle’s 12 volt battery. It is equipped with many safeguards to ensure that the controller box always retains its programing sequence. One of those safeguards is the 9 volt memory backup battery.
- Page 26 (NOTE: It is preferable to locate it in a spot where the sheet metal is doubled-up to insure a better ground.) LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 22...
-
Page 27: Normal Use
Diagnostic Mode will loop or cycle as long as you hold the power button. Once you see 2 times, the diagnostics are looping – and therefore are back at the beginning (i.e.: reading vehicle 12V power supply level.) LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 23... -
Page 28: Year Limited Warranty
ADAPT-SOLUTIONS #1 LTD. 3 YEAR LIMITED WARRANTY Adapt-Solutions # 1 Ltd. (Adapt Solutions), warrants to the original purchaser of a LINK that the equipment is free from defects in material and workmanship for a period of three years from date of purchase. - Page 29 LINk 2007 - 2013 Chevrolet Silverado; / GMC Sierra Extended Cab; Front Right p. 25...
Need help?
Do you have a question about the LK-SILX07R and is the answer not in the manual?
Questions and answers