Power Supply Information; Moisture Condensation - Toshiba TDP-WX5400 Owner's Manual

Toshiba tdp-wx5400: user guide
Hide thumbs Also See for TDP-WX5400:
Table of Contents

Advertisement

IMPORTANT SAFETY INSTRUCTIONS (Continued)
20. If glass components, including
lens and lamp, should break,
contact your dealer for repair
service.
This product incorporates glass
components, including a lens and
a lamp. If such parts should break,
please handle with care to avoid
injury and contact your dealer for
repair service. The broken pieces
of glass may cause to injury. In the
unlikely event of the lamp rupturing,
thoroughly clean the area around
the projector and discard any edible
items placed in that area.
21. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service
personnel.
22. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics as
the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
23. Safety Check
Upon completion of any service
or repairs to this product, ask the
service technician to perform safety
checks to determine that the product
is in proper operating condition.
24. Do not leave thermal-paper
documents or easily deformed
items on top of the unit or
near the air exhaust for long
periods of time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
25. Do not use the product in a
closed installation state.
Do not place the product in a box
or in any other closed installation
state. Otherwise it may overheat. This
could result in a risk of fire.
8

POWER SUPPLY INFORMATION

If your line voltage is 220 to 240V, use one of the following types of cable/plug.
Plug
configuration Plug type
Line voltage
EURO
220 – 240V
UK
220 – 240V
Use a 5A fuse which is approved by ASTA
or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
IMPORTANT PRECAUTIONS

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the lens
and the crucial internal parts. To prevent the unit from possible damage, do not use the unit for
at least 2 hours when there is an extreme or sudden change in temperature.
Place and Manner of Installation
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High].
Only plug the power cord into outlets rated for use with the power cord's specified voltage
range. Do not overload extension cords or table taps as this can result in fire or electric
shock.
Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall down, which could result in severe injury.
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Plug
configuration
Plug type
Line voltage
Australian
200 – 240V
240V
10A
Switzerland
200 – 240V
240V
6A
North American
200 – 240V
240V
15A
p.58


Advertisement

Table of Contents
loading

This manual is also suitable for:

Tdp-wx5400u

Table of Contents