Others; Trouble Indications; On/Standy Led; Status Led - Toshiba TDP-WX5400 Owner's Manual

Trouble indications

The indicator lights to inform you of internal abnormalities.

ON/STANDY LED


ON/STANDBY STATUS
Projector Status LED
Condition
AC Off Blank
Cooling Orange Blink
Power Up Sequence Green Blink
Standby / Idle Orange On
Power On Green On

Status LED


Projector Status LED Condition
Normal Condition Off
Cover ERROR Blink Red once
(repeat)
Temperature Blink Red twice
ERROR (repeat)
Power ERROR Blink Red 3 times
(repeat)
Fan ERROR Blink Red 4 times
(repeat)
Key lock Active Orange
(when key pressed)
Idle Green On

Lamp LEDs


Projector Status LED Condition LED Sequence
Lamp Off Off
End of Lamp Life Red Blink
No Lamp Blink Red once
(repeat)
Lamp ERROR Blink Red 6
times (repeat)
Cooling Lamp Orange Blink
Re-light Up Green Blink
Sequence
Lamp Life Over Red On
(cannot turn on)

Others

LAMP1 LAMP2
LED Sequence Projector
Condition
Off
0.5 sec On g 0.5 sec Off After Power Off
0.5 sec On g 0.5 sec Off Power Up
On
On
LED Sequence Projector
Condition
Off Power On
0.5 sec On g 2.5 sec Off ERROR
0.5 sec On g 2.5 sec Off ERROR
x 2 times g 2.0 sec Off
0.5 sec On g 2.5 sec Off ERROR
x 3 times g 2.0 sec Off
0.5 sec On g 2.5 sec Off ERROR
x 4 times g 2.0 sec Off
On Key lock Active
On
Projector Condition
Off Always
0.5 sec On g 0.5 sec Always
Off
0.5 sec On g 2.5 sec ERROR
Off
0.5 sec On g 2.5 sec ERROR
Off x 6 times g 2.0 sec
Off
0.5 sec On g 0.5 sec Switching lamp 1 and
Off 2
0.5 sec On g 0.5 sec Power Up
Off
On Always
74

Before calling service personnel

If you think something is wrong, check the followings before contacting customer service.
Please see "Trouble indications"
p.74
If This Happens
No power •
Is the power cord plugged in? Is it connected to the projector?
• Is the main power switch turned on?
•
Is the lamp cover attached properly?
Power goes out
• Is the ambient temperature high?
during use • Is the air intake or air exhaust blocked?
No picture •
Is the correct source selected?
• Is the mute function on?
• Is the brightness setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
No audio
• Is the mute function on?
• Is the volume setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
Picture not
• Is the input signal supported by the projector?
displayed • Is there something generating an abnormal video signal, for
correctly
instance the video tape?
Picture blurred • Is the lens dirty?
Part of picture
• Is the lens focus adjusted optimally?
out of focus • Is the projection distance within the supported range?
•
Is the projector's screen placement angle tilted too far?
• Are the sharpness or phase adjustments off?
Image is dark • Are the brightness or contrast adjustments off?
• Is the lamp nearing the end of its service life?
Colors too light •
Are the color, tint, R-level, G-level, or B-level adjustments off?
Bad shading
p.50 p.51
•
Is the screen dirty?
• Is the lamp nearing the end of its service life?
Control panel key •
Is the key lock function on?
doesn't work
Remote control • Are the remote control's batteries drained?
doesn't work
• Are the batteries inserted into the remote control correctly?
• Is the remote control being used within the effective range?
•
Are there any obstructions between the remote control and
projector?
•
Are there any fluorescent or other bright lights shining at the
projector infrared remote sensors?
as well.
Check
p.36
p.67
p.74
p.74
p.38
p.43
p.50
p.28
p.43
p.40
p.28
p.78
p.70
p.39
p.26
p.26
p.50 p.53
p.50
p.59
p.59
p.56
75
p.23
p.23