Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Link LK-WRG18L
Summary of Contents for Link LK-WRG18L
- Page 1 LINK INSTALLATION MANUAL LK-WRG18L JEEP WRANGLER 2018 & UP DRIVER SIDE FRONT...
-
Page 2: Manual Seat
Socket Shoulder Screw for Rear Frame LK-WRG18-BK Bolt Kit LK-WRG18-AB Wire Extension Kit -Left- EW-CK-00 12V Power Supply Wiring Kit LK-UNI-650 Manual Backup Tool Kit PART NUMBER LK-WRG18L DESCRIPTION LINK Jeep Wrangler JL 2018 & Up -Left- 1 of 5 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS... - Page 3 Spiral Spring Tensions Pin 3/16 x 3/4 PRD 192-151 Spring Tension Pin 1/4 x 3/4 PRD 192-135 Spring Tension Pin 5/32 x 3/4 LK752B Pivot Cover -Black- PART NUMBER LK-WRG18L DESCRIPTION LINK Jeep Wrangler JL 2018 & Up -Left- 2 of 5 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 4 Flat Socket Cap Screw M8-1.25 x 25mm G10.9 LK720LB Pivot Motor Cover -Left- Black LK710B Chain Covert -Black- PRD 110-106 Round washer head tapping screw #8 x 3/4 PART NUMBER LK-WRG18L DESCRIPTION LINK Jeep Wrangler JL 2018 & Up -Left- 3 of 5 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 5 Socket Shoulder Screw Zinc Plated 3/8 x 1/2 x 5/16-18 THD PRD 333-107 Nylon Insert Locknut 5/16-18 LK700B Link Covert -Black- L-LK912 PART NUMBER LK-WRG18L DESCRIPTION LINK Jeep Wrangler JL 2018 & Up -Left- 4 of 5 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 6 Nylon Insert Locknut M8-1.25 G8.8 PRD 321-101P Hex Nut Zinc Plated 1/4-20 PRD 303-222P Hex Cap Bolt Zinc Plated 7/16-20 x 1 G5 PART NUMBER LK-WRG18L DESCRIPTION LINK Jeep Wrangler JL 2018 & Up -Left- 5 of 5 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 7 REFERENCES LINK LK-WRG18L *Transfer height: 19”|Average install: 6-8hrs. Seat height: ¾” higher than OEM lowest (adjustable seat) OEM seat trim must be modified. Seat adjustments|FRONT: 2” more than OEM|BACK: 3 ” less than OEM. Lower B pillar shroud needs to be cut |STENCIL PROVIDED.
- Page 8 We have prepared quick, easy and to the point tutorial videos imbedded into the software. Take a moment and watch the video that shows all the features of the tablet. To do this, open the LINK IT app and tap on ‘INFO’.
- Page 9 Make sure the steering wheel adjustment is fully UP and IN to allow maximum clearance for the driver seat. When installing the LINK with hand controls, hand controls should be installed after the LINK. Remove the driver side OEM seat and place on a workbench to be able to remove all the plastic trims, seat handle and lumbar adjuster.
- Page 10 2. Remove the wiring harness and seat position sensor from the seat base. The airbag connector plug goes directly into the seat back and will follow the seat back when removed. LINK Jeep Wrangler 2018 & UP driver side-p.4...
- Page 11 3. Remove the seat cushion. LINK Jeep Wrangler 2018 & UP driver side-p.5...
- Page 12 The front part of the seat lumbar mechanism will have to be modified slightly to allow clearance for the LINK remove the plastic as per the directions. LINK Jeep Wrangler 2018 & UP driver side-p.6...
- Page 13 5. Remove the seat belt receiver. 6. Remove the seat occupant sensor module and pad from the seat pan. Remove the bracket from the module. LINK Jeep Wrangler 2018 & UP driver side-p.7...
- Page 14 Remove the seat cushion support and the seat pan. LINK Jeep Wrangler 2018 & UP driver side-p.8...
- Page 15 The wiring extension will be routed out of the bottom left hand corner of the seat. NOTE: The airbag plug goes directly into the seat back, it will be extended through the provided extension at the same time as the other floor plug. WIRING BEFORE EXTENTION LINK Jeep Wrangler 2018 & UP driver side-p.9...
- Page 16 WIRING AFTER EXTENTION LINK Jeep Wrangler 2018 & UP driver side-p.10...
- Page 17 9. Reconnect the seat position sensor module to the plug, and install the provided sensor bracket on to the module. 10. Remove the upper and lower b pillar trim to access the seat belt pre-tensioner. LINK Jeep Wrangler 2018 & UP driver side-p.11...
- Page 18 M8-1.25X25mm flathead bolt and the M8-1.25X40mm bolt and lock washer. The pre- tensioner will be installed onto the new adapter. 12. The b pillar trim will have to be cut and modified with the provided stencil to allow clearance for the LINK. Modify as per the photos.
- Page 19 LINK Jeep Wrangler 2018 & UP driver side-p.13...
- Page 20 13. Run the power from the battery to the LINK. To do this, thread the red power cable (+) under the doorstep molding and through the firewall. Make sure you pass through a grommet in the firewall to prevent the cable from chaffing. Install the circuit breaker near the battery and then connect the battery to the circuit breaker.
- Page 21 15. The center consul will have to be unbolted and lifted on the left hand side to allow access to the wiring conduit underneath it. 16. Peel back the carpet to access the wiring conduit. Mark it as per the photos, unclip the top part an cut it off. CUT OFF HERE LINK Jeep Wrangler 2018 & UP driver side-p.15...
- Page 22 17. Part of the lower plastic conduit will also have to be cut off as per the photos to allow clearance. CUT OFF HERE LINK Jeep Wrangler 2018 & UP driver side-p.16...
- Page 23 Place the provided plastic cover # LK-WRG18-06 over the carpet and conduit and attach it with a zip tie. Reinstall the center consul. LINK Jeep Wrangler 2018 & UP driver side-p.17...
- Page 24 19. The LINK floor adapter part #LK-WRG18L-01 can now be installed. Use the two OEM bolts at the front and the two provided M10-1.50X35mm at the back. 20. Remove the LINK from the shipping box and set it on a table or workbench. Connect auxiliary 12V power to the LINK.
- Page 25 (8) bolt holes. 22. Place the LINK in the vehicle on the floor adapters. Use the four longer (3/8’’-16 x 1¼’’) socket cap bolts to secure the LINK by the pivot, and use the four shorter (3/8’’-16 x 7/8’’) bolts to secure the interior of the LINK.
- Page 26 NOTE: do not compress the hose with the zip tie this will cause a problem with the occupant sensor. LINK Jeep Wrangler 2018 & UP driver side-p.20...
- Page 27 25. Connect the previously installed 12v power supply to the LINK, and using the ‘BYPASS’ mode on your ADAPT SOLUTIONS tablet carefully ‘PIVOT’ ‘TRAVEL’ and ’TILT’ the LINK out of the vehicle. Install the metal seat pan, using the two OEM bolts and provided 8mm locknuts, and the rear seat cushion support using the provided self tapping screws.
- Page 28 27. Install the lumbar adjuster onto the seat adapter, use the provided self-tapping screws and the ¼ inch nut as a spacer at the rear of the bracket. Push the cable clips into the provided holes and attach with zip ties. LINK Jeep Wrangler 2018 & UP driver side-p.22...
- Page 29 Tuck the seat position sensor under the side of the seat pan and attach with zip ties. Attach with zip tie here around the round bar LINK Jeep Wrangler 2018 & UP driver side-p.23...
- Page 30 Reconnect the remaining connectors and attach the wiring down the side and along the back of the seat adapter. 30. Reconnect and reinstall the seat cushion. Twist the rear clips to provide more tension. LINK Jeep Wrangler 2018 & UP driver side-p.24...
- Page 31 31. Attach the side clips of the seat cushion to the seat back and to the seat adapter. LINK Jeep Wrangler 2018 & UP driver side-p.25...
- Page 32 33. Reinstall the seat back fabric flap under the seat using the elastic straps. Run the wiring extention out of the top left hand corner of the flap. LINK Jeep Wrangler 2018 & UP driver side-p.26...
- Page 33 35. The left hand interior seat trim will have to be cut and modified before installation. Drill the four holes for the LK-WRG18LB-05 before it is reinstalled. replacement cover trim clips # LINK Jeep Wrangler 2018 & UP driver side-p.27...
- Page 34 36. Reinstall the interior trim. Remove the OEM bolt from the recline handle and replace it with the provided ¼- LK-WRG18LB-05. 20x1/2’’ button head bolt. Install the cover # 37. Reinstall the lumbar handle. LINK Jeep Wrangler 2018 & UP driver side-p.28...
- Page 35 39. Attach the extended wiring harness at the back of the seat and at the b pillar, leaving just enough wire to follow the seat in and out. LINK Jeep Wrangler 2018 & UP driver side-p.29...
- Page 36 LINK’s ‘TRAVEL’ and ‘TILT’. Then make sure that the ‘PIVOT’ is completely in. 41. Now that the LINK is in its ‘HOME’ position, RESET the unit by pressing ‘CONFIRM RESET’. A screen will pop up to ask: ‘ARE YOU SURE YOU WANT TO RESET ZERO POSITION’. Press ‘ACCEPT’. The LINK will emit two (2) audible beeps to confirm ‘RESET’, and will now be in reduced power mode.
- Page 37 Unplug the Bluetooth module and plug in the hand pendant. Make sure the LINK hand pendant is working properly. Cycle the LINK in and out a few times, both with and without a passenger to make sure all shrouds are properly installed and that nothing is rubbing or requires adjustment. Make a visual inspection while the LINK is in movement that all the wiring follows the seat and does not risk being severed at any time.
- Page 38 9 Volt Battery The LINK is designed to run off of the vehicle’s 12 volt battery. It is equipped with many safeguards to ensure that the controller box always retains its programing sequence. One of those safeguards is the 9 volt memory backup battery.
-
Page 39: Normal Use
All systems functional and ready to go. Power Reduce Mode To exit, simply run the LINK a full cycle. Major Problem Do not use the LINK - contact your Mobility Equipment Dealer No Response No 12V Power DIAGNOSTIC MODE (Press and hold the power button) Entering Static Diagnostic Current vehicle 12V power supply level. -
Page 40: Year Limited Warranty
ADAPT-SOLUTIONS #1 LTD. 3 YEAR LIMITED WARRANTY Adapt-Solutions # 1 Ltd. (Adapt Solutions), warrants to the original purchaser of a LINK that the equipment is free from defects in material and workmanship for a period of three years from date of purchase. - Page 41 LINK Jeep Wrangler 2018 & UP driver side-p.35...
Need help?
Do you have a question about the LK-WRG18L and is the answer not in the manual?
Questions and answers