Advertisement
Quick Links
Advertisement
Related Manuals for Link LK-F250C11R
Summary of Contents for Link LK-F250C11R
- Page 1 LINK INSTALLATION MANUAL LK-F250C11R FORD F250 CREW CAB 2011-2016 FRONT RIGHT...
- Page 2 Bolt kit LK-F250C11PR-AB Air Bag Kit Electric Seat -Right- EW-CK-00 12V Power Supply Wiring Kit LK-UNI-650 Manual Backup Tool Kit PART NUMBER LK-F250C11R DESCRIPTION 1 of 4 LINK Ford F-250 Supercrew Cab 2011 & Up -Right- |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 3 Thread: 1/4 - 20 UNC Drill 5/16" Step 1: Drill Ø5/16 (2 thickness) Step 2: Drill Ø3/16 Step 3: Thread 1/4 - 20 UNC PART NUMBER LK-F250C11R DESCRIPTION 2 of 4 LINK Ford F-250 Supercrew Cab 2011 & Up -Right- |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 4 Trim Panel Clip Ø1/4'' x 3/4'' Black PRD 333-107 Nylon Insert Locknut 5/16-18 PRD 339-136P Socket Shoulder Screw Zinc Plated 3/8 x 1/2 x 5/16-18 THD PART NUMBER LK-F250C11R DESCRIPTION 3 of 4 LINK Ford F-250 Supercrew Cab 2011 & Up -Right- |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 5 Socket Head Cap Screw Zinc Plated 3/8-16 x 7/8 PRD 332-166P Socket Head Cap Screw Zinc Plated 3/8-16 x 1 1/4 LK-UNI-650 Manual Backup Tool Kit PART NUMBER LK-F250C11R DESCRIPTION LINK Ford F-250 Supercrew Cab 2011 & Up -Right- 4 of 4 |tech@adaptsolutions.ca|866.641.0419|418.889.9838 fax ADAPT SOLUTIONS...
- Page 6 REFERENCES LINK LK-F250C11R *Transfer height: 24”(F-250)|Average install: 6-8 hrs. Seat height: ¼ inch higher than OEM (manual or power seat) OEM shrouds must be trimmed. Seat adjustments|FRONT: 2 inches less than OEM|BACK: OEM Please specify if equipped with power seats.
- Page 7 We have prepared quick, easy and to the point tutorial videos imbedded into the software. Take a moment and watch the video that shows all the features of the tablet. To do this, open the LINK IT app and tap on ‘INFO’.
- Page 8 Remove the passenger side OEM seat, and place on a workbench and remove all the plastic trims. LINK 2011-2016 Ford F250 Crew Cab Front Right p.3...
- Page 9 (if present). Disconnect seat back, 2. Disconnect remove the wiring, and then remove the seat back. Remove the seat cushion. LINK 2011-2016 Ford F250 Crew Cab Front Right p.4...
- Page 10 Remove the seat belt receiver, wire seat cushion supports, and the metal seat pan. LINK 2011-2016 Ford F250 Crew Cab Front Right p.5...
- Page 11 Remove the seat wiring harness. The photos of the wiring harness are for a manually reclining seat. Drill out the rivets that hold the lumbar adjuster, which, will be reinstalled on the LINK seat base. LINK 2011-2016 Ford F250 Crew Cab Front Right p.6...
- Page 12 LINK seat brackets. Cut off the protrusion halve way across and then reinstall. Run the power from the battery to the LINK. To do this, thread the red power cable (+) under the doorstep molding and through the firewall. Make sure you pass through a grommet in the firewall to prevent the cable from chaffing.
- Page 13 The wiring extension will be routed out of the bottom left hand corner of the seat. Control box (if present) will be relocated to the floor. LINK 2011-2016 Ford F250 Crew Cab Front Right p.8...
- Page 14 Remove the LINK from the shipping box and set it on a table or workbench. Connect auxiliary 12V power to the LINK. The LINK will ‘beep’ during the installation. (See LINK Audible Warnings chart for further references.)
- Page 15 Place the LINK in the vehicle on the floor adapter. Use the four longer (3/8’’-16 x 1¼’’) socket cap bolts to secure the LINK by the pivot, and use the four shorter (3/8’’-16 x 7/8’’) to secure the interior of the LINK. Be careful not to pinch the LINK wire harness between the LINK and the floor IMPORTANT: Run the LINK harness around and under the pivot.
- Page 16 Connect the previously installed 12v power supply to the LINK, and using the ‘bypass’ mode on your ADAPT SOLUTIONS tablet carefully ‘pivot’ ‘travel’ and ’tilt’ the LINK out of the vehicle to install the seat. Install the metal seat pan with the self-tapping screws provided.
- Page 17 Install the wire seat cushion supports. Before reinstalling the seat belt receiver, the OEM bolt will have to be replaced by the provided M10-1.5X25mm G.8.8 hex bolt reuse the two washers. LINK 2011-2016 Ford F250 Crew Cab Front Right p.12...
- Page 18 Install the seat cushion onto the seat adapter. The tab on the front right hand side will have to be bent up to allow clearance. Bend the tabs at the bottom of the seat back. LINK 2011-2016 Ford F250 Crew Cab Front Right p.13...
- Page 19 Be sure to attach the unused motor wires in the seat. The seat back, can now be reinstalled onto the LINK. Run the wiring connectors to the seat back. Pay specific attention to firmly fastening the harness where it exits the seat back.
- Page 20 Verify the positioning of the wire to make sure there is no chance of it pinching or binding once the seat moves. 25. Remove the plastic elbow on the seat adjustment switch, harness, before routing the harness. LINK 2011-2016 Ford F250 Crew Cab Front Right p.15...
- Page 21 The right hand side plastic trim, will have to be cut and modified to clear the pivot of the LINK. 27. Reinstall the plastic shroud, seat controls and recline handle. LINK 2011-2016 Ford F250 Crew Cab Front Right p.16...
- Page 22 Attach the extended wiring harness at the back of the seat. Bring the LINK out to verify if you have enough wire to follow the seat in and out. Attach the wire at the lower corner of the LINK. Roll up any excess wiring on the floor under the LINK and reconnect the seat floor connector.
- Page 23 If the LINK is slightly off its ‘HOME’ position or the starting point of its movements, there is a strong chance that the LINK will not fit through the doorway properly and/or will cause problems with the preset of the LINK.
- Page 24 INFO | LINK MANAGEMENT | DIAGNOSTIC. The real voltage will be listed. Unplug the Bluetooth module and plug in the hand pendant. Make sure the LINK hand pendant is working properly. Cycle the LINK in and out a few times, both with and without a passenger to make sure all shrouds are properly installed and that nothing is rubbing or requires adjustment.
- Page 25 9 vo lt b a tte ry is stro ng ly sug g e ste d . T he LINK 's me mo ry b a c k up b a tte ry (9 vo lt) is lo w o r d e a d .
-
Page 26: Normal Use
All systems functional and ready to go. Power Reduce Mode To exit, simply run the LINK a full cycle. Major Problem Do not use the LINK - contact your Mobility Equipment Dealer No Response No 12V Power DIAG NO ST IC MO DE... -
Page 27: Year Limited Warranty
( LINK ) inste a d o f re p a iring o r re p la c ing the o rig ina l e q uip me nt. - Page 28 LINK 2011-2016 Ford F250 Crew Cab Front Right p.23...