Table of Contents
Advertisement
Names of the connector panel terminals
(1)
(2)
(3)
(19) (18)(17)
(16)
(15)
Name
: Main Function
(1) COMPUTER 1 IN
: Connect a VGA cable from a computer.
(2) LAN
: Connect a LAN cable from a computer.
(3) USB
: Connect the USB cable from a computer for firmware
upgrades or keypad remote emulation.
(4) AUDIO IN (1)
: Connect the audio cable from the input device.
(5) COMPUTER 3 IN
: Connect the DVI cable from a computer.
(6) AUDIO IN (3)
: Connect the audio cable from the input device.
(7) AUDIO OUT
: Audio loop through.
(8) MONITOR OUT
: Connect a monitor.
(9) AUDIO IN (2)
: Connect the audio cable from the input device.
(10) RS232C terminal
: When operating the projector via a computer, connect this
to the controlling computer's RS-232C port.
(11) SCREEN TRIGGER
: When connected to the screen through a commercially
available cable, the screen deploys automatically on
start up of the projector. The screen retracts when the
projector is powered off.
(12) Main power switch
: Turn on/off the projector.
(13) S-VIDEO
: Connect a commercially available S-video cable from a video
device.
(14) L/MONO, R
: Connect an RCA audio cables from the input device right and
(Component)
left channels.
(15) AC IN
: Connect the supplied power cable.
(16) L/MONO, R (Video)
: Connect RCA audio cables from the input device right and
left channels.
This audio jack is shared with S-Video input.
(17) VIDEO IN
: Connect a composite video cable from a video device to the
yellow RCA jack.
(18) COMPONENT IN
: Connect a component video enabled device.
(Y, Cb/Pb, Cr/Pr)
(19) COMPUTER 2 IN
: Connect RGBHV or Component signal from computer or
(R/PR, G/Y, B/PB, H, V)
component video enabled device.
(4)
(5)
(6) (7)
(8)
(9)
(10)
(14)
(13)
(12)
(11)
p.79
p.80
Preparing and using the remote control
Loading dry-cell
batteries
into the remote control
Remove the battery cover.
1
Insert the dry-cell batteries.
Be sure to align the plus and minus ends of
the batteries properly.
Two batteries (LR03, SIZE AAA) are used.
Replace the battery cover.
Dry-cell batteries
•
Before using the batteries, be sure to observe the Safety Precautions described in previous pages.
•
If the remote control stops working, or if its range decreases, replace all the batteries with new
ones. (2 batteries (LR03 SIZE AAA))
•
Do not heat, take apart, or throw batteries into fire.
•
Do not use new and old batteries together, or different types of batteries together.
•
Dispose of used batteries according to local regulations.
•
Remove batteries from remote control when not using for extended periods.
•
Keep the batteries away from the reach of children.
Batteries are choking hazards and can be very dangerous if swallowed. If the batteries are
swallowed, seek medical assistance immediately.
The remote control
•
Avoid exposing the remote control infrared sensor to bright sunlight or fluorescent lighting.
•
Do not drop or bang.
•
Do not leave in hot or humid locations.
•
Do not allow it to get wet or place it on top of wet objects.
•
Do not take it apart.
•
Ensure that the battery polarities (+/–) are aligned correctly.
•
In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.
Operating the remote
control
Point toward the projector's infrared
remote sensor, and press a button
on the remote control.
•
Operating the projector from the front
Approx. 15°
Note
•
The above operation is also applicable
for the remote control operation from
rear side.
Advertisement
Table of Contents
